Comtrend Corporation CT-6382T Operation & User’s Manual
|
Comtrend Corporation CT-6382T, 4.2.3 ATM statistics The following figure shows the ATM statistics screen. ATM Interface Statistics Field Description In Octets Number of received octets over the interface Out Octets Number of transmitted octets over the interface In Errors Number of cells dropped due to uncorrectable HEC errors In Unknown Number of received cells discarded during cell header validation, including cells with unrecognized VPI/VCI values, and cells with invalid cell header patterns. If cells with undefined PTI values are discarded, they are also counted here. In Hec Errors Number of cells received with an ATM Cell Header HEX error In Invalid Vpi Vci Erro
10.1.3 Restore Default Clicking the Restore Default Configuration option in the Restore Settings screen can restore the original factory installed settings. NOTE: This entry has the same effect as the hardware reset-to-default button. The CT-6382T board hardware and the boot loader support the reset to default button. If the reset button is continuously push
Comtrend Corporation CT-6382T, 8.1 MGCP STEP 1: Select MGCP on the menu; the current configuration of the Media Gateway will be displayed. STEP 2: Enter the MGCP Gateway and Call Agent information for your Service provider. The fields are explained below. • Gateway MGCP Client name: Enter the MGCP client name. Interface Name: Select the LAN interface or WAN interface. Gateway Binding interface for MGCP Call Signaling control, e.g. “ppp0” for PPPoE or PPPoA, “atm0” for RFC1483 routed, and “mer0” for MER encapsulation. Locale Selection: Sets tone, ring type and physical characteri
Comtrend Corporation CT-6382T, 7. The following screen will be displayed. To enable the wireless function, select the box (by clicking on it) and input the SSID. Then, click Next. 8. The WAN Setup-Summary screen presents the entire configuration summary. Click Save/Reboot if the settings are correct. Click Back if you wish to modify the settings. 9. After clicking Save/Reboot, the IAD will save the configuration to the flash memory, and reboot. The Web UI will not respond until the system is brought up again. After the system is up, the Web UI will refresh to the Device Info page automat
Chapter 4 Device Information After login, the Quick Setup screen appears as shown. Depending on the network operating mode, and whether NAPT and firewall are enabled or disabled, the main panel will display or hide the NAPT/Firewall menu. For instance, at initial setup, the default network operating mode is Bridge. The main panel will not show the NAPT and
Comtrend Corporation CT-6382T, Step4: Select Connect to a printer on the Internet, type “http://192.168.1.1:631/printers/hp3845” and click “Next”. The printer name “hp3845” must be the same name entered in the ADSL modem WEB UI “printer server setting” as in step 1. Step 5: Click “Have Disk”, insert printer driver CD. 124
Comtrend Corporation CT-6382T, 6.2 LAN Configure the VoIP IAD IP Address and Subnet Mask for LAN interface. Save button only saves the LAN configuration data. Save/Reboot button saves the LAN configuration data and reboots the IAD to make the new configuration effective. IP Address: Enter the IP address for the LAN port. Subnet Mask: Enter the subnet mask for the LAN port. Enable UPnP: Tick the box to enable. Note: This option will not display in Bridge mode or if no PVC is configured. Enable IGMP Snooping: Enable IGMP Snooping function by ticking the box. Standard Mode: In standard mode, as in all prior releases, multicast traffic will
Comtrend Corporation CT-6382T, 5. Upon completion, click Next. The following screen appears. The Device Setup page allows the user to configure the LAN interface IP address and DHCP server. If the user would like this VoIP IAD to assign dynamic IP addresses, DNS server and default gateway to other LAN devices, select the radio box Enable DHCP server to enter the starting IP address and end IP address and DHCP lease time. This configures the IAD to automatically assign IP addresses, default gateway address and DNS server addresses to each of your PCs. Note that the IAD’s default IP address is 192.168.1.1 and the default private address range provided by the DHCP serv
Comtrend Corporation CT-6382T, 6.6.2 Static Route Choose Static Route to display the Static Route screen. The Static Route screen lists the configured static routes, and allows configuring static routes. Choose Add or Remove to configure the static routes. Note: This screenshot is based on PPPoE encapsulation. To add static route, click the Add button to display the following screen. Enter the destination network address, subnet mask, gateway AND/OR available WAN interface then click Save/Apply to add the entry to the routing table. 71
Comtrend Corporation CT-6382T, Certificate Name A user-defined name for the certificate. Common Name Usually, it is the fully qualified domain name for the machine. Organization Name The exact legal name of your organization. Do not abbreviate. State/Province Name The state or province where your organization is located. It cannot be abbreviated. Country/Region Name The two-letter ISO abbreviation for your country. Click Apply to generate a private key and a certificate signing request. This page is used to paste the certificate content and the private key provided by your vendor/ISP/ITSP. 82
Comtrend Corporation CT-6382T, The extra items are explained here. MSGc (number of bytes in overhead channel message) 65 14 B (number of bytes in Mux Data Frame) 254 13 M (number of Mux Data Frames in FEC Data Frame) 1 16 T (Max Data Frames over sync bytes) 3 9 R (number of check bytes in FEC Data Frame) 0 8 S (ratio of FEC over PMD Data Frame length) 0.3047 5.9678 L (number of bits in PMD Data Frame) 6695 311 D interleaver depth): 1 8 Delay (msec): 0 11 25
8. After clicking Save/Reboot, the IAD will save the configuration to the flash memory, and reboot. The Web UI will not respond until the system is brought up again. After the system is up, the Web UI will refresh to the Device Info page automatically. The CT-6382T is ready for operation and the LEDs display as described in the LED description table
Comtrend Corporation CT-6382T, Chapter 8 Voice The MGCP option is used to verify the MGCP application configured by you. We will use the scenario illustrated in the following diagram to explain the Web configuration: To access MGCP, Simply click on the Voice->MGCP from main menu. 99
Chapter 2 Installation 2.1 Hardware Installation In the rear panel, there is a reset button. To load the factory default settings, hold the reset button down for at least 5 seconds. If held down for more than 12 seconds, the VoIP IAD will go into firmware update state and the user can update the VoIP IAD from web-interface @192.168.1.1 without ID/Passw
Comtrend Corporation CT-6382T, DTIM Interval Delivery T raffic Indication Message (DTIM), also known as Beacon Rate. The entry range is a value between 1 and 65535. A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages. When the AP has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. AP Clients hear the beacons and awaken to receive the broadcast and multicast messages. The default is 1. Beacon Interval The amount of time between beacon transmissions. Each beacon transmission identifies the presence of
Comtrend Corporation CT-6382T, ATM AAL5 Layer Statistics over ADSL interface Field Description In Octets Number of received AAL5/AAL0 CPCS PDU octets Out Octets Number of received AAL5/AAL0 CPCS PDUs octets transmitted In Ucst Pkts Number of received AAL5/AAL0 CPCS PDUs passed to a higher-layer for transmission Out Ucast Pkts Number of received AAL5/AAL0 CPCS PDUs received from a higher layer for transmissions In Errors Number of received AAL5/AAL0 CPCS PDUs received that contain an error. The types of errors counted include CRC-32 errors. Out Errors Number of received AAL5/AAL0 CPCS PDUs that coul
Comtrend Corporation CT-6382T, Chapter 3 Login via the Web Browser This section describes how to manage the VoIP IAD via a Web browser via the remote end. You can use a web browser such as Microsoft Internet Explorer, or Netscape Navigator. (The Web page is best viewed with Microsoft Internet Explorer 5.0 and later): A unique default user account is assigned with user name root and password 12345. The user can change the default password later when logged in to the device. 3.1 IP Address Note: When the CT-6382T is switched on, the DHCP server will start automatically. The default address for the CT-6382T is 192.168.1.1 and DHCP is enabled as default for
Comtrend Corporation CT-6382T, 3.2 Login Procedure Perform the following steps to bring up the Web user interface and configure the CT-6382T. To log on to the system from the Web browser, follow the steps below: STEP 1: Start your Internet browser. Type the IP address for the VoIP IAD in the Web address field. For example, if the IP address is 192.168.1.1, type http://192.168.1.1 STEP 2: You will be prompted to enter your user name and password. Type root in the user name and 12345 in the password field, and click OK. The password can be changed later in the Web U
6.10 Port Mapping Port Mapping supports multiple port to PVC and bridging groups. Each group will perform as an independent network. To support this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button. The Remove button will remove the grouping and add the ungrouped interfaces to the Default group. As shown below, when you tick
Comtrend Corporation CT-6382T, STEP 3: Then, choose the Encapsulation mode. Select Enable 802.1q (by ticking the box) if required, and input a number for the VLAN ID. Click Next. STEP 4: Click Next to display the following screen. Choosing different connection types pops up different settings requests. Enter appropriate settings that are requested by your service provider. The following descriptions state each connection type setup separately. 32
Comtrend Corporation CT-6382T, Option Description Enable Wireless A checkbox that enables or disables the wireless LAN interface. When selected, the Web UI displays Hide Access point, SSID, and County settings. The default is Enable Wireless. Hide Access Point Select Hide Access Point to protect VoIP IAD access point from detection by wireless active scans. If you do not want the access point to be automatically detected by a wireless station, this checkbox should be de-selected. The station will not discover this access point. To connect
Comtrend Corporation CT-6382T, 4. Click Next to display the following screen appears. Enable NAT checkbox: If the LAN is configured with a private IP address, the user should select this checkbox. The NAT submenu on the left side main panel will be displayed after reboot. The user can then configure NAT-related features after the system comes up. If a private IP address is not used on the LAN side, this checkbox should be de-selected to free up system resources for better performance. When the system comes back after reboot, the NAT submenu will not be displayed on the
Comtrend Corporation CT-6382T, 6.11 Certificate A certificate is a public key, attached with its owner’s information (company name, server name, personal real name, contact e-mail, postal address, etc) and digital signatures. There will be one or more digital signatures attached on the certificate, indicating that these signers have verified that the owner information of this certificate is correct. 6.11.1 Local Click Create Certificate Request to generate a certificate signing request. The certificate signing r
Comtrend Corporation CT-6382T, 10.1.1 Configuration Backup The Backup option under Management>Settings saves your IAD configurations to a file on your PC. Click Backup Settings in the main window. You will be prompted to define the location of the backup file to save. After choosing the file location, click Backup Settings. The file will then be saved to the assigned location. 105
Comtrend Corporation CT-6382T, Wireless connection Pass: Indicates that the Wireless interface from your computer is connected to the wireless network. Down: Indicates that the VoIP IAD does not detect the wireless network. ADSL Synchronization Pass: Indicates that the DSL modem has detected a DSL signal from the telephone company. A solid ADSL LED on the IAD also indicates the detection of a DSL signal from the telephone company. Fail: indicates that the DSL modem does not detect a signal from the telephone company’s DSL network. The ADSL LED will turn off. 103
Comtrend Corporation CT-6382T, 2. Filter Name : In_Filter2 Protocol : UDP Source Address : 210.168.219.45 Source Subnet Mask : 255.255.0.0 Source Port : 5060:6060 Dest. Address :192.168.1.45 Dest. Sub. Mask : 255.255.255.0 Dest. Port : 6060:7070 This rule will ACCEPT all UDP packets coming from WAN interface mer_0_35/nas_0_35 with IP Address/Sub.Mask 210.168.219.45/16 and a source port in the range of 5060 to 6060, destined to 192.168.1.45/24 and a destination port in the range of 6060 to 7070. All other incoming packets on this interface are DROPPED. MAC Layer Filtering: Th
Comtrend Corporation CT-535 Wireless Router Operation & user’s manual
CT-535 |
D-Link DWL-G710 - AirPlus G Wireless Range Extender Wireless Router Features and benefits
DWL-G710 - AirPlus G Wireless Range Extender |
Sitecom WL-612 Wireless Router Operation & user’s manual
WL-612 |
TP-Link TD-W8951ND Wireless Router Operation & user’s manual
TD-W8951ND |
Comtrend Corporation CT-5365 Wireless Router Quick start manual
CT-5365 |
Comtrend Corporation CT-5365 Wireless Router Operation & user’s manual
CT-5365 |
Comtrend Corporation CT-5361T Wireless Router Operation & user’s manual
CT-5361T |
SMC Networks SMC Barricade g SMC7904WBRA2 Wireless Router Operation & user’s manual
SMC Barricade g SMC7904WBRA2 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Transcension | DC-4P | Operation manual | transcension/dc-4p-B19.pdf | 14 Oct 2023 | 3 | |
2 | Dell | PowerVault 130T | Operation & user’s manual | dell/powervault-130t-291.pdf | 24 Oct 2022 | 104 | 3.74 Mb |
3 | Fiil | RUNNER | Operation & user’s manual | fiil/runner-55P.pdf | 03 Jan 2023 | 18 | |
4 | ratiotec | Compact | Instruction manual | ratiotec/compact-I98.pdf | 19 Aug 2023 | 40 | |
5 | BMW | R50 | Installation instructions manual | bmw/r50-287.pdf | 10 Dec 2023 | 17 | |
6 | Canon | LEGRIA HF R16 | Specification sheet | canon/legria-hf-r16-591.pdf | 18 Oct 2022 | 3 | 0.07 Mb |
TP-Link
Specifications are subject to change without notice. TP-LINK is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders.No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformati …
Archer D2(21 pages) |
SMC Networks
www.smc-europe.com www.smc.comEliteConnect™WLAN Access ManagerData SheetSMC2502WThe SMC EliteConnect WLAN Access Manager (SMC2502W) is an ideal solution for protecting, managing, and controlling your wireless network. Supporting up to four Access Points, the SMC WLAN Access Manager utilizes a high performance packet inspection engine to mon …
SMC2502W(2 pages) |
D-Link
©2007 D-Link Austraresp Before Yo1. If you purccomputersProvider (2. It is best tDSL-2740the necesnetwork a Check Yo If any of theThis product can beany current web broInternet Explorer 6 oNavigator 6.2.3. alia Pty Ltd. All rights reserved. Tpective holders. Software and speDSL-2740B Aou Begin chased this Router to share ys, you must have a …
DSL-2740B(15 pages) |
KING
Automatic Directional Wi-Fi Antennaincludes the KING WiFiMax Router KWM1000KF1000 • WhiteKF1001 • BlackCONTENTS OPERATION ....................................................................................... 1-20 INSTALLATION ................................................................................ 22-29 TROUBLESHOOTING ......................... …
Falcon KF1000(36 pages) |
NetComm
NetCommWirelessPRODUCT DATASHEETNetCommWirelessNB16DGN600 Dual Band WiFi Gigabit Modem RouterPerfect for• Connecting to your xed line ADSL service• Future proong with a Gigabit WAN port for high speed connection to the NBN and support for IPv6 addressing• Sharing your connection with high speed WiFiKEY FEATURES Fully featured ADSL2+ Modem R …
NB16DG(2 pages) |
TRENDnet
TRENDnetTRENDware, USAWhat's Next in NetworkingThe 108Mbps 802.11g MIMO Wireless access point gives your wireless devices the freedom to operate at any location with reduced system interference or dropouts. Add this device to your Ethernet network, and you'll have reliable, high-speed wireless access, which provides wider coverage than standard 802 …
TEW-610APB(2 pages) |
DVS Desktop ClipsterDVS Desktop Hardware manual (File: dvs-clipster-hardware-manual-86, Saturday 16-12-2023) Clipster, 86 |
Telexper DVR tx168 seriesUser Manual: Telexper tx168 series (88ZE1D, Upd.26/12/2023) tx168 series, 25 |
AEG Oven COMPETENCE 5200 BOven Instruction book (AEG COMPETENCE 5200 B) COMPETENCE 5200 B, 32 |
Apple Software Mac OS X Server Web Technologies Administration For Version 10.3 or LaterApple Product User Manual: Mac OS X Server Web Technologies Administration For Version 10.3 or Later PDF Manual - 9M5FL1 Mac OS X Server Web Technologies Administration For Version 10.3 or Later, 54 |
Carrier Dryer 38AK007PDF User Manual (@Q57DXI), Carrier 38AK007 Dryer (Thursday 09-11-2023) 38AK007, 16 |
MK Diamond Products Saw MK-370MK-370 (Saw ePDF Manual, #8544IW) MK-370, 10 |
Supermicro Server Supero A+ SERVER 4042G-6RFSupermicro Product Guide: Supero A+ SERVER 4042G-6RF PDF Operation & user’s manual - I993VF Supero A+ SERVER 4042G-6RF, 114 |
ACT Other ACTPRO 1000ACT Other ACTPRO 1000 Installation notes ACTPRO 1000, 2 |
DFI Motherboard G586OPBDFI G586OPB User Guide (Doc Type: Motherboard Operation & user’s manual) G586OPB, 106 |
Omega Power Pump OMEGAFLEX FPU100 SeriesOmega Power Pump OMEGAFLEX FPU100 Series Operation & user’s manual OMEGAFLEX FPU100 Series, 12 |
Viking Burner VGSB152TVGSB152T (Burner ePDF User Guide, #23833A) VGSB152T, 7 |
Aspire Control Systems RFTCPControl Systems #9KW566 RFTCP, 30 |