Manualios.com

Quicklynks T55 Owner's Manual

Quicklynks T55 Manual Online:

3.35, 1024 votes
Quicklynks T55 User Manual
Quicklynks T55 User Guide
Quicklynks T55 Online Manual

Text of Quicklynks T55 User Guide:

  • Quicklynks T55, CHECK OWNER S MANUAL , OBD2 CODE SCANNER 1 Table of contents 1. Introduction --------------------------------------------------------------------------------------2 1.1 What Is OBD? ---------------------------------------------------------------------------------2 1.2 Safety Precautions and Warnings-----------------------------------------------------2 1.3 Vehicle Coverage----------------------------------------------------------------------------3 1.4 Data Link Connector (DLC) Location------------------------------------------------4 1.5 How To Use------------------------------------------------------------------------

  • Quicklynks T55, CHECK OWNER S MANUAL , OBD2 CODE SCANNER 2 1. Introduction 1.1 What Is OBD? Definition: Onboard Diagnostics II - A second-generation emissions diagnostic system required on all 1996 and newer vehicles (though some 1994 and 1995 model year vehicles were equipped with early versions of the system). This OBD2/EOBD/CAN Code scanner is designed to work on all OBD2 compliant vehicles (include all 1996 and newer cars, lig ht trucks and SUVs sold in the World). OBD2 was adopted as part of a government mandateto lower vehicle emissions. This sophisticated program in the vehicle's main computer system

  • Quicklynks T55, CHECK OWNER S MANUAL , OBD2 CODE SCANNER 3 Always perform automotive testing in a safe environment. Wear safety eye protection that meets ANSI standards. Keep clothing, hair, hands, tools, test equi pment, etc. away from all moving or hot engine parts. Operate the vehicle in a well ventilated work area: Exhaust gases are poisonous. Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests. Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running. Put th

  • Quicklynks T55, CHECK OWNER S MANUAL , OBD2 CODE SCANNER 4 1.4 Data Link Connector (DLC) Location The 16-pin DLC is usually located under the instrument panel (dash), within 12 inches(300 mm) of center of the panel, on the driver's side of most vehicles. It should be easily accessible and visible from a kneeling position outside the vehicle with the door open. For some Asian or European vehicles, the DLC is located behind the ashtray and the ashtray must be removed to access the connector. DLC 1.5 How To Use . . . . 1. Turn the ignition off. 2. Connect the OBD2 scanner to

  • Quicklynks T55, CHECK OWNER S MANUAL , OBD2 CODE SCANNER 5 2.Product Information 2.1 Tool Description 7 3 4 6 1 2 5 1. LCD DISPLAY --—Indicates test results. Backlit, 128 X 64 pixel display with contrast adjustment. 2. "Y" BUTTON -- Confirms a selection (or action) from a menu. When a DTCs definition covers more than one screen.it is used to move down to the next screen for additional data. 3. "N" BUTTON -- Cancels a selection (or action)from a menu or returns to the menu.It is also used to set up the unit when being pressed and held for at least 3 seconds.

  • Quicklynks T55, CHECK OWNER S MANUAL , OBD2 CODE SCANNER 6 4. UP SCROLL BUTTON -- Moves up through menu and submenu items in menu mode. When more than one DTC is retrieved, moves up throug h the current screen to the previous screens for additional DTCs and definitions. 5. DOWN SCROLL BUTTON -- Moves down throug h menu and submenu items in menu mode. When more than one DTC is retrieved, moves down throug h the current screen to the previous screens for additional DTCs and definitions. 6. POWER BUTTON -- Turns POWER ON or OFF. 7. OBDII CONNEC

  • CHECK OWNER S MANUAL , OBD2 CODE SCANNER 7 3). " "”-- A flashing UP Arrow indicates additional information is available on the previous screen. 4). " Pd " -- Identifying a Pending DTC when viewing DTCs. 2.5 Keyboard No solvents such as alcohol are allowed to clean the keypad or display. Use a mild nonabrasive detergent and a soft cotton cloth

  • Quicklynks T55, CHECK OWNER S MANUAL , OBD2 CODE SCANNER 8 2). From the Main Menu: Use the UP/DOWN scroll buttons to select System Setup and then press the Y button. Follow the instructions to make adjustments and settings as described in the following setup options. Main Menu ====================== 1) VW/AUDI 2) OBDII/EOBD 3) Oil Reset 4) System Setup Contrast Adjustment 1. From the system setup menu: Use the UP/DOWN scroll buttons to select Contrast and press the Y button. System Setup =================== 1) Contrast 2) Display Test 3) Keyboar

  • Quicklynks T55, CHECK OWNER S MANUAL , OBD2 CODE SCANNER 9 3). Press the Y button to save your selection and return to previous menu. 4). Press the N button to return to previous menu. Display Test The Display Test is used to check the LCD display. 1). From the System Setup menu, use the UP/DOWN scroll buttons to select Display Test and press the Y button. 2). Select Display Test from the Display test menu and press the Y Button. 3). Press the Y button again to start test. Look for missing spots in the solid black characters. Display Test ====================== Press [Y ] to test Look for missing spots in characters. Press [N] to return

  • Quicklynks T55, CHECK OWNER S MANUAL , OBD2 CODE SCANNER 10 System Setup ====================== 1) Contrast 2) Display Test 3) Keyboard Test 2). Press any key to start test. When you press a key, the key name should be observed on the display. If the name does not show up, then the key is not functioning properly. Keyboard Test ===================== Press any key to Start test to display name. Key:Double [N] to return 3). Double press N to return to the previous menu. 3.Operating Instr

  • Quicklynks T55, CHECK OWNER S MANUAL , OBD2 CODE SCANNER 11 7). Use the UP/DOWN scroll buttons to select the system from the Select System menu and press the Y button. If the scan tool fails to communicate with the selected Vehicle's ECU(Elec- tronic Control Unit). a " LINK ERROR "”message shows up on the display. √ Verify that the ignition is ON: √ Check if the scan tool's 0BDII connector is securely connected to the vehicle's DLC; √ Verify that the module supported; √

  • Quicklynks T55, CHECK OWNER S MANUAL , OBD2 CODE SCANNER 12 The numbers (01.02.15.03.08.etc) in front of the system names refer to the physical addresses assigned to the systems, not the sequence of the systems to be arranged. 8). Select Read Codes from the Select Function menu and press the Y button. If there are no Diagnostic Trouble Codes present, the display will indicate NO CODES ARE STORED IN THE MODULE! If there are any Diagnostic Trouble Codes present, the DTC number and its definition will show On the LCD display. The subcode, the communication protocol, the sequence of The DTC current- ly bei

  • CHECK OWNER S MANUAL , OBD2 CODE SCANNER 13 Erasing Codes CAUTION:Erasing the Diagnostic Trouble Codes may allow the scan tool to delete not only the codes from the vehicle's on—board computer, but also " Freeze Frame " data and manufacturer specific enhanced data. Further, the I/M Readiness Monitor Status for all vehicle monitors is reset to Fail s

  • Quicklynks T55, CHECK OWNER S MANUAL , OBD2 CODE SCANNER 14 6). If the codes are not cleared then an "ERASE FAILURE!" message will appear. Press the N button to return to previous menu. Viewing ECU Information 1). To view ECU Information.Use the UP/DOWN scroll buttons to select ECU Information from the Select Function menu and press the Y button. If the scan tool is not connected or no communication is established with the vehicle yet, then refer to Reading Codes from 1 to 7 at Paragraph 3.l. ECU Information ======================== VAG No.:06A906032TF Component: Bosch 1.815VT 0020 Coding: 0008570 Imp: 0000 WSC:000

  • CHECK OWNER S MANUAL , OBD2 CODE SCANNER 15 " Pass " --- Indicates that a particular monitor being checked has not compl- eted its diagnostic testing. " Fail " --- Indicates that a particular monitor being checked has not comple- ted its diagnostic testing or the monitor is not supported on that vehicle. 3). Use the UP/DOWN scr

  • Quicklynks T55, CHECK OWNER S MANUAL , OBD2 CODE SCANNER 16 3.2 OBDII/EOBD Diagnostics Reading Codes CAUTION: Don't connect or disconnect any test equi pment with ignition on or engine running. I). Turn the ignition off. 2). Locate the vehicle's 16 pin Data Link connector(DLC). 3). Plug into the scan tool cable connector to the vehicle DLC. 4). Turn the ignition on. But do not start the engine. 5). Press the Y button. The Main Menu will be observed on the Display. 6). Use the UP/DOWN scroll buttons to select OBDII/EOBD from the menu. Main Menu ====================== 1) VW/AUDI 2) OBDII/EOBD 3) Oil Reset 4) System Setup 7). Press the Y button.

  • Quicklynks T55, CHECK OWNER S MANUAL , OBD2 CODE SCANNER 17 If there are no Diagnostic Trouble Codes present, the display will indicate NO CODES ARE STORED IN THE MODULE! ” If there are any Diagnostic Trouble Codes present, the Fault Codes and Pending Codes will be reported on the display. OBDII/EOBD Diag. ======================== 1) Read Codes 2) Erase Codes 9). Use the UP/DOWN scroll buttons to select Read Codes from the menu and press the Y button. The DTC number will a

  • Quicklynks T55, CHECK OWNER S MANUAL , OBD2 CODE SCANNER 18 If the scan tool is not connected or no communication is established with the vehicle yet, then refer to Reading Codes from 1 to 8 at Paragraph 3.2. 2). A warning message comes up asking for your confirmation. Erase Codes ======================= Erase trouble codes! Are you sure? YES <NO > 3). If you do not want to proceed with erasing the codes, press the N button to exit. A message of "command cancelled" will show up. 4). If you do wish to proceed to erase the codes, then press the Y button. 5). If the codes are cleared successfully. an "ERASE DONE!" confirmation will show on the dis

  • CHECK OWNER S MANUAL , OBD2 CODE SCANNER 19 3.3 Oil Reset 1). Turn the ignition off. 2). Locate the vehicle's 16-pin Data Link Connector(DLC). 3). Plug into the scan tool cable connector to the vehicle's DLC. 4). Turn the ignition on. But do not start the engine. 5). Press the Y button. The Main Menu will be observed on the display. 6). Use the UP/DOWN scroll buttons to se

  • Quicklynks T55, CHECK OWNER S MANUAL , OBD2 CODE SCANNER 20 9). If the Service Reset Failed message appears then there might be problems for the scan tool to communicate with the vehicle being tested. Refer to the vehicle service manual for more information. 10). When done, turn off the ignition and disconnect the scan tool. 4. Warranty and Service 4.1 Limited One Year Warranty The Manufacturer warrants to the original purchaser that this product is free of defects in materials and workmanshi p for a period of one (1) year from the date of original purchase, subject to the following terms and conditions: 1). If the product fails

Related Products and Documents (Scanner):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 LG DP570MH Owner's manual lg/dp570mh-7X9.pdf 24 Mar 2023 42
2 D3D D10 Quick view d3d/d10-H2B.pdf 28 Aug 2022 4
3 ASROCK 970A-G3.1 Operation & user’s manual asrock/970a-g31-6PA.pdf 10 Jan 2023 71
4 GE Security S731DV Installation instructions manual ge-security/s731dv-7AB.pdf 04 Sep 2022 12
5 Panasonic KX-TGP600 Manual  panasonic/kx-tgp600-26Q.pdf 16 Oct 2023 2
6 Rail King 6-8-6 BANTAM TURBINE Steam Engine Operation manual rail-king/6-8-6-bantam-turbine-steam-engine-8F2.pdf 11 Aug 2022 27

Similar Resources:

  • Ricoh

    Aficio SP C240SF

    (456 pages)
    Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read "Safety Information" before using the machine.1Guide to the Machine2Getting Started3Using the Printer Function4Using the Copier Function5Using the Scanner Function6Using the Fax Function7Configuring the Machine Us …
  • Medit

    T710

    (2 pages)
    Medit T710 / T510 / T310 Scanner Repair PolicySeptember 15, 2020Warranty repair serviceMedit’s standard product warranty and extended product warranty service include the repair and replacement of defective products or product components by Medit or its authorized repair facilities. For warranty repair services, the customer must rst contact the Medit a …
  • Epson

    Perfection V37

    (2 pages)
    4134256 Rev.0 4134256 Rev.0 4134256 Rev.0 4134256 Rev.01-F C 1-F M 1-F Y 1-F KEpson Perfection® V37/V370 Photo Start Here • Point de départ Read these instructions before using your product. • Lisez ces instructions avant d’utiliser votre produit. Turn on scanner • Mettez le scanner sous tension3Note: To turn off the scanner, …
  • Epson

    E10000XL-GA

    (2 pages)
    EMP-TW10• A3+ professional graphic arts colour flatbed scanner• New MatrixCCD optimised for highest quality 2400dpi A3 scans• Optical auto-focus and manual focus system for sharp, precise images• Instant Xenon start lamp for an always ready solution• Features SilverFast® Ai 6 complete with IT8 calibration targetsDesigned to meet the most demanding …
  • Bridgeport

    SCX-5935

    (5 pages)
    Set up Scan to Email – SCX-5935 Get the IP address of the machine 1. Press Machine Setup 2. Touch Machine Status 3. Touch the Machine Info tab 4. Touch Print Report 5. Select Configuration Report 6. Touch Print 7. Touch Home The IP address of the machine is located on the configuration report. …
  • Visioneer

    9650

    (2 pages)
    The 42-bit color Visioneer 9650 USB scanner with Built-inAutomatic Document Feeder (ADF) delivers excellent performance, unbeaten quality,and unmatched ease of use making it the perfect office productivity tool.Featuring:• Automatic Document Feeder (ADF) and Flatbed Scanning• Scan up to legal size documents using the ADF• ADF Speed up to 12ppm at 200 d …

Comments, Questions and Opinions: