Manualios.com

SeaLevel ULTRA 530.LPCI Operation & User’s Manual

SeaLevel ULTRA 530.LPCI Manual Online:

3.25, 1778 votes
SeaLevel ULTRA 530.LPCI User Manual
SeaLevel ULTRA 530.LPCI User Guide
SeaLevel ULTRA 530.LPCI Online Manual

Text of SeaLevel ULTRA 530.LPCI User Guide:

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. SL9054 Revision 7/2006 ULTRA 530.LPCI User Manual Table of Contents INTRODUCTION....................................................................................................................................... 1 OTHER SEALEVEL LOW PROFILE PCI SERIAL I/O PRODUCTS...................................................... 1 BEFORE YOU GET STARTED ...............................................................................................................2 WHAT’S I

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. - 1 - ULTRA 530.LPCI User Manual Introduction The ULTRA 530.LPCI is a one channel PCI Bus serial I/O adapter. It provides one field selectable RS-232/422/485/530 serial port supporting asynchronous data rates up to 921.6K bps as well as isochronous data rates up to the speed of the supplied clock. Now, with this card, you can use your standard communications software and connect over a clocked digital communications line. Configure the port as RS-232 for standard serial COM: port requirements. Choose the RS-422 mode for long distance device connections up to 4000ft. where noise immunity and high data integrity are essential. Select RS-485 and ca

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. - 2 - ULTRA 530.LPCI User Manual Before You Get Started What’s Included The ULTRA 530.LPCI is shipped with the following items. If any of these items is missing or damaged please contact Sealevel for replacement.  ULTRA 530.LPCI Adapter  Sealevel SeaI/O Software CD Optional Items Depending upon your application, you are likely to find one or more of the following items useful for interfacing the ULTRA 530.LPCI to real-world signals. All items can be purchased from ou

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. - 3 - ULTRA 530.LPCI User Manual Card Setup RS-485 Enable Modes RS-485 is ideal for multi-drop or network environments. RS-485 requires a tri-state driver that will allow the electrical presence of the driver to be removed from the line. The driver is in a tri-state or high impedance condition when this occurs. Only one driver may be active at a time and the other driver(s) must be tri-stated. The output modem control signal Request To Send (RTS) is typically used to control the state of the driver. Some communication software packages refer to RS-485

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. - 4 - ULTRA 530.LPCI User Manual RS-485 Mode Examples (Header E5) Figure 1- Header E5, RS-422 Figure 2 – Header E5, RS-485 ‘Auto’ Enabled, with ‘No Echo’ Figure 3 - Header E5, RS-485 ‘Auto’ Enabled, with ‘Echo’ Figure 4 - Header E5, RS-485 ‘RTS’ Enabled, with ‘No Echo’ Figure 5 – Header E5, RS-485 ‘RTS’ Enabled, with ‘Echo’

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. - 5 - ULTRA 530.LPCI User Manual Figure 6 – Header E5, RS-485 ‘DTR’ Enabled, with No Echo Address and IRQ selection The ULTRA 530.LPCI is automatically assigned I/O addresses and IRQs by your motherboard BIOS. Only the I/O address may be modified by the user. Adding or removing other hardware may change the assignment of I/O addresses and IRQs. Line Termination Typically, each end of the RS-485 bus must have line-terminating resistors (RS-422 terminates at the receive end only). A 120-ohm resistor is across

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. - 6 - ULTRA 530.LPCI User Manual Electrical Interface Selection Each port on the ULTRA 530.LPCI has the ability to be used in either RS-232 or RS-422/485. This is selectable via two 24 pin DIP-shunts at E1and E2. Please use the following illustration to aid in the configuration of your electrical interface. Figure 8 - Headers E1 & E2, RS-232 Selected Figure 9 - Headers E1 & E2, RS-422/485 Selected

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. - 7 - ULTRA 530.LPCI User Manual Clock Modes The ULTRA 530.LPCI employs a unique clocking option that allows the end user to select from divide by 8 and divide by 1 clocking modes. These modes are selected at Header E6. To select the Baud rates commonly associated with COM: ports (i.e. 2400, 4800, 9600, 19.2, … 115.2K Bps ) place the jumper in the divide by 8 mode (silk-screen D8). Figure 10 - Clocking Mode ‘Divide By 8’ To select the maximum data rate (921.6K bps) place the jumper in the divide by 1 (silk-screen D1) position. Figure 11 - Clocking Mode ‘Divide By 1’

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. - 8 - ULTRA 530.LPCI User Manual Baud Rates and Divisors for the ‘Div1’ mode The following table shows some common data rates and the rates you should choose to match them if using the adapter in the ‘Div1’ mode. For this Data Rate Choose this Data Rate 1200 bps 150 bps 2400 bps 300 bps 4800 bps 600 bps 9600 bps 1200 bps 19.2K bps 2400 bps 57.6 K bps 7200 bps 115.2 K bps 14.4 K bps 230.4K bps 28.8 K bps 460.8K bps 57.6K bps 921.6K bps 115.2K bps If your communications package allows the use of Baud rate divisors, choose the appropriate divisor from the follow

  • © Sealevel Systems, Inc. - 9 - ULTRA 530.LPCI User Manual Software Installation Windows 98/ME/2000/XP Installation 1. Start Windows. 2. Insert the Sealevel Systems CD in to your CD drive. 3. If ‘Auto-Start’ is enabled for this drive the software will automatically launch. Otherwise, point your browser to the ‘Index.htm’ on the root directory of the

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. - 10 - ULTRA 530.LPCI User Manual Linux Installation Note: You MUST have "root" privileges to install the software and drivers. 1. Login as "root". 2. Mount the CDROM by typing: mount -t iso4860 /dev/hdc /cdrom Note: Your cdrom may not be /dev/hdc it could be /dev/hda, /dev/hdb, /dev/hdd, or if you have a SCSI drive /dev/sda, /dev/sdb, /dev/sdc, etc. You may mount the CDROM to any location, the /cdrom is just a common example. 3. Next change to the directory where you mounted the CDROM: Ex. cd

  • © Sealevel Systems, Inc. - 11 - ULTRA 530.LPCI User Manual Physical Installation The adapter can be installed in any 5V PCI expansion slot. Do not install the Adapter in the machine until the software has been fully installed. 1. Turn off PC power. Disconnect the power cord. 2. Remove the PC case cover. 3. Locate an available 5V PCI slot and r

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. - 12 - ULTRA 530.LPCI User Manual Technical Description The Sealevel Systems ULTRA 530.LPCI provides a PCI interface adapter with an additional asynchronous serial port providing a versatile interface, field selectable as RS-232 for modems, printers and plotters, as well as RS-422/485/530 for industrial automation and control applications. The ULTRA 530.LPCI utilizes the 16850 UART. This chip features programmable baud rates, data format, interrupt control and a 128-byte input and output FIFO. The ULTRA 530.LPC

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. - 13 - ULTRA 530.LPCI User Manual RS-422/485/530 Pin Assignments (DB25 Male) Signal Name Pin # Mode GND Ground 7 RDB RX+ Receive Positive 16 Input RDA RX- Receive Negative 3 Input CTSB CTS+ Clear To Send Positive 13 Input CTSA CTS- Clear To Send Negative 5 Input DSRB DSR+ Data Set Ready Positive 22 Input DSRA DSR- Data Set Ready Negative 6 Input DCDB DCD+ Data Carrier Detect Positive 10 Input DCDA DCD Data Carrier Detect Negative 8 Input TDB TX+ Transmit Positive 14 Output TDA TX- Transmit Negative 2 Output RTSB RTS+ Request To Send Pos

  • © Sealevel Systems, Inc. - 14 - ULTRA 530.LPCI User Manual Electrical Characteristics Features  Configurable for RS-232, RS-422, RS-485, or RS-530  16C850 buffered UART with 128-byte FIFOs  Data rates to 460.8K bps  MD1 Low Profile and Universal Bus (3.3V and 5V) compatible  Automatic RS-485 enable/disable Specifications Temperature Ran

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. - 15 - ULTRA 530.LPCI User Manual Appendix A - Troubleshooting Following these simple steps can eliminate most common problems. 1. Install software first. After installing the software then proceed to adding the hardware. This places the required installation files in the correct locations. 2. Read this manual thoroughly before attempting to install the adapter in your system. 3. Identify all I/O adapters currently installed in your system. This includes your on-board serial ports, controller cards, sound cards etc. The I/O address

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. - 16 - ULTRA 530.LPCI User Manual Appendix B - How To Get Assistance Begin by reading through the Trouble Shooting Guide in Appendix A. If assistance is still needed please see below. When calling for technical assistance, please have your user manual and current adapter settings. If possible, please have the adapter installed in a computer ready to run diagnostics. Sealevel Systems provides an FAQ section on its web site. Please refer to this to answer many common questions. This section can be found

  • © Sealevel Systems, Inc. - 17 - ULTRA 530.LPCI User Manual Appendix C – Electrical Interface RS-232 Quite possibly the most widely used communication standard is RS-232. This implementation has been defined and revised several times and is often referred to as RS-232 or EIA/TIA-232. The IBM PC computer defined the RS-232 port on a 9 pin D sub connector and subsequent

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. - 18 - ULTRA 530.LPCI User Manual Appendix D – Asynchronous Communications Serial data communications implies that individual bits of a character are transmitted consecutively to a receiver that assembles the bits back into a character. Data rate, error checking, handshaking, and character framing (start/stop bits) are pre-defined and must correspond at both the transmitting and receiving ends. Asynchronous communications is the standard means of serial data communication for PC compatibles and PS/2 computers. The original

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. - 20 - ULTRA 530.LPCI User Manual Appendix F - Compliance Notices Federal Communications Commission Statement FCC - This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may

  • SeaLevel ULTRA 530.LPCI, © Sealevel Systems, Inc. - 21 - ULTRA 530.LPCI User Manual Warranty Sealevel's commitment to providing the best I/O solutions is reflected in the Lifetime Warranty that is standard on all Sealevel manufactured products. We are able to offer this warranty due to our control of manufacturing quality and the historically high reliability of our products in the field. Sealevel products are designed and manufactured at its Liberty, South Carolina facility, allowing direct control over product development, production, burn-in and testing. Sealevel Systems, Inc. (hereafter "Seale

Related Products and Documents (PCI Card):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Ryobi WS730 Operator's manual ryobi/ws730-5RR.pdf 29 Mar 2023 56 2.87 Mb
2 Dura Heat GFA40 Operation & user’s manual dura-heat/gfa40-8P7.pdf 23 Mar 2024 18
3 Panasonic HDC-SD1 Operating instructions manual panasonic/hdc-sd1-I13.pdf 12 Sep 2023 124
4 SoundGate LEXPD2 Operation & user’s manual soundgate/lexpd2-3LM.pdf 06 Jan 2024 12
5 Rocktrail 79837 User manual manual rocktrail/79837-55C.pdf 27 Mar 2023 12
6 GEONAUTE HEART RATE MONITOR CWT500 Manual  geonaute/heart-rate-monitor-cwt500-934.pdf 14 Aug 2023 16 1.03 Mb

Similar Resources:

  • DAQ

    cPCI-FRM11

    (27 pages)
    cPCI-FRM11 User’s Manual (Rev 1.1) -1- http://www.daqsystem.com cPCI-FRM11 User’s Manual Windows, Windows2000, Windows NT and Windows XP are trademarks of Microsoft. We acknowledge that the trademarks or service names of all other organizations …
  • D-Link

    DI-604 - Express ENwork Router

    (1 pages)
    Cross Reference List - - Wireless & Ethernet ProductsCategory Product D-Link Linksys Netgear Belkin SMC US Robotics IntelHP/Compaq802.11bWireless Compact FlashDCF-660W WCF12 MA701 F5D6060 SMC2645W SWE1130Wireless USB AdapterDWL-120 WUSB11 MA101 F5D6050 SMC2664W USR1120 WUD2011B WL215Wireless PCI Adapter(Intergrated)DWL-520 WMP11 MA301 F5D6001 WPCI2011BW …
  • EzCAP

    284

    (49 pages)
    HD Video Capture Quick Start Guide Thanks for purchasing ezcap284 HD Video Capture. The following guides you how to set up. Hope this device will bring you nice digital experience. With this ezcap284 HD Video Capture, you can capture up to 1080P video from HDMI ,Ypbpr (component) or composite port, such as blue ray, set-top-box, computer, game box, VHS, …
  • SIIG

    LB-US0614-S1

    (2 pages)
    Features• Support data transfer rates up to 5Gb/s. Backward compatible with USB 2.0/1.1 devices• Provide reliable wired network connection in the speed of 10/100/1000Mbp• Support UASP (USB Attached SCSI Protocol)• Each port provides power output up to 900mAPackage contents• USB 3.0 3-Port Hub with LAN PCIe Host Card• Driver CD • Qui …
  • Koheron

    Alpha250

    (13 pages)
    ALPHA250 - User GuideGetting startedWarningsThe ALPHA250 power supply must be turned off before connecting or disconnecting: * the micro-SD card *peripherals on the expansion connectorTurn on the boardFirst, insert the micro-SD card into the micro-SD slot. Then connect the 12V jack of the power supply. The powergood green LED (PWGD) and the FPGA done orange …
  • Dalsa

    X64-AN Quad

    (129 pages)
    Artisan Technology Group is your source for quality new and certied-used/pre-owned equipment• FAST SHIPPING AND DELIVERY• TENS OF THOUSANDS OF IN-STOCK ITEMS• EQUIPMENT DEMOS• HUNDREDS OF MANUFACTURERS SUPPORTED• LEASING/MONTHLY RENTALS• ITAR CERTIFIED SECURE ASSET SOLUTIONSSERVICE CENTER REPAIRSExperienced engineers and techni …

Comments, Questions and Opinions: