Manualios.com

Westinghouse SE 3718S Safety Information Manual

Westinghouse SE 3718S Manual Online:

4.6, 1367 votes
Westinghouse SE 3718S User Manual
Westinghouse SE 3718S User Guide
Westinghouse SE 3718S Online Manual

Text of Westinghouse SE 3718S User Guide:

  • Westinghouse SE 3718S, 2-2 DESCRIPTION Figure 2-2: SE 3718S Uninterruptable Power Supply PHYSICAL DESCRIPTION The SE 3718S measures 16 in. (40.6cm) long by 6 in. (15.2cm) wide by 4 in. (10.2cm) high. Unit weight is 9.2 lbs (3.4kg). As shown in Figures 2-1 and 2-2, the SE 3718S consists of a chassis with mounting flanges at each side, and a body perforated on three sides for efficient convection cooling. Status indicators and user-serviceable parts are conveniently located on the top surface.

  • Westinghouse SE 3718S, 3-6 INSTALLATION Figure 3-6: SE 818 (all suffixes) Lock Power Connections. Typical (not inclusive) BATTERY CABLE CONNECTIONS The SE 3718S is designed to operate from a backup battery system of approximately 24V in the event of a power failure. Unlike previous designs, the requirements of the battery backup system do not depend on lock voltage settings and use either two 12-volt or a single 24-volt battery. Connections between the SE 3718S and the various battery configurations using the battery cable are shown below. NOTE Discharged batteries or batteries of the wrong type ar

  • Westinghouse SE 3718S, 1-4 INTRODUCTION INSTRUCTIONS DE SECURITE  Conserver ces instructions. Cette note contient des instructions importantes concernant la sécurité.  Une batterie peut présenter un risque de choc électrique ou de brûlure par transfert d'énergie. Suivre les précautions qui s'imposent.  Afin de réduire les risques de choc électrique, il est recommandé de ne pas démonter le coffret sauf par un technicien qualifié.  Pour le remplacement, utiliser le même type de batterie du modèle suivant (Table 1.1).  La destruction des batteries est réglementée. Consulter les code

  • DESCRIPTION 2-3 FUNCTIONAL DESCRIPTION A functional block diagram of the SE 3718S Uninterruptable Power Module is shown in Figure 2-3. The SE 3718S circuitry consists of four main functional elements as described below. Figure 2-3: SE 3718S Functional Block Diagram PRIMARY SWITCHING POWER SUPPLY CIRCUITRY The purpose of the primary switching power supply circuitry is to convert

  • INSTALLATION 3-7 Figure 3-7: Battery Connections  Single 24-Volt Standby Battery BATTERY CONNECTIONS  DUAL 12-VOLT STANDBY BATTERIES When using 12-volt batteries, the SE 3718 is connected as shown in Figure 3-8. NOTE Batteries connected in series must be the same type and fully charged. Figure 3-8: Battery Connections  Dual 12-Volt Standby Batteries

  • Westinghouse SE 3718S, TROUBLESHOOTING 4-1 SECTION 4: TROUBLESHOOTING Troubleshooting the SE 3718S in the field is limited to checking continuity of the conductors in the interface cables, analyzing probable fault conditions from the status of the LEDs, and replacing blown fuses. CUSTOMER SERVICE If a problem with an SE 3718S cannot be rectified by replacing a faulty cable, interface wiring, or fuse, call WSE Customer Support for a return authorization. Units returned without a return authorization cannot be accepted. Return units to: Westinghouse Security Electr

  • Westinghouse SE 3718S, INTRODUCTION 1-3 SAFETY INSTRUCTIONS  Save these important safety instructions.  CAUTION: A battery can present a risk of electrical shock or burn from high short-circuit current. Observe proper precautions.  When replacing batteries, use the same battery number and type (Table 1-1).  Proper battery disposal is required. Refer to local codes for disposal regulations. SICHERHEITVORSCHRIFT  Bitte lesen und aufbewahren.  Auf keinen Fall die Ventilationslöcher absperren. (Hitzestau).  Einzelteile sollen nur von qualifiziertem Personal ausgewechseld wirden.  Die Batterien k

  • Westinghouse SE 3718S, SE 3718S UNINTERRUPTABLE POWER SUPPLY III LIMITED WARRANTY Westinghouse Security Electronics (WSE) warrants to the original user the equipment manufactured by WSE as described herein to be free from defects in material and workmanship for a period of one year from the date of purchase by such user or fifteen (15) months from the date of shipment from the factory, whichever is sooner (command key / magnetic stripe card warranties differsee below), provided: I WSE has been notified within such period by return of any alleged defective equipment, free and clear of any liens and encumbrances to WSE or its authorized dealer at the address specified, transportation prepaid; and II the equipme

  • Westinghouse SE 3718S, 2-4 DESCRIPTION SECONDARY SWITCHING POWER SUPPLY The secondary switching power supply converts and distributes power from either the primary switching power supply or the backup battery to all output terminals of the 3718S. CONTROL AND INDICATORS CIRCUITRY The main function of the control and indicator circuitry is to sense and control the operation of the rest of the power supply. Additionally, it reports on important power supply conditions either by status indicators on the top panel or by sending signals directly to the ACU. The conditions reported to the status indicators on the front panel include: The presence of AC in

  • Westinghouse SE 3718S, 1-2 INTRODUCTION SYSTEM APPLICATIONS The SE 3718S provides sufficient power to run an access control system consisting of the following components:  One 700- or 800-series ACU.  Up to eight multiple switch monitors (SE774, SE774A) or eight door switch monitors (SE770).  Up to eight analog proximity sensors.  A 24-volt backup battery.  One SE 778 / 778A annunciator/control module powered by the ACU in 800-series systems.  One modem (or similar accessory).  Up to eight WSE provided RS-485 communication devices.  Several low-current locking devices or similar accessories (see below). T

  • Westinghouse SE 3718S, INSTALLATION 3-1 SECTION 3: INSTALLATION LOCATION AND MOUNTING IMPORTANT The suitability of the use of flexible cord per CEC rule 4-010 is to be determined by the local inspection authority having jurisdiction. L'emploie d'un cordon souple selon l'article 4-010 de CCE première partie doit être soumis à l'approbation des autorités locales d'inspection. The length of the ACU power cable is 6 feet (1 M) and the SE 3718S position relative to the ACU must be within this limit. The SE 3718S can be

  • Westinghouse SE 3718S, DESCRIPTION 2-5 FUSES +10V 2A T/SB System Power (ACU) +20V 1A T/SB System Power (ACU) -18V 1A T/SB System Power (ACU) 24V 1A T/SB System Power (RS-485) 12V AUX. 1A T/SB Aux. Power BATTERY 10A T/SB Battery CONNECTORS SYSTEM POWER 14-pin circular. Provides all power needed by an ACU. BATTERY 4-pin circular. Provides power to and from the backup battery. AUX. POWER 4-pin Phoenix. Provides 12V of auxiliary power for use with optional, user- specified equipment. LOCK POWER 3-pin Phoenix. Provides either 12V or 24V, switc

  • Westinghouse SE 3718S, II SE 3718S UNINTERRUPTABLE POWER SUPPLY SAFETY INSTRUCTIONS (See Section 1) SICHERHEITVORSCHRIFT (Siehe Kapitel 1) INSTRUCCIONES DE SEGURIDAD (Mire Seccion 1) INSTRUCTIONS DE SECURITE (Voir Section 1) NOTICE The SE 3718S Uninterruptable Power Module manufactured by Westinghouse Security Electronics has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequenc

  • Westinghouse SE 3718S, 4-2 TROUBLESHOOTING TABLE 4-1: SE 3718S TROUBLESHOOTING GUIDE SYMPTOM PROBABLE CAUSE REMEDY AC ON indicator does not (1) No AC power to unit. (1) Check AC line; verify that power cable come on when circuit (2) Circuit breaker has tripped plug is plugged fully into power breaker is placed in the on off line. connector. position. (3) Power supply is faulty. (2) Reset circuit breaker. If it continues to trip, call WSE for disposition. BATTERY CONNECTED (1) Power supply does not recog- Wait 15 seconds: It takes several seconds and BATTERY FULL nize a battery is present. for the unit to detect a battery. Check indicators are out; all othe

  • DESCRIPTION 2-1 SECTION 2: DESCRIPTION The SE 3718S Uninterruptable Power Supply (Figures 2-1 and 2-2) provides the requisite input AC and DC power for the WSE 700- and 800-series ACUs. SE 3718S Uninterruptable Power Supply

Related Products and Documents (UPS):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Zanussi ZFU219WO Operation & user’s manual zanussi/zfu219wo-24C.pdf 01 Oct 2023 104
2 Sony WM-EX500 Operating instructions sony/wm-ex500-7Z9.pdf 06 Sep 2022 2 0.14 Mb
3 Kathrein UFD 570/S Operation & user’s manual kathrein/ufd-570-s-665.pdf 07 Aug 2022 64
4 VTech vt2467 Operation & user’s manual vtech/vt2467-77R.pdf 18 Oct 2023 80 2.36 Mb
5 JVC LST0450-001B Instructions manual jvc/lst0450-001b-6O7.pdf 30 Apr 2023 60
6 Motorola SD7561 Operation & user’s manual motorola/sd7561-IYH.pdf 05 Feb 2024 60

Similar Resources:

  • CyberPower

    OR500LCDRM1U

    (1 pages)
    WARNINGBATTBATTERYUSING!ONPOWERLOADAVRWARNINGLOADBATTONPOWERAVRBATTERYUSING!WARNINGLOADBATTONPOWERAVRBATTERYUSING!WARNINGBATTUSING!LOADONPOWERAVRBATTERYBATTERYAVRPOWERONLOAD!USINGBATTWARNING1. Remove the right side front panel.2. Remove the three retaining screws for the cable protection cover and remove the cover. 3. Remove the two retaining screws from the …
  • Quantum

    DXi4800

    (2 pages)
    DXi4800 QUICK STARTUsing variable-length deduplication, the DXi4800 provides scalable, backup storage. The DXi4800 provides easy to configure disaster recovery protection when it is paired with one or more DXi system as a replication target. For complete documentation, including pre-installation requirements, see the DXi4800 Documentation Center: www.quantum …
  • Maruson

    Power Pro 550VA

    (2 pages)
    USER MANUAL Let’s Connect @marusontechnology Power Pro LCD UPS Series 550VA / 800VA / 1000VA / 1500VA / 2000VA IMPORTANT SAFETY INSTRUCTIONS CAREFULLY READ BEFORE FIRST USE. SAVE THESE INSTRUCTIONS. This manual contains important safety instructions that must be followed to avoid fire, property damage, personal injury, or death. The warnings, preca …
  • Tripp Lite

    S3M100KX

    (72 pages)
    1Owner’s ManualSmartOnline® S3MX 3-Phase UPS SystemsModels: S3M100KX, S3M120KX, S3M160KX, S3M200KXInput: 220/230/240V (Ph-N), 380/400/415V (Ph-Ph), 3Ø 4-Wire + PE1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/supportCopyright © 2018 Tripp Lite. All rights reserved. …
  • Ever

    SINLINE RT XL 1250

    (2 pages)
    >10cm>10cm+5 ÷ +35 °Cmax. 1,8mb. Rear panel:5 61 24 735 61 24 735. DESCRIPTION OF LCD DISPLAY ICONSv3 20150917Type 01SINLINE RT XL 650 SINLINE RT XL 1250SINLINE RT XL 1650SINLINE RT XL 2250SINLINE RT XL 3000SINLINE RT XL 8501. Output sockets PN-E-93201 (10 A)2. Output sockets IEC 320 C13 (10 A): white - controlled black - non-c …
  • Atlantis Land

    600VA/300W A03-PE601

    (44 pages)
    Where solutions begin Company certified ISO 9001:2000 OnePower UPS 600VA/300W A03-PE601 MANUAL A03-PE601 _MX01 …

Comments, Questions and Opinions: