PANASTEREO CX230EX Owner's Manual
|
PANASTEREO CX230 CINEMA MONITOR PANASTEREO CX230EX CINEMA BOOTH MONITOR OVERVIEW The CX230 Monitor is the world’s first computer controlled booth monitor. It is simple to use, provides advanced features not previously found in booth monitor equipment and has been designed for easy interface to computer automation systems via a standard RS232 interface connector. SYSTEM FEATURES • Sing
PANASTEREO CX230EX, PANASTEREO CX230 CINEMA MONITOR CX230 OPERATION MONITORING AN INDIVIDUAL CHANNEL Select a channel to be monitored by pressing the pushbutton for the appropriate channel once. An LED indicator will illuminate above the selected input button. Adjust the volume control for a comfortable listening level. The volume is indicated by the 2-digit display to the left of the control. Biamp installations only: It is possible to monitor each of the front channel high and low frequency outputs separately. Press the left, centre or right pushbutton o
PANASTEREO CX230EX, PANASTEREO CX230 CINEMA MONITOR CX230 INSTALLATION CONNECTING THE SOUND PROCESSOR OUTPUTS. NOTE: For non-biamped installations, the left channel should be connected to the LL input , the centre channel to the CL input and right channel to the RL input. 1. SOUND PROCESSOR WITH UNBALANCED OUTPUTS (DOLBY, SMART, ULTRA STEREO) Use two-core shielded audio cable to connect the outputs from the sound processor to the monitor “from processor” inputs. Connect the “+” terminal from each sound processor output to
PANASTEREO CX230 CINEMA MONITOR CX230 INSTALLATION con’t CONNECTING THE MONITOR SPEAKER OUTPUTS Use medium gauge (minimum 0.75mm2) twin polarised wire (figure 8) between each of the monitor speaker outputs and the monitor speakers. The monitor speakers can be 8 or 4 ohms. If you are using only one speaker, connect it to the left channel output and set the “MONO/STEREO” switch at the back of
PANASTEREO CX230EX, PANASTEREO CX230 CINEMA MONITOR SYSTEM ALIGNMENT After installation it is necessary to adjust each of the input levels of the monitor to ensure correct balance between each input and to calibrate the auditorium sound level meter. Alignment is best performed at the same time as the sound processor B-Chain alignment to avoid duplication. Equipment required: Pink Noise Card, Real Time Analyser (RTA) ALIGNMENT OF NON-BIAMPED SYSTEMS 1. Insert a pink noise card into the appropriate slot in the sound processor. 2. Set the sound process
PANASTEREO CX230EX, PANASTEREO CX230 CINEMA MONITOR 17. Select the pink noise generator to LEFT . 18. Check the SPL reading on the RTA. It should be 85dB. If not, check the B-Chain alignment of the sound processor. 19. Select the “SOURCE” switch to “AMPS”, and select “LEFT”. 20. Adjust the “AMPLIFIERS - LL” trimpot so that the CX230 sound level meter reads 85db. 21. Select the “SOURCE” switch to “PROC”. 22. Adjust the “Processor - LL” trimpot on the monitor so that the CX230 sound level meter reads 85db. 23. Select the pink noise generator to RIGHT . 24. Check the SPL reading on the RTA. It should be 85dB. If not, check the B-Chain alignment of the sound processor
PANASTEREO CX230EX, PANASTEREO CX230 CINEMA MONITOR 35. Select the pink noise generator to RIGHT SURROUND . 36. Check the SPL reading on the RTA. It should be 85dB. If not, check the B-Chain alignment of the sound processor. 37. Select the “SOURCE” switch to “AMPS”, and select “RIGHT SURROUND”. 38. Adjust the “AMPLIFIERS - RS” trimpot so that the CX230 sound level meter reads 85db. 39. Select the “SOURCE” switch to “PROC”. 40. Adjust the “Processor - RS” trimpot so that the CX230 sound level meter reads 85db. The CX230 a
PANASTEREO CX230EX, PANASTEREO CX230 CINEMA MONITOR ALIGNMENT OF BIAMPED SYSTEMS 1. Insert a pink noise card into the appropriate slot in the sound processor. 2. Set the sound processor volume to level “7” for a pink noise level of 85db in the auditorium. 3. Select the pink noise generator to CENTE R. 4. Turn off the Sub Bass amplifier. 5. Check the SPL reading on the RTA. It should be 85dB. If not, check the B-Chain alignment of the sound processor. 6. Turn off the Centre channel low frequency amplifier and note the SPL reading on the RTA. 7. Select the “SOURCE” switch to “AMPS”,
PANASTEREO CX230EX, PANASTEREO CX230 CINEMA MONITOR 17. Turn off both the Centre HF and LF amplifiers and turn on the Sub Bass amplifier. 18. Note the SPL reading on the RTA. 19. Select the “SOURCE” switch to “AMPS”, and select “SUB BASS”. 20. Adjust the “AMPLIFIERS - SW” trimpot so that the CX230 sound level meter reads the same as the SPL reading on the RTA. 21. Select the “SOURCE” switch to “PROC”. 22. Adjust the “Processor - SW” trimpot so that the CX230 sound level meter reads the same as the SPL reading on the RTA. 23. Turn on the Center HF and LF amplifiers. 24. Select the pink noise card to LEFT . 25. Check the SPL reading on the RTA. It
PANASTEREO CX230EX, PANASTEREO CX230 CINEMA MONITOR 37. Select the pink noise card to RIGHT . 38. Check the SPL reading on the RTA. It should be 85dB. If not, check the B-Chain alignment of the sound processor. 39. Turn off the Right channel low frequency amplifier and note the SPL reading on the RTA. 40. Select the “SOURCE” switch to “AMPS”, and select “RIGHT HF” by pressing the “RIGHT” pushbutton twice. Only the “HF” LED above the RIGHT pushbutton should be illuminated. 41. Adjust the “AMPLIFIERS - RH” trimpot so that the CX230 sound level meter reads the same as the SPL reading on the RTA. 42. Select the “SOURCE” switch to �
PANASTEREO CX230 CINEMA MONITOR 47. Select the pink noise generator to RIGHT SURROUND . 48. Check the SPL reading on the RTA. It should be 85dB. If not, check the B-Chain alignment of the sound processor. 49. Select the “SOURCE” switch to “AMPS”, and select “RIGHT SURROUND”. 50. Adjust the “AMPLIFIERS - RS” trimpot so that the CX230 sound level meter reads 85db. 51. Select the
PANASTEREO CX230EX, PANASTEREO CX230 CINEMA MONITOR REFERENCE DATA Serial Interface Protocol Description The CX230 is equipped with a standard RS232 serial communications port using a 9 pin D-sub connector. The data format is fixed and is in the following format: One start bit, eight data bits, one stop bit, no parity, 9600 baud. Command String Format “Input select” and “volume set” commands are constructed using a seven character ASCII string. Commands start with a colon followed by a four character command terminated with a carriage return , and a line feed character which are also valid if they occur in reverse order. (This is to allow compatibility with
PANASTEREO CX230EX, PANASTEREO CX230 CINEMA MONITOR MMIX Select Mix MAMP Select Amplifier Inputs MPRO Select Processor Inputs MMUT Select Mute Set Volume Commands: MVxx Set volume to xx, where xx is a number from “00” to “99”.
RocketFish RF-RBWS02 Home Theater System Operation & user’s manual
RF-RBWS02 |
Sony BRAVIA KDL-40S3000 Home Theater System Specifications
BRAVIA KDL-40S3000 |
Pace DC700X Home Theater System Operator's manual
DC700X |
Anthem AVM 20 Home Theater System Operation
AVM 20 |
Panasonic SCS3050 - HES SYSTEM Home Theater System Operating manual
SCS3050 - HES SYSTEM |
Sony KDS-70Q006 Home Theater System Quick setup manual
KDS-70Q006 |
Sony HT-BE1 Home Theater System Operating instructions manual
HT-BE1 |
Yamaha YHT-800 Home Theater System Quick connect manual
YHT-800 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Mellanox Technologies | InfiniBand X | Operation & user’s manual | mellanox-technologies/infiniband-x-LD9.pdf | 27 Jan 2023 | 96 | |
2 | NEC | Express5800 120Li | Getting started manual | nec/express5800-120li-OSQ.pdf | 24 Feb 2023 | 2 | |
3 | XM Satellite Radio | XDNX1V1KC | Operation & user’s manual | xm-satellite-radio/xdnx1v1kc-I62.pdf | 09 Aug 2022 | 58 | 4.78 Mb |
4 | Hasselblad | Prism Viewfinder PM45 | Operation & user’s manual | hasselblad/prism-viewfinder-pm45-4CR.pdf | 16 Jan 2024 | 2 | 0.72 Mb |
5 | Insinger | Rack-A-Matic | Specifications | insinger/rack-a-matic-9SJ.pdf | 26 Dec 2023 | 1 | |
6 | Panasonic | HHR160A | Specifications | panasonic/hhr160a-I9L.pdf | 27 Dec 2023 | 5 | 0.08 Mb |
JVC
JVCHOME THEATER RECEIVERRX-ES1SLo O0000000000000O0CD CZD CDCD CD CD CDH_@ © © ©Drl_ D,o,,*LAVI_I-tlIIDIIII&IV DIGITAL_w _wlr _ _w_ r_r_;lllr;T_T_lF1 SURROUNDINSTRUCTIONSFor Customer Use:Enter below the Model No. and Serial No.which are located either on the rear, bot-tom or side of the cabinet. Retain thisinformation for future reference.Model No.Seri …
RX-ES1SL(43 pages) |
Onkyo
EnFrEsEnFrEsAV RECEIVER / AMPLI-TUNER AUDIO-VIDEO TX-SR353Quick Start GuideGuide rapideGuía de iniciorápidoFor detailed descriptions of this unit, see the “Operating Instructions”. (En)http://www.onkyo.com/manual/txsr353/en.pdf Pour avoir une description détaillée de cet appareil, lire le “Mode d'emploi”. (Fr)http://www.onkyo.com/manual/txsr …
TX-SR353(24 pages) |
Panasonic
RDVD Home Theater Sound SystemOperating InstructionsModel No. SC-HT500PHONESDOWN UPVOLUMEOPEN/CLOSEDVD HOME THEATER SOUND SYSTEM SA-HT500Í/IRDS SFC SELECTORSUBWOOFERAC INAV SYSTEMSLEEPFL DISPLAYDIMMERPLAY MODEMIX 2CHREPEATP.MEMORY CANCELSKIPCHTOP MENUDISPLAYVOLUMEMUTINGSSS PL C.FOCUSCSM SFCSUBWOOFERLEVELFM MODESETUPZOOM GROUP AUDIORETURNTV VOL sTV VOL rDI …
SC-HT500(20 pages) |
Denon
AVR-788AV Surround ReceiverNew model informationA/V Surround Receiver featuring HD Video connectivity,that enhances your level of entertainment enjoyment.The Latest HD Video Support• HDMI1.3a inputs/output• HDMI audio support, Dolby Digital, dts and multi channel PCM• Deep Color up to 36-bit and xvYCC broader color space support• Discrete devices for …
AVR 788 - AV Receiver(2 pages) |
JBL
jbl reference series 610User GuideEnglish .........................2Deutsch ........................9Français .......................15Español ...................... 21Italiano .......................27Dutch ......................... 33Korean ........................39Norwegian ................. 45Danish .........................51Japanese ................ …
CINEMA 610(68 pages) |
Onkyo
En5.1ch Home Theater SystemHT-S4100AV Receiver (TX-SR304)Front Speakers (SKF-360F L/R)Center Speaker (SKC-360C)Surround Speakers (SKM-360S L/R)Subwoofer (SKW-460)Remote Interactive Dock (DS-A1XP)Instruction ManualThank you for purchasing an Onkyo 5.1ch Home Theater System. Please read this manual thoroughly before making connections and plugging in the unit …
HT-S4100(64 pages) |
McIntosh Amplifier MX 110Amplifier #N5S7H8 MX 110, 24 |
Olympia Telephone CDP24106Olympia Product Manual: CDP24106 PDF Operation & user’s manual - 6U641I CDP24106, 58 |
Datsun Automobile 510 seriesDatsun 510 series Automobile Workshop manual 510 series, 144 |
Belkin Extender EXPANDVIEW CAT5EXPANDVIEW CAT5 Operation & user’s manual - R58V4F EXPANDVIEW CAT5, 20 |
Barco Monitor ADP361Specifications for Barco ADP361 Monitor ADP361, 4 |
Zanussi Refrigerator ZL714WZL714W (Refrigerator ePDF Manual, #IEH1YT) ZL714W, 20 |
Philips Hair Dryer HP4879Operation & user’s manual for Philips HP4879 Hair Dryer HP4879, 100 |
Grandstream Networks IP Phone GXP1450Grandstream Networks GXP1450 User Guide (Operation & user’s manual), @6U6RZ7 GXP1450, 80 |
Russell Corporation Fitness Equipment M415221Russell Corporation Product User Manual: M415221 PDF Owner's manual - 3471Z9 M415221, 2 |
Yamaha Synthesizer YMM2User Guide: Yamaha YMM2 (YAL749, Upd.Tue 01.2024) YMM2, 6 |
Keysight Measuring Instruments N9000AKeysight Product User Manual: N9000A PDF Manual - 624P9D N9000A, 52 |
Macintosh Stereo Receiver MAC 1900Macintosh Product User Manual: MAC 1900 PDF Owner's manual - WGDC33 MAC 1900, 24 |