Manualios.com

Tomahawk TW-9010 Operation & User’s Manual

Tomahawk TW-9010 Manual Online:

3, 2010 votes
Tomahawk TW-9010 User Manual
Tomahawk TW-9010 User Guide
Tomahawk TW-9010 Online Manual

Text of Tomahawk TW-9010 User Guide:

  • Tomahawk TW-9010, TOMAHAWK TW-9010 CONTENTS USER MANUAL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 1 2 3 4 5 6 System main features Remote control trinkets LCD features Arming mode Arming with siren disabled Automatic arming and re-arming Immobilizer features Disarming Opening/closing doors with engine working Two-step door opening/channel 3 Remote engine start-up Remote engine cut-off Turbo timer Warming-up engine to specified temperature Daily (1, 2, 4, 12-hour) automatic start-up R

  • Tomahawk TW-9010, TOMAHAWK TW-9010 6. Auto Arming and Re-arming If the auto arming function is enabled, then: with ignition OFF, after all doors are closed the system will alert with 1 long “CHIRP” and will switch security mode ON 10 sec later (see Programming Table). Auto re-arming function is always enabled in the case when after disarming none of the doors open within 30 sec. 7. Immobilizer Mode The immobilizer mode is enabled automatically 30 sec after ignition cut-off (see Programming Table). LED indica

  • TOMAHAWK TW-9010 To disable this function, press buttons and . Parking lights will flash 2 times and siren will sound 2 “CHIRPS” to confirm disabling the function. LCD will hide icon and a melody will play. Note: Automatic engine warming-up to specified temperature should be made six times per two hours as maximum. Temperature for automatic engine wa

  • Tomahawk TW-9010, TOMAHAWK TW-9010 3. LCD Features Fig. 3 1. -- security mode indication. 2. – “silent security” mode indication 3. – closed central lock indication 4. -- open central lock indication 5. – open door(s) indication 6. – open hood indication 7. – open boot indication 8. - parking lights flashing indication 4

  • Tomahawk TW-9010, TOMAHAWK TW-9010 6 PIN Remote Start-up Power Socket 1. Blue wire – central contact for central lock opening relay 2. Blue and grey wire – normally open contact for central lock opening relay 3. Blue and black wire – normally closed contact for central lock opening relay 4. Green wire - central contact for central lock closing relay 5. Green and grey wire – normally open contact for central lock closing relay 6. Green and back wire – normally closed contact for central lock closing relay 18 PIN Main

  • Tomahawk TW-9010, TOMAHAWK TW-9010 Engineering data Rated voltage +12V Current consumption 15mA Allowable current: 6 PIN remote start-up power socket In power supply circuit thick red wire 30A (limited with fuse) In power supply circuit thin red wire 10A (limited with fuse) IGN 1, “+” 30A (yellow wire) IGN 2, “+” 30A (green wire) IGN 3, “-” 300mA (black and red wire) Starter wire, “+” 30A (black and yellow wire) 6 PIN central lock connection socket In contact relay circuit for central lock control 20A (l

  • Tomahawk TW-9010, TOMAHAWK TW-9010 17. Remote Boot Opening To remotely open the boot, press and hold button . Parking lights will flash 3 times to confirm the boot opening. LCD will display icon . ATTENTION! This function requires auxiliary connection while installation . 18. 2-nd Auxiliary Channel To enable this function, press and hold button . Parking lights will flash 1 time, siren will sound 1 “CHIRP” to confirm enabling the function. ATTENTION! This function requires au

  • Tomahawk TW-9010, TOMAHAWK TW-9010 21. - hand-brake disengage indication 22. - started engine indication 23. - battery level indication 24. - timer switch-on indication 25. - alarm-clock switch-on indication 26. - clock 27. - temperature measurement units (C or F) 4. Arming Mode To arm a car, I is necessary to press button 1 time. Parking lights will flash 1 time; siren will sound 1 “CHIRP” to confirm entry in security mode, doors and windows will close (if connected). LCD will display icons and . In case when siren sounds 3 “CHIRPS”, it means that the system detected and disabled a defective zone (open door, hood, boo

  • Tomahawk TW-9010, TOMAHAWK TW-9010 1 “CHIRP” and flash – function enabled 2 “CHIRPS” and flashes – function disabled 7. Switch ignition OFF. NOTE: If the daily auto start function is enabled, the engine will start up immediately after ignition is switched OFF. Use your remote control trinket to stop the engine. 27. Emergency Arming/Disarming 1. For emergency arming: A) Switch ignition ON (engine must not be started) B) Press button “Override” 8 times C) Switch ignition OFF Parking lights will flash 1 time and siren will sound 1 �

  • TOMAHAWK TW-9010 28. Remote Start-up Preparation for Cars with Manual Transmission To ensure capability of remote start-up for cars with manual transmission, the gear lever should be in neutral position. Before stopping car engine, perform the following procedures: 1. Enable car hand-brake (engine should be started) 2. Press button , LCD will display icon , and a melod

  • Tomahawk TW-9010, TOMAHAWK TW-9010 ATTENTION! Remote engine start-up cannot be done in the case if: 1. Gear lever is not in neutral position. 2. Ignition switched ON. 3. The hood is open. 4. The hand-brake is not engaged. In any of these occasions, siren will sound 4 “CHIRPS” at a remote start-up attempt. 13. Remote Engine Stop In the case when the engine was started using remote start-up, you can stop it by pressing button . Parking lights will flash 4 times; siren will sound 4 “CHIRPS”. LCD will hide icon and a melody will play. 14. Warming-up Engine to Specified Temperature Tomahawk provides for an auxiliary temperature sensor for installation under the ho

  • Tomahawk TW-9010, TOMAHAWK TW-9010 5. Connection of Central Lock TOMAHAWK TW-9010 has in-built power relays for central lock control. Wiring for connection of central lock is made in a separate six-pin socket. Wire colours and wiring diagrams are shown in diagrams 1-4. ATTENTION! Please note that impulse duration for central lock control is a programmable function. 6. Setting Shock Sensor S etting is the last installation stage of TOMAHAWK TW-9010 alarm system. Set shock sensor sensitivity to minimum. Gradually increase sensitivity and knock the car body with your palm to check triggering threshold. ATTENTION! Excess sensitivity may

  • Tomahawk TW-9010, TOMAHAWK TW-9010 35. Description of Programmable Functions 1. Time allotted for engine running after remote start-up: 5/10/15/20 min. 2. Engine temperature when automatic warm-up is switched ON (if the function is enabled): -5 o / -10 o /-20 o /30 o C. 3. Time for starter operation when remote start-up function is enabled: 800/1200/1800/3000 ms. Time for the first start-up attempt is specified. If first attempt fails, the system will increase time for each three subsequent attempt by 200 msec. ATTENT

  • Tomahawk TW-9010, TOMAHAWK TW-9010 On triggering the shock sensor main zone (strong shock), the system will enable alarm mode for 25 sec. LCD will display icon and an alarm signal will sound. On triggering any other zone, the system will enable alarm mode for 30 sec. LCD will display an icon corresponding to the triggered zone (see page 3) and an alarm signal will sound. ATTENTION! To disable the alarm signal, press button . This will cut the alarm mode off but the car will remain secured. 22. “Panic” Mode To enable t

  • Tomahawk TW-9010, TOMAHAWK TW-9010 INSTRUCTIONS FOR INSTALLATION 1. Basic Installation Principles TOMAHAWK TW-9010 vehicle alarm system has a classic connection arrangement. First of all, before installation disable vehicle power system (disconnect “–“ battery terminal). To choose places for alarm system units, follow the principles as below: - Secrecy of installation - Absence of heat and moisture emitting sources near the units - Allow for minimal mutual interference between standard vehicle electronics and alarm units ATTENTION! Emitting antenna shou

  • Tomahawk TW-9010, TOMAHAWK TW-9010 3. Wire Connections 6 PIN Remote Start-up Power Socket 1. Black and yellow wire – starter switch-on wire (+12V). This is an output signal +12V to starting relay. It is connected to ignition lock wire where +12V appears in the “Starter” key position. This signal is for engine start-up. Connect this wire to blocking relay. 2. Blue wire –An output signal +12V ACC – auxiliary equipment. It is connected to ignition lock wire where +12V appears in the “ACC” and “Ignition ON” key posi

  • TOMAHAWK TW-9010 5. Yellow and red wire – 2nd auxiliary channel wire (-300mA). 6. Grey and black wire – input for tachometer wire or oil pressure sensor. Connect to tachometer signal wire or oil pressure sensor wire (programmable). 7. Blue and red wire – “+” input for door sensor. 8. Orange and white wire - “-” input for boot sensor. 9. Violet wire - “Ant

  • Tomahawk TW-9010, TOMAHAWK TW-9010 Version 2 – Doors are automatically locked 10 sec after ignition ON and open immediately after ignition OFF. Version 3 – Doors are automatically locked 30 sec after ignition ON and open immediately after ignition OFF. 12. Auto arming. Version 1 –OFF; Version 2 – ON without locking doors Version 3 – ON with locking doors 13. Cabin lighting delay count. The system will secure doors after the specified period (1 sec/15 sec/30 sec/45 sec) after pressing bu

  • Tomahawk TW-9010, TOMAHAWK TW-9010 18 PIN main socket Blocking relay contacts 40A Blocking relay service output, “-“ 300mA (black and yellow wire) Siren power output, “+“ 2A (grey wire) Auxiliary channel 1 output, “-“ 300mA (yellow and black wire) Auxiliary channel 2 output, “-“ 300mA (yellow and red wire) Auxiliary channel 3 output, “-“ 300mA (yellow and blue wire) Size lights power supply outputs, “+“ 7.5A (green-black and green-yellow wires, limited with fuses) Output to cabin light, “-“ 300mA (blue wire)

  • Tomahawk TW-9010, TOMAHAWK TW-9010 6. The system will automatically exit the trinket programming mode, if it does not receive signals from the trinket within 6 sec. ATTENTION! All un-programmed trinkets will be erased from the memory. 30. LED Indicator Operation Modes The system displays its status using LED indicator when car ignition is switched OFF. System status Number of flashes 1. Remo te start - up mode and Immobilizer mode Glowing continuously 2. Car disarmed Disabled 3. Car armed 1 flash 4. Daily auto start mode 2 flashes 5. Auto wa

Related Products and Documents (Car Alarm):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Pilz PNOZ mmc2p Operating manual pilz/pnoz-mmc2p-6UR.pdf 05 Aug 2022 25
2 Bosch MEK 7000 UC Use and care manual bosch/mek-7000-uc-GG4.pdf 24 Oct 2023 37
3 Samsung SGH-E690 Operation & user’s manual samsung/sgh-e690-2KO.pdf 27 Aug 2022 141
4 Medeli MC-49 Owner's manual medeli/mc-49-2P4.pdf 16 Jun 2023 24
5 Sony VGN-FS660 Specifications sony/vgn-fs660-35P.pdf 22 May 2023 2
6 AE RC10 GRAPHITE Operation & user’s manual ae/rc10-graphite-77V.pdf 17 Dec 2023 41

Similar Resources:

  • iDataLink

    Maestro RR

    (106 pages)
    NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certifi ed technician. Logos and trademarks used here in are the properties of their respective owners.WARNINGPressing the printer icon or “quick printing” this document will printall of the guides in this compilation.Open the Bookmarks menu and find your veh …
  • Brazel's RV Performance

    UltraTrac UTF53V8R

    (3 pages)
    UTF53V8R InstructionsFord F-53 – 14,000, 16,000 & 18,000 GVW Motor Home Chassis Rear Bar Page 1 of 3Bolt Size Grade 5 Grade 81/4” 10 145/16” 19 293/8” 33 477/16” 54 781/2” 78 1195/8” 154 2303/4” 257 380Torque in Foot-Pounds for Inch Bolts Torque in Foot-Pounds for Metric Bolts Bolt Size Grade 8.8 Grade 10.96MM 6 88MM 16 2210MM 31 4012MM 5 …
  • Webasto

    Thermo Top E

    (35 pages)
    WARNING!Hazard warning:Incorrect installation or repair of Webasto heating systems may cause a fire or result in the emission of carbon monoxide, which can be fatal. Serious or fatal injuries can be caused as a result.Specialist company training, technical documentation, specialised tools and equipment are required to install and repair Webasto heating and c …
  • ENFORCER

    SLI 840

    (12 pages)
    SECO-LARM® U.S.A., INC.16842 Millikan Avenue,Irvine, California 92606FILE: MANUALS\MoSLI840.P65/NOV2000ORDER PART# 760-883-2/913SLI 840 / SLI 840C (315 MHz)SLI 840-4 / SLI 840C-4(433.92 MHz)Remote ControlledKeyless Entry System with AlarmENFORCER®OWNER'S MANUAL …
  • BSM

    Saturn M5

    (7 pages)
    “БСМ” ООД, 1784 София, бул. “Цариградско шосе” 137, тел.: 02 / 974 4340, 974 5029, 974 3034, факс: 02 / 974 43 42, GSM: 0899 176 734, 0888 253 448, e-mail: [email protected]/7SATURNM5CAPABILITIES-dynamic code-optional alarm signals*-optional signals for arming/disarming*-four buttons remote transmitter-doub …
  • Fortin

    EVO-ONE

    (7 pages)
    1-Page_enteteWARNINGATTENTION* HOOD PINHOOD STATUS : THE HOOD PIN SWITCH (INCLUDED)MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN. CONTACTDE CAPOTSECURITY STICKERAUTOCOLLANT DE SÉCURITÉMANDATORY INSTALL | INSTALLATION OBLIGATOIRENotice: the installation of safety elements are mandatory. The hood pin and the sticker are essenti …

Comments, Questions and Opinions: