Concept Pro VXH264D-16 Operation & User’s Manual
|
20 CONFIGURING THE VXH264D CAMERA To select or deselect specific areas, press ENTER to bring up the yellow cursor square in the top left of the display. Move the cursor using the CURSOR KEYS to the first corner of the area to be set and press ENTER – The grid square retains the yellow cursor square. Press ENTER to change from selected to deselected (or vice ver
Concept Pro VXH264D-16, 43 USING THE REMOTE CLIENT The timeline at the bottom of the display shows a graphical overview of recorded footage for a particular day. Different colour blocks represent different types of recording. ORANGE: Continuous PINK: Panic PURPLE: Alarm BLUE: Motion CYAN: PRE DATE: Choose the required date by selection drop down box and select the date required. TIME: Either use the same method again to select the time or drag the blue time b ar along the timeline. When sliding this time bar you will notice the time changes in the boxes above. Click PLAY to begin playback from the selected date and time. Click the search tab to switch to search mode. REMOTE CLIENT PL
Concept Pro VXH264D-16, 7 CONFIGURING THE LIVE DISPLAY MULTI SCREEN MODE 6 different display modes are supported by the 16 channel VXH264D. By repeatedly pressing the DISPLAY button, the operator can choose between single, 4, 6, 8, 9, and 16 screen as well as basic sequence modes. All the display modes are static with the exception of the sequence mode. In this mode, the sequence symbol ( ) is displayed and each channel is shown in full screen for a set period of time (default 5 seconds) before switching to the next channel. The sequence runs i ndefinitely until a different display mode is chosen. To view a particular channel in full screen, press the corresponding CHANNEL
37 CONNECTING TO THE VXH264D REMOTELY HOW TO CONNECT Input the IP Address and Web Server port of the DVR in the Internet Explorer Address Bar. e.g. http://192.168.2.19:8080 (Web Port :8080) If you do not have a fixed IP address and are using the DDNS service, input the URL as below. e.g. http://1234.dvrlink.net:8080 (Web Port :8080) Please replace “1234” with the default MA
Concept Pro VXH264D-16, 33 RECORDING SIZE / FPS / QUALITY To change SIZE / FPS / QUALITY settings, highlight CONTINUOUS / MOTION RECORDING and press ENTER. Ensure SIZE / FPS / QUALITY is highlighted in blue and press ENTER again. The 24 hour time bar is highlighted in yellow. Press ENTER to display the orange cursor. The orange cursor shown represents one hour (in this case between 00:00 and 01:00). The table below the time bar shows the recording settings for this time period. Example: To change the recording settings between 09:00 and 18:00: Use the C
Concept Pro VXH264D-16, 18 CONFIGURING THE VXH264D CAMERA CAMERA: COLOUR SETUP Brightness, contrast, tint and colour can be adjusted for each individual channel. Highlight which channel to modify and press ENTER. The selected channel is displayed in full screen. BRIGHTNESS, CONTRAST, TINT and COLOUR can be changed as necessary. To modify a different channel, highlight CAMERA and choose the desired channel. Press RETURN when all changes are complete. CAMERA: PTZ SETUP ADDRESS: The unique ID of the PTZ device. PROTOCOL: The protocol of the PTZ device. BAUD RATE: The baud rate of the PTZ device. PTZ properties can
Concept Pro VXH264D-16, 54 APPENDIX B: CONFIGURING A NETGEAR DG384 ROUTER FOR USE WITH VXH264D USING DDNS TO CONNECT DDNS (Dynamic Domain Name Server) is generally used when your ISP provides you with a dynamic public IP address. The problem with a dynamic IP address is that because it can change regularly, any remote users that need to connect to the VXH264D do not know what IP address to enter in the remote client! Using DDNS solves this problem. When a VXH264D is correctly configured to use DDNS, it regularly interrogates the router and sends the current public IP address to a 3rd party database. The VXH264D also sends its MAC address, which is unique. Before using DDNS, the VXH264D must be
Concept Pro VXH264D-16, 17 CONFIGURING THE VXH264D Press the SETUP button to bring up the SYSTEM / RECORD setup option on screen. (If the status bar is not visible you will need to press the setup button twice). Use the CURSOR KEYS to select SYSTEM SETUP and press ENTER. Only authorised users or ADMIN users can configure the VXH264D. Enter the default password of ‘1234’. To navigate around any items in the setup menu, use the CURSOR KEYS and the ENTER and RETURN buttons. In general, the ENTER button is used to select and change a particular item and the RETURN button is used to cancel a change or exit from a particular setup scre
45 REMOTE CLIENT PLAYBACK CONTROLS SEARCH BY EVENT To search for an event and to playback the recorded footage, click SEARCH BY EVENT. Choose the ‘Start time’ and ‘End time’. Select which events to include in the search and click ‘Search’. The event log for the selected time period is displayed below, the ordered can be changed from nearest to farthest. By clicking any of the events,
Concept Pro VXH264D-16, 13 ARCHIVING The Archiving screen allows the operator to choose exactly what to back-up and to which storage device. Use the CURSOR KEYS to navigate around the Archiving screen. To change any value or setting: Press ENTER to change the blue cursor to yellow. Use the up and down CURSOR KEYS to change the value Press ENTER to accept the value or RETURN to cancel To change a tick box setting, press ENTER to toggle on or off SELECT DEVICE: Choose between DVD-RW or USB / FTP back-up device FROM / TO: Start and end time to back-up TAG NAME: The name of the archive set LOG: When selected, the event log for the particular archiv
Concept Pro VXH264D-16, 1 BEFORE INSTALLING BEFORE INSTALLING • Installation should be carried out only by qualified personnel and in accordance with electrical regulations in force. • The DVR must be placed on a stable surface or mounted in an approved cabinet. Adequate ventilation must be provided, taking particular care not to block any of the air vents on the DVR. • Adequate protection against lightning strikes and power surges must be installed to prevent damage to the
Concept Pro VXH264D-16, 53 APPENDIX B: CONFIGURING A NETGEAR DG384 ROUTER FOR USE WITH VXH264D SETTING-UP PORT FORWARDING This section assumes that you have already established a successful connection locally. Log-on to the DG834 and select ‘Services’ from the menu. Click ‘Add Custom Service’ and enter the following values: Name: VXH264D (or any other name of your choice) Type: TCP Start Port: 8080 Finish port: 8080 And click ‘Apply’ Then, create a firewall rule as follows: Select ‘Firewall Rules’ from the menu. Under the inbound services, click ‘Add’ and enter the following: Service: VXH264D (TCP:8080) – This is the service you created earlier. Action: Leave at ‘ALLOW always�
Concept Pro VXH264D-16, 21 CONFIGURING THE VXH264D DISPLAY To set-up the various display options, highlight DISPLAY and press ENTER. STATUS BAR: Turns the status bar at the bottom of the live display ALWAYS ON or auto off delay time. DATE & TIME: Determines whether the Date and Time is shown when the staus bar is removed / timed out. CAMERA TITLE: Determines whether the camera title is displayed. RECORDINGMODE ICON: Determines whether the VXH264D recording status i s shown at the top right of each channel display window. BORDER: Determines whether there is a border around each channel in multi screen display mode. BORDER COLOUR: If the border is ON, the operato
Concept Pro VXH264D-16, 23 CONFIGURING THE VXH264D DISPLAY When all the channels have been completed, press CONFIRM to save the sequence screen and begin creating the next one. Up to 16 different sequence screens can be created. To finish editing the sequence, press CLOSE and then APPLY to save & exit. The new sequence is now saved and can be started by pressing the SEQ button when in live view. DISPLAY: SEQUENCE continued DISPLAY: SPOT-OUT The VXH264D has 4 SPOT MONITOR OUTPUTS. Each one displays a full screen sequence of particular channels, depending on the settings configured in this menu. For each spot monitor, the ope
Concept Pro VXH264D-16, 34 RECORDING RESOLUTION: Recording resolutions of CIF (352x288), 2 CIF(704x288) or D1 (704x576) can be selected for each channel. FPS: Frame rates between 1 and 25 can be set for each channel. QUALITY: Five different picture recording qualities can be set for each channel. AUDIO: If audio devices are connected to the VXH264D then you can select them to be ON or OFF. During playback, when a particular channel is selected in full screen, the assigned audio c hannel will be played back at the same time. Adjust values as desired and select OK to finish and return to the parame
3 FRONT PANEL DESCRIPTION HOLD RW . ZOOM OUT FF . ZOOM IN NEAR FAR CLOSE OPEN FOCUS IRIS DISPLAY SEQ PANIC ZOOM LOCK ARCHIVE PTZ SETUP SEARCH RETURN ENTER ! ± + 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PWR REC NET USB ports Supports a wide variety of USB memory stick for archive, system setting backup and firmware upgrade. An additional USB port is a
Concept Pro VXH264D-16, 16 QUICK MENU If you are using the USB mouse to control the VXH264D pressing the right hand mouse will bring up the Quick Menu. FREEZE: Selecting FREEZE ON will freeze the live view picture for the selected channel. To go back to live view select FREEZE OFF. PTZ: Selecting PTZ will bring up the PTZ control screen. PTZ can only be controlled by an authorised user. ZOOM: Selecting ZOOM will bring up the digital zoom control. R ECORD START: Starts the panic record mode. Use the right mouse click to select. RECORD STOP to stop the panic record mode.
Concept Pro VXH264D-16, 56 APPENDIX D: SPECIFICATIONS MODEL Operation Video in Audio in Main displays Spot displays Audio out External alarm User interface Recording Playback Archiving Time PTZ POS System Network Remote Access Storage Event handling Security Physical Genuine Pentaplex Channels Connection Loop through Channels Connection BNC VGA S-Video HDMI Screen display modes Sequence Digital zoom Channels Connection Display mode Channels Connection Inputs Outputs On-screen display Control Video CODEC Resolution options for each channel Maximum total frame rate Image quality Pre-event recording Recording modes F
Concept Pro VXH264D-16, 42 USING THE REMOTE CLIENT PTZ Internet explorer allows all telemetry control of devices connected to the VXH264D, provided that the correct user authority has been set-up. Click the appropriate channel and use the on screen directional buttons to control pan & tilt movements. Use the - / + keys next to the Focus, Zoom and Iris buttons to control these functions if available on the camera. PRESETS Presets can be programmed and called remotely using the SET and RUN buttons. Example: To start pattern tour 1 running on a VHSD-770EXT speed dome, select preset 131 from the drop down list and
Concept Pro VXH264D-16, 31 CONFIGURING THE VXH264D EVENT / SENSOR EVENT / SENSOR: BUZZER OUT Determines the behaviour and actions that will trigger the internal buzzer. Behaviour settings OPERATION: The internal buzzer can be enabled or disabled. HDD EVENT: Determines whether a hard drive event sounds the buzzer. MODE: Can be either TRANSPARENT (the buzzer sounds only when the trigger criteria is present) or LATCHED. (the buzzer sounds for a set period of time after the trigger) DURATION: In LATCHED mode, the time that the buzzer sounds after it has been triggered. A ctio
Concept Pro VXH264D-16, 22 CONFIGURING THE VXH264D DISPLAY DISPLAY: SEQUENCE When the SEQ button is pressed, the default sequence will cycle through all 16 channels, one by one. Sequence setup allows the operator to define a custom sequence using mixed multi screen views and any desired channels. To add a new sequence, highlight ADD and press ENTER. Sequence title is highlighted – press ENTER to bring up the virtual keyboard and key in a name or reference number for the new sequence. Move around the virtual keyboard using the CURSOR KEYS and ENTER to select a
Panasonic WVPS154 - CAMERA DRIVE UNIT Security Camera Operating instructions manual
WVPS154 - CAMERA DRIVE UNIT |
Spypoint BF-6 Security Camera Operation & user’s manual
BF-6 |
Concept Pro AIR3016 Security Camera Operation & user’s manual
AIR3016 |
Concept Pro CBP6314DNIR Security Camera Operation & user’s manual
CBP6314DNIR |
JAI CV-S3200 Security Camera Operation manual
CV-S3200 |
Axis M1013 Security Camera Owner's manual
M1013 |
Concept Pro CBP360-HD Security Camera Operation & user’s manual
CBP360-HD |
FLIR Navigator II Security Camera Operator's manual
Navigator II |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Panasonic | TX-W32D5DPF | Operating instructions manual | panasonic/tx-w32d5dpf-SVV.pdf | 17 Apr 2023 | 35 | |
2 | Long range system | TX-7470-C232 | Operation & user’s manual | long-range-system/tx-7470-c232-6W3.pdf | 12 Jul 2023 | 11 | |
3 | American DJ | UC3 wireless | Product information | american-dj/uc3-wireless-521.pdf | 07 Dec 2023 | 2 | 0.5 Mb |
4 | Bella | 14413 | Instruction manual | bella/14413-DMS.pdf | 16 Sep 2022 | 28 | |
5 | Harmony | Folding Travel Booster Car Seat | Instruction manual | harmony/folding-travel-booster-car-seat-1PB.pdf | 03 Jul 2023 | 63 | |
6 | RuggedCom | RUGGEDSWITCH RS900G | Installation manual | ruggedcom/ruggedswitch-rs900g-951.pdf | 23 Mar 2024 | 17 | 1.61 Mb |
Abus
IPCB42500 / IPCB42550 User manual Software Version 11/2015 English translation of the original German user manual. Retain for future reference. IPCB42500 IPCB42550
…
IPCB42500(49 pages) |
urmet domus
DS1092-079A MINITELECAMERA ALTA DEFINIZIONE DAY & NIGHT CON LED IR HI RESOLUTION DAY & NIGHT MINI CAMERA WITH IR LED HOCHAUFLÖSENDE TAG & NACHT KAMERA MIT IR LED Sch./Ref./Typ 1092/205 MANUALE D’USO INSTRUCTIONS GEBRAUCHSANLEITUNG Mod.1092
…
1092(16 pages) |
Planet
Dual Mode CCD Dome Internet CameraKey FeatureData Sheet1Simultaneously provides MPEG-4 and M-JPEG video streaming, the PLANET ICA-510 is a Dual Mode CCD Dome Internet Camera which uses high resolution 1/3-inch CCD sensor for capturing color images. Equipped with network and analog video output interfaces make the ICA-510 a flexible viewing and recording impl …
ICA-510(2 pages) |
Videoline
Videoline Super Nite-Vision OSD B/W CCD Camera MC-2620 series MC-2620C/2620E MC-2621C/2621E MC-2622C/2622E INSTALLATION INSTRUCTIONS To ensure optimum performance of this CCD camera, please carefully read all the instructions before installing. Incorrect operation or setting may result in inferior picture quality.
…
MC-2620C(16 pages) |
i3
1080P (2MP) Indoor IR HD Analog Dome w/ Motorized LensDMAIN MENU > VIDEO FORMAT2M30 (default) = NTSC video format.2M25 = PAL video format.MAIN MENU > EXPOSUREEXPOSURE setup contains settings for EXPOSURE MODE and AGC. • EXPOSURE MODE: Set camera exposure mode to GLOBAL (default), BLC, WDR, or HLC.GLOBAL (default)Global (normal) exposure mode calibrat …
Am51(4 pages) |
Honeywell
C1 Wi-Fi Security CameraQuick Installation GuideM37745Download the Honeywell Home appNOTE: Have your WiFi password available and confirm your router communicates at 2.4 GHz before installation.1 Make sure bluetooth is enabled on your mobile device.2 Search for Honeywell Home in the App Store or Google Play.3 Download the Honeywell Home app.GET IT ON
…
Lyric C1(36 pages) |
Furuno Monitor FEA-2107Furuno Monitor FEA-2107 Operator's manual FEA-2107, 664 |
HP Monitor 7.1Monitor Quick user manual (HP 7.1) 7.1, 8 |
Amana Refrigerator Bottom Freezer RefrigeratorRefrigerator Owner's manual (Amana Bottom Freezer Refrigerator) Bottom Freezer Refrigerator, 180 |
Central Pneumatic Paint Sprayer 86Central Pneumatic Product Manual: 86 PDF Set up and operating instructions manual - A45NRA 86, 13 |
Panasonic Adapter BL-PA100KTBL-PA100KT (Adapter ePDF User Manual, #77N3UJ) BL-PA100KT, 20 |
CLASSÉ AUDIO CD Player CDP-100CLASSÉ AUDIO Product Guide: CDP-100 PDF Owner's manual - MP2WO3 CDP-100, 32 |
Polk Audio Headphone Ultra Focus 8000Polk Audio Headphone Ultra Focus 8000 Owner's manual Ultra Focus 8000, 16 |
Sony CD Player CFD-G35 - Cd Radio Cassette-corder#ZA3O73 CFD-G35 - Cd Radio Cassette-corder: Sony CD Player Owner Documentation CFD-G35 - Cd Radio Cassette-corder, 2 |
GE Mixer 169204Mixer Owner's manual (GE 169204) 169204, 11 |
Vivotek Security Camera CC8130Security Camera #VR4657 CC8130, 8 |
Uniden Transceiver Cell PhoneUniden Cell Phone Guide (Reference manual), @7C9934 Cell Phone, 31 |
Pioneer Amplifier CT-F10Pioneer CT-F10 Amplifier Operating instructions manual CT-F10, 40 |