Manualios.com

Tarantula AL.1 Installation Manual

Tarantula AL.1 Manual Online:

3.3, 2385 votes
Tarantula AL.1 User Manual
Tarantula AL.1 User Guide
Tarantula AL.1 Online Manual

Text of Tarantula AL.1 User Guide:

  • FCC ID NOTICE This device complies with Part 15 of the FCC rules. Operation is s ubject to the following conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including inte rference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the part responsible for

  • AL.1 INSTALL MANUAL WHITE: 16 AwgPOSITIVE PARK LIGHT OUTPUT (+15amp) SYSTEM CHASSIS GROUND INPUT RED: 20 AwgCONSTANT 12 VOLT INPUT OUTPUT TO ACTIVATE SIREN (+2amp) RED/WHITE: 22 AwgOUTPUT FOR TRUNK RELEASE (-) AUX 1 OUTPUT (-) STARTER DISABLE (-) WHEN ARMED DOME LIGHT SUPERVISION WHITE/GREEN: 22 Awg SECOND UNLOCK OUTPUT (-) BLUE: 22 AwgINPUT FOR HOOD OR TRUNK SWITCH (-) GREEN: 22 AwgINPUT FO

  • Tarantula AL.1, OUTPUT TO ACTIVATE SIREN (+2amp) AUX 1 OUTPUT (-) STARTER DISABLE (-) WHEN ARMED DOME LIGHT (-) WHEN DISARMED (30sec) WHT/GRN SECOND UNLOCK OUTPUT (-) BLUEINPUT FOR HOOD OR TRUNK SWITCH (-) GREENINPUT FOR NEGATIVE DOOR PIN SWITCH PURPLEINPUT FOR POSITIVE DOOR PIN SWITCH YELLOWSWITCHED IGNITION INPUT (+) WHT/BLUE ORANGE BLK/WHT BROWN WHITEPOSITIVE PARK LIGHT OUTPUT (+15amp) SYSTEM CHASSIS GROUND INPUT RED CONSTANT 12 VOLT INPUT (20AMP) BLACK 10 PIN CONNECTOR 3 PIN POWER CONNECTOR SYSTEM PROGRAMMING - Menu 1 INSTALL MANUAL SYSTEM WIRING OUTPUT FOR TRUNK RELEASE (-) RED/WHITE AL.1

  • Tarantula AL.1, Pin 1- Brown Wire- Siren Output (3amp Maximum) Connect this wire to the brown or red wire from the alarm siren. Pin 2- Red/White Wire- Trunk Release This output activates for 0.75 sec when the Trunk Button is held for 5 seconds. Pin 3- White/ Blue Wire- Aux 1 (-250ma Output) This output is activated by pressing the star button on the remote for a min of 3 seconds. Pin 4- Orange Wire- Ground When Armed (-250ma Output) This wire switches to ground when the lock button is pressed. This output can be used for a external starter disable or to activate such devises as a window ro

  • Tarantula AL.1, 3 PIN KEYLESS CONNECTOR BLUENEGATIVE OUTPUT FOR UNLOCK RED12+ OUTPUT FOR DOOR LOCK MODULE NEGATIVE OUTPUT FOR LOCK GREEN System Reset will set all program menu’s to the default factory setting. SYSTEM RESET Cycle the Ignition Key - ON/OFF ON/OFF ON (Leaving the key ON) 1 chirp confirms program mode entered followed by 3 chirps confirming that the system has reset. 1 - 2 - 3 - Press and release the program switch (The siren will chirp) **If the siren does not chirp repeat step 1-2. Hold the program switch until the siren chirps 3 times. SYSTEM PROGRAMMING - Menu 1 INSTALL MANU

  • Tarantula AL.1, 3 PIN KEYLESS CONNECTOR This connector is used when installing the optional keyless entry feature. If the door lock type of the vehicle is not negative you may need to install a voltage inverter, relays or a door lock module to install this feature. Pin 1- Green Wire- Negative Lock Output Connect to lock wire from the switch on vehicles with a negative type switch. **LOW CURRENT ONLY** Pin 2- 12volt Output for Door Lock Module This output will supply 12volts for a plug-in type door lock module. Do not use this input to power- up relays **LOW CURRENT ONLY** Pin 3- Blue Wire- Negative Unlock Output Connect to lock wire from the switch on v

  • Tarantula AL.1, SETTING # LED/ SIREN 1 2 3 VALET SETTINGS SECURE VALET 15 SECONDS STANDARD VALET 8 SECONDS OPTION 3 3 CHIRPS OPTION 1 1 CHIRP OPTION 2 2 CHIRPS PARK LIGHT OUTPUT AUX 1 OUTPUT 30 SECOND ON FOR DISARM 0.75 SEC PULSED OUTPUT N/A LATCHED IGNITION ON RESET NORMAL OPERATION ACTIVE WHILE BUTTON HELD SETTING DESCRIPTION SETTING # LED/ SIREN 1 2 3 4 5 6 7 IGNITION AUTO-LOCK IGNITION AUTO-LOCK & UNLOCK ENABLED IGNITION AUTO-LOCK ONLY OPTION 3 3 CHIRPS IGNITION AUTO-LOCK DISABLED OPTION 1 1 CHIRP OPTION 2 2 CHIRPS SIREN SETTINGS DOOR LOCK OPTIONS DOOR LOCK PULSE TIMES SHOCK SENSOR SETTINGS PASSIVE ARMING PASSIVE DOOR LOCKS SIREN CHIRPS DISABLED DOUBLE UNLOC

  • Tarantula AL.1, TRANSMITTER PROGRAMMING ENTERING REMOTE PROGRAM MODE The system can lean up to 3 different transmitter codes. Each remote to be used MUST be programmed together during the same sequence. For security, when a new remote is programmed all previous remote’s are deleted. Please see remote operation chart for information on using Second Car / Pad Lock Operations. Press and HOLD the valet switch, siren will chirp ONCE (If siren does not chirp repeat step 1) CONTINUE TO HOLD until siren chirps 5 times Press & Release LOCK button on 1st Remote to be Programmed for Normal Operation If remote(s) are to be programmed for "PADLOCK" skip and goto step 6 Press & Release

  • Tarantula AL.1, SHOCK SENSOR ADJUSTMENTS 3 CHIRPS Press and HOLD the Lock and Unlock buttons Hold both buttons until the siren chirps to confirm the shock sensor setting. (1-10 chirps) NOTE- If no buttons are pressed the Shock Sensor Adjustment Mode will automatically time out after 8 seconds. Each time the lock button is pressed and released the sensitivity will be INCREASED by 1 level. This is confirmed by a series of park light flashes and siren chirps. 1 Flash / Chirp is the least sensitive setting 10 Flashes / Chirps is the most sensitive setting Each time the unlock button is pressed and released the sensit

  • Tarantula AL.1, SYSTEM PROGRAMMING - Menu 1 INSTALL MANUAL DIAGNOSTICS AL.1 ALARM STATUS / DIAGNOSTICS ALARM STATUS / DIAGNOSTICS LED FLASHES OUTPUT DIAGNOSTICS 2 LOCK OUTPUT OVERLOAD 3 UNLOCK OUTPUT OVERLOAD 4 TRUNK OUTPUT OVERLOAD 5 STARTER DISABLE OVERLOAD 6 NOT USED 7 AUX 5 OUTPUT OVERLOAD 8 2ND UNLOCK OUTPUT OVERLOAD If the alarm system is triggered, the system will retain in memory the cause of the trigger. When disarming the alarm, the siren will chirp 3 times to indicate the alarm had been triggered. The system’s LED will also flash in pulses to indicate which input triggered the alarm. *LED status will be cleared when the ignition is turned ON. For proper memory clearing, insure to connect

Related Products and Documents (Car Alarm):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 KERAFLO AYLESBURY KB Installation manual keraflo/aylesbury-kb-141.pdf 16 Dec 2022 10
2 Tyco Keystone F792 Specification sheet tyco/keystone-f792-9CR.pdf 13 Apr 2023 6 0.44 Mb
3 Marzocchi MAX COMP + ETA - 105 Manual  marzocchi/max-comp-eta-105-P7N.pdf 11 Feb 2023 45
4 CPS VG200 Owner's manual cps/vg200-HSA.pdf 17 Apr 2023 4
5 Nitto Kohki AO-5575 Instruction manual nitto-kohki/ao-5575-35U.pdf 13 Nov 2022 24
6 IMG STAGE LINE MEGA-DSP 08 Instruction manual img-stage-line/mega-dsp-08-W3D.pdf 01 Jul 2022 21

Similar Resources:

  • ROEL

    Alcar H51

    (8 pages)
    User’s ManualDOC. 50302/16.08.00 / VERSION 1.0Auto Alarm SystemRomano Electro Intl S.A.27-29 Calimachi str., 72266, Bucharest,Tel.:40-1-242.20.20, Fax:40-1-242.20.30,E-mail: [email protected], www.roel.ro …
  • TriMark

    e-FOB

    (20 pages)
    e-ASK electronic Access Security Keyless-entry ee--FOBFOB / e/ e--PADPAD Consumer ManualConsumer Manual FCC ID: TV2EFOB1FCC ID: TV2EFOB1 (UM12 ~ 22271-02) …
  • Ultra Start

    35 SERIES

    (16 pages)
    -The system must be placed into Service Mode before any service work is started on the vehicle. It isthe sole responsibility of the vehicle owner to ensure that this is done. The manufacturer accepts noliability or responsibility for accidental starting of the vehicle.- CARBON MONOXIDE - Never Start in an Enclosed Building (Garage, Carport etc...)- The Hood …
  • Code Alarm

    CA2LED5

    (12 pages)
    1CA2LED5 / AS9234E 4280852 Owners rev A.IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the conguration of some vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.PROFESSIONALSERIESOwner’ …
  • Audiovox

    PRO 9644

    (10 pages)
    Model PRO 9644Owner’s Manual3 Button Remote Security System with Starter DisableIMPORTANT ! In order to provide the highest possible level of security to your vehicle, thissystem is equipped with selectable manual override circuitry. It is possible that you will need tomanually override your security system if the transmitter becomes lost, or inoperative …
  • Black Widow Security

    BW2900R2

    (16 pages)
    1Standard Features:Two 4-Button Remote TransmittersStatus indicator (LED)Valet / override switchMulti-tone siren (120dB)Dual stage impact detectorRemote panicRemote chirp mute Remote sensor bypassActive or passive armingOptional Features:Starter disable Flashing parking lightsKeyless entryRemote trunk or hatch releaseIlluminated entryHood and trunk protectio …

Comments, Questions and Opinions: