Manualios.com

Cisco 7030 Installation Manual

Cisco 7030 Manual Online:

3.75, 730 votes
Cisco 7030 User Manual
Cisco 7030 User Guide
Cisco 7030 Online Manual

Text of Cisco 7030 User Guide:

  • CHAPTER 2-1 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 2 Camera Installation This chapter provides information and instructions for installing the Cisco Video Surveillance 7030 IP Camera, and includes the following topics: • Installation Guidelines, page 2-1 • Warnings Before Installation, page 2-1 • Installing the IP Camera

  • Cisco 7030, 2-7 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 Chapter 2 Camera Installation Installing the IP Camera with a Vandal Resistant Enclosure c. Feed the power cable through the waterproof connector (F --> E --> D --> B --> A). Be sure to feed enough power cable length through the waterproof connector to connect the power cable to the GPIO block. Note There are 8 holes on the seal (D), and the widest holes with a crack on the side are specific for power cables. d. Feed the I/O cables through the waterproof connector (F --> E --> D --> B --> A). B

  • Cisco 7030, Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Cisco Video Surveillance 7030 IP Camera Installation Guide Text Part Number: OL-28692-01

  • Cisco 7030, 2-10 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 Chapter 2 Camera Installation Installing the IP Camera with a Vandal Resistant Enclosure • After completing the initial setup, use the IP camera user interface to adjust the focal length and zoom factor. For more information, see the “Adjusting the IP Camera Focus and Zoom” section on page 4-3.

  • Cisco 7030, CHAPTER 4-1 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 4 Camera Management This chapter provides information and instructions for managing the Cisco Video Surveillance 2620 IP Camera, and includes the following topics: • Understanding the IP Camera User Interface, page 4-1 • Adjusting the IP Camera Focus and Zoom, page 4-3 • Powering the IP Camera On or Off, page 4-4 • Resetting the IP Camera, page 4-4 • Viewing Live Video, page 4-5 Understanding the IP Camera User Interface After you log in to the IP camera, you can access the IP camera windows and perform a variety of administrative and user procedures. T

  • Cisco 7030, 2-2 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 Chapter 2 Camera Installation Warnings Before Installation • Do not place the IP Camera around heat sources, such as a television or oven. • Refer to your user’s manual for the operating temperature. • Keep the IP Camera away from direct sunlight. • Do not place the IP Camera in high humidity environments. • Do not place the IP Camera on unsteady surfaces. • Do not touch the IP Camera during a lightning storm.

  • Index IN-3 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 W warnings before installation 2-1 waterproof connector 2-6 Z zoom accessing controls 4-8 zoom controls 4-8

  • Cisco 7030, 4-3 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 Chapter 4 Camera Management Adjusting the IP Camera Focus and Zoom Adjusting the IP Camera Focus and Zoom To adjust the IP camera focus and zoom, perform the following steps while viewing video from the camera. For information about viewing video, see “Viewing Live Video” section on page 4-5. Procedure Step 1 Login to the IP camera. The Home window appears. Step 2 Click the View Video link. The Camera Video & Control window appears. Step 3 Verify that the field of view is correctly set. Step 4 Click the Focus/Zoom togg

  • Cisco 7030, 2-5 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 Chapter 2 Camera Installation Installing the IP Camera with a Vandal Resistant Enclosure Step 5 Perform the following steps to install and connect an RJ45 Ethernet cable. Note We recommended using 24AWG (0.51 mm) gauge cable. a. Drill a hole on the rubber seal plug and insert an Ethernet cable (without a connector) through the opening. b. Strip about 1/2 inch (12 mm) of the sheath from the Ethernet cable. c. Use an RJ45 crimping tool to attach the Ethernet wires to a connector. When done, connect the cable to the camera’s Ethernet RJ45 socket. o O g B b G br BR 1 2 3 4 5

  • Cisco 7030, IN-1 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 INDEX A About link 4-2 ActiveX controls 4-2 B brightness 4-5 C camera See IP camera Camera Video/Control window accessing 4-5 description 4-2 displaying 4-2 connecting, to the IP camera for the first time 3-1 PC requirements for 3-1 contrast 4-6 D DHCP, obtaining IP address through 3-1 F factory reset 4-4 focus/zoom accessing controls 4-8 controls 4-8 G GPIO terminal block 2-7 H help, for IP camera windows 4-2 Home window description 4-2 displaying 4-1 HTTP, allowing access through

  • Cisco 7030, 2-9 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 Chapter 2 Camera Installation Installing the IP Camera with a Vandal Resistant Enclosure c. Rotate the IP camera to adjust the horizontal orientation until you achieve a level image. Step 10 (Optional) If the IP camera is installed in a high humidity environment, remove the wrapper from the included silica gel pack and place the pack with the camera inside the VR housing. Ensure that the silica gel pack does not obstruct the IP camera field of view. Step 11 Attach the dome cover to the camera by aligning it with the mounting holes. S

  • Cisco 7030, 3-2 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 Chapter 3 Performing the Initial Setup of the IP Camera Step 3 In the Password and Confirm Password fields of the admin row, enter a password for the IP camera administrator. You must enter the same password in both fields. The password is case sensitive and must contain at least eight characters, which can be letters, numbers, and special characters, but no spaces. Special characters are: ! " # $ % & ' ( ) * + , - . : ; <

  • Cisco 7030, CHAPTER 1-1 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 1 Overview This chapter describes the Cisco Video Surveillance 7030 IP Camera, and includes the following topics: • Introduction, page 1-1 • Package Contents, page 1-2 • IP Camera Physical Details, page 1-3 Introduction The Cisco Video Surveillance 7030 IP camera is an outdoor, high definition, professional fixed dome IP camera with industry-leading image quality and processing power. The 5 megapixel (

  • Cisco 7030, NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The Cisco implementation of

  • Index IN-2 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 powering off 4-4 powering on 4-4 tilting 4-6 windows 4-2 L live video viewing through home window 4-5 through third-party device or software 4-5 See also video log out, of IP camera 4-2 M motion detection accessing controls 4-7 controls 4-7 enabling 4-7

  • Cisco 7030, 2-6 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 Chapter 2 Camera Installation Installing the IP Camera with a Vandal Resistant Enclosure d. Press the Ethernet cable into the routing path at the bottom of the camera so that the cable will not get in the way when the metal mounting plate is attached. Step 6 (Optional) Perform the following steps to install and connect an external power cable and I/O cables for external devices: a. Disassemble the components of the waterproof connector

  • Cisco 7030, 4-4 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 Chapter 4 Camera Management Powering the IP Camera On or Off Step 7 (Optional) Click Auto Focus to have the IP camera automatically adjust its focus. To automatically adjust the focus to a particular region in the field of view, check the Specify Region check box and draw or select a region before clicking Auto Focus. Powering the IP Camera On or Off The IP camera does not include an on/off switch. You power it on or off by connecting it to or disconnecting it from a power source. When you power off the IP camer

  • Cisco 7030, 2-4 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 Chapter 2 Camera Installation Installing the IP Camera with a Vandal Resistant Enclosure Note The equipment is to be connected to a Listed class 2, limited power source. Installing the IP Camera with a Vandal Resistant Enclosure To install the IP camera to a ceiling or wall using a vandal resistant (VR) enclosure, perform the following steps. Procedure Step 1 Attach the included alignment sticker to the ceiling or wall. Step 2 Using the circle marks on the sticker, drill at least two pilot holes symmetricall

  • Cisco 7030, iii Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 CONTENTS Preface v Overview v Organization v Obtaining Documentation, Obtaining Support, and Security Guidelines v CHAPTER 1 Overview 1-1 Introduction 1-1 Package Contents 1-2 IP Camera Physical Details 1-3 General Purpose I/O Terminal Block 1-5 CHAPTER 2 Camera Installation 2-1 Installation Guidelines 2-1 Warnings Before Installation 2-1 Installing the IP Camera with a Vandal Resistant Enclosure 2-4

  • Cisco 7030, CHAPTER 3-1 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 3 Performing the Initial Setup of the IP Camera After you install IP camera as described in the Chapter 2, “Camera Installation,” or after you perform a factory reset procedure, you must access the IP camera and make initial configuration settings. These settings include administrator and root passwords, and whether the IP camera can be accessed through an HTTP connection in addition to the default HTTPS (HTTP secure) connection. To make these configuration settings, you connect to the IP camera from any PC that is on the same network as the IP ca

  • Cisco 7030, 4-2 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 Chapter 4 Camera Management Understanding the IP Camera User Interface IP Camera Windows The IP camera user interface includes these main windows: • Home window—Displays the system information that is described in Table 4-2. • Setup window—Provides access to the IP camera configuration windows. • Camera Video & Control window—Displays live video from the camera and lets you control a variety of camera and display functions. View Video Displays the Camera Video & Control

  • Cisco 7030, 1-5 Cisco Video Surveillance 7030 IP Camera Installation Guide OL-28692-01 Chapter 1 Overview General Purpose I/O Terminal Block General Purpose I/O Terminal Block Figure 1-2 shows the GPIO terminal block pin locations and descriptions. Figure 1-2 GPIO Terminal Block Pin Locations and Descriptions Note The maximum output load from pins 7 and 8 is 50mA. Pin Description 1 24 VAC 2 24 VAC 3 DI- 4 DI3+ 5 DI2+ 6 DI1+ 7 DO- 8 DO+ 87654321

More Instructions:

DOWNLOAD
DOWNLOAD

Related Products and Documents (Digital Camera):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Electrolux Nimble EL8605A Owner's manual electrolux/nimble-el8605a-G6X.pdf 22 Aug 2022 16 20.35 Mb
2 Frigidaire FFC20C4CW Factory parts catalog frigidaire/ffc20c4cw-F5Q.pdf 01 Apr 2023 7 0.17 Mb
3 Samsung ML-2240 - 23 Ppm Mono Laser Printer Manual  samsung/ml-2240-23-ppm-mono-laser-printer-4O4.pdf 21 Mar 2023 16 0.03 Mb
4 Philips Lightolier GO2 Information sheet philips/lightolier-go2-1Y5.pdf 13 Aug 2022 2 0.12 Mb
5 Clarion DB265MP Installation/wire connection manual clarion/db265mp-7W4.pdf 18 Jun 2023 2 0.2 Mb
6 Chauvet Vue I Supplementary manual chauvet/vue-i-S8A.pdf 01 Nov 2022 1 0.02 Mb

Similar Resources:

  • VistaQuest

    VQ-3005

    (1 pages)
    3 MegaPixel DigitalKeychain Cameraw/ SD Card SlotRecords Video Clip (AVI) up to 100 sec.USB power Direct Support PC Camera User-Friendly Status LCD Display 3Mega Pixel CMOS SensorF 2.8 Aperture 0.9m ~ Innity1/15~1/1500 sec. (Electronic Shutter) Auto ControlVirtual type: optical, Magnication 0.32 or higher, Coverage: 80% or higherAutoAuto2304 x 172 …
  • Sony

    MVC-FD83

    (19 pages)
    MICROFILMSERVICE MANUALDIGITAL STILL CAMERAUS ModelCanadian ModelAEP ModelUK ModelE ModelAustralian ModelHong Kong ModelChinese ModelKorea ModelMVC-FD83/FD88Tourist ModelMVC-FD88SPECIFICATIONSMVC-FD83/FD88This service manual contains informationfor Japanese model as well.Photo: MVC-FD88Ver 1.0 1999. 05 …
  • XVision

    XPB750WIR

    (16 pages)
    Before you beginModel: XPB750WIR700 TVL 120m IR CameraModel: XPB750WIR700 TVL 120m IR Camera• Please unpack the box carefully and identify that all the parts are present.• Do not cut the camera cables, this will void the warranty.• Make sure you use only the recommended power supply. Damage caused to the camera by incorrect voltage or wiring is no …
  • V-TAC

    VT-5157

    (234 pages)
    WEEE Number: 80133970 INSTALLATION INSTRUCTIONMulti-Language Manual - QR CODEPlease scan the QR code to access the manual in multiple languages.INTRODUCTION Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. …
  • Conrad

    BC-713

    (4 pages)
    Diese Bedienungsanleitung ist eine Publikation der Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).Alle Rechte einschließlich Übersetzung vorbehalten. Reproduktionen jeder Art, z. B. Fotokopie, Mikroverlmung, oder die Erfassung in elektronischen Datenverarbeitungsanlagen, bedürfen der schriftlichen Genehmigung des H …
  • TANDBERG

    FieldView

    (81 pages)
    FieldViewAdministrator GuideTANDBERG FieldView™ delivers the most innovative solution in mobile video collaboration.Featuring integrated wireless LAN, high resolution video and audio and the ability to collaborate via instant on-screen annotation—it’s the next best thing to having your experts on the scene. Its ability to access small spaces enables p …

Comments, Questions and Opinions: