Manualios.com

Cypress Chameleon CTM-15X Complete Manual

Cypress Chameleon CTM-15X Manual Online:

3.8, 1497 votes
Cypress Chameleon CTM-15X User Manual
Cypress Chameleon CTM-15X User Guide
Cypress Chameleon CTM-15X Online Manual

Text of Cypress Chameleon CTM-15X User Guide:

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 54 6BCommand Reference ioemail n <email address> Sets the email address that the IO report will be sent to (if configured for email using iorep). Up to 8 email addresses may be configured – one for each of the 8 IO reports. The default email address is blank. n = 1 to 8 IO report number <email address> = name@domain email address to which the report will be sent (leave blank to clear the email address) The current email address can be queried for all IO reports by using the ioemail command without parameters. Note that an email server is required – see emails

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 98 6BCommand Reference cmd reptype 2 3 7 1 OK 3. Query the reporting methods for all reports cmd reptype cmd reptype 1 3 0 0 cmd reptype 2 3 0 0 cmd reptype 10 0 6 0 OK A cmd save is required for this command to take effect. See Also: repaddmes, repdelmes, repemail, replocport, repremip, repremport, repsms return to list of commands restore Restores the configuration to the previously saved version (overwrite any commands not yet saved). This command has the same effect as a power cycle

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 95 6BCommand Reference Examples: 1. Report #1 will be sent to remote IP address 123.10.1.101 cmd repremip 1 123.10.1.101 OK 2. Query the remote IP address setting of all reports cmd repremip cmd repremip 1 123.10.1.101 cmd repremip 2 199.99.99.99 OK A cmd save is required for this command to take effect. See Also: repaddmes, repdelmes, repemail, replocport, repremport, repsms, reptype return to list of commands repremport n xxxxx Sets the IP port number of the remote server that the report will be sent to. n = 1 to 999 report number xxxxx = 0 to

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 32 6BCommand Reference Examples: 1. Use report #2 for boom-tracker triggered reports. cmd boomreport 2 OK A cmd save is required for this command to take effect. See Also: mode, repaddmes, repdelmes, repemail, replocport, repremip, repremport, repsms, reptype return to list of commands 7.1.3 “C” Commands confupgrade script-name url username passwd Configures the modem for over-the-air configuration by means of a custom configuration script retrieved from a defined ftp serve

  • © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 126 7BReport Messages 4 bytes Time (based on number of seconds since 00:00:00 January 1st 1970 1 byte GPS data validity: 0x”A” = valid; 0x”V” = invalid; 0x”B” = buffered valid; 0x”W” = buffered invalid. 1 byte GPS quality: 0 = not valid; 1 = valid 1 to 1

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 107 6BCommand Reference snfflush Flushes and resets store and forward NVRAM. return to list of commands snflog n Used to display the contents of the store and forward log locally thru a serial console, and the status of the log entries. The log can contain up to 3000 records. This is a read only command. n = 1 to 3000 number of store reports to be displayed The number of stored reports and their status can be queried by entering snflog without parameters. T:t where t is the total number of stored reports F:f where f is the number of reports forwa

  • © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 135 8BEmail Message Format 8.29 Message Type 137, $PODO Proprietary NMEA message containing information about the odometer, or the total distance travelled, obtained via GPS position data. This returns the same value as cmd odometer. Message format is: $PO

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 4 0BActivating Your Modem Notice .......................................................................................................................................................... 2 Safety & hazards ......................................................................................................................................... 2 Regulatory restrictions .................................................................................................................

  • © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 61 6BCommand Reference cmd lanrepip cmd lanrepip 192.168.1.20 OK A cmd save is required for this command to take effect. See also: landhcp, landns, lanip, lannetmask return to list of commands 7.1.10 “M” Commands mip n Sets the Mobile IP ope

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 8 0BActivating Your Modem 12.6 Sealing ....................................................................................................................................... 146 12.7 Material..................................................................................................................................... 146 12.8 Power Supply ............................................................................................................................ 146 12.9 Host Connectiv

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 19 2BOperating Your Modem shutdown: Press and hold for 2 to 5 seconds (the PWR LED will go off at the 2-second mark). Press again for more than 0.25 second to return to operating mode. 3.4 LED Indicators There are five LED indicators on the CTM-15x top. These are used to show the status and operation of the device. For Sierra Wireless/Kyocera Wireless CDMA/EV-DO data devices or modules: LED Description Solid Blinking Off PWR Power status of the device full operating mode and

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 74 6BCommand Reference • Authentication key has been exchanged • Shared secrets data has been updated • New NAM parameters have been downloaded • New MDM has been downloaded • IMSI has been downloaded • PRL has been downloaded During updating, if any of the above data is unsuccessful, an OTASP Timeout message will be displayed. A progress message OTASP Processing will be displaye

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 124 7BReport Messages 8.8 Message Type 82, GPRMC Standard NMEA message containing time, GPS latitude and longitude, speed, altitude and heading information. Message format is: $GPRMC,hhmmss.ss,v,llll.llll,a,yyyyy.yyyy,b,ccc.c,ddd.d,ddmmyy,,*hh<CR><LF> Where: hhmmss.ss is the UTC time in hours, minutes, seconds, and decimal seconds v is the data validity flag: A = valid current data, B = valid stored data, V = invalid c

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 60 6BCommand Reference lannetmask iii.iii.iii.iii Sets the netmask of the modem on the LAN. iii.iii.iii.iii = 0.0.0.0 to 255.255.255.255 LAN netmask of the modem in decimal (default: 255.255.255.0) Note: Special care must be taken when configuring this command, if an improperly configured lannetmask IP address is entered the ethernet port can be rendered unusable. Before configuring this command it is advisable to make sure that a command console is available via the serial port, or the IP address is known and remote telnet is enabled to allow the modem to be accessed wirelessly.

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 134 7BReport Messages 8.27 Message Type 122, $POBDD Proprietary NMEA message containing OBD II information captured from a vehicle. There are 4 available messages for reporting OBD II/J1939 data, each message can return information on up to 4 parameters based on this table OBDII/J1939 parameters. Message format is: $POBDD,v,px=xxxxxx,[px=xxxxxx],[px=xxxxxx],[px=xxxxxx],ggggggggggg*hh<CR>&l

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 125 7BReport Messages 8.10 Message Type 85, ULCP binary position message with GPS coordinates Header: 0x55 0xSS 0x06 0x00 0x00 0x18 0x0000 Message body: Hex Description 4 bytes Normalized latitude (RMC latitude x 100,000) 4 bytes Normalized longitude (RMC longitude x 100,000) 2 bytes Speed in knots 2 bytes Heading 1 byte GPS data validity: 0x”A” = valid; 0x”

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 46 6BCommand Reference A cmd save is required for this command to take effect. See also: gpsrep, gpsdelmes, gpslocport, gpsaddmes, gpsremport, gpsemail, gpssms return to list of commands gpsremport n xxxxx Sets the IP port number of the remote server that the GPS report will be sent to. Up to 8 GPS reports can be configured. n = 1 to 8 or 11 GPS report number xxxxx = 0 to 65535 remote port

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 9 0BActivating Your Modem 1 Activating Your Modem 1.1 Gather Account Information 1.1.1 CDMA/EV-DO devices For Sierra Wireless AC595/AC597/AC598/AC580 CDMA/EV-DO devices, the following information is typically required: • Phone number (10-digit MDN) • Lock code (6-digit CSL) • User name (number@… format) • Password • Dial number (usually #777) For all other manufacturer data devices and cards, network activation of the device must be done in a laptop prior to installing in the modem. 1.1.2 GS

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 121 7BReport Messages Message format is: $PMID,xxxxxxxxxxx,yyyyyyyyyyy*hh<CR><LF> Where: xxxxxxxxxxx is the modem’s unique 11 digit ESN yyyyyyyyyyy is the modem’s ID as set by the user (maximum 11 characters) hh is the message checksum Example: $PMID,09604890968,09604890968*10 8.2 Message Type 16, $GPGLL This is a standard NMEA message containing GPS latitude and longitude information and time. Message format is: $GPGLL,llll.llll,a,yyyyy.yyyy,b,hhmmss.ss,v*hh<CR><LF> Where: llll.l

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 84 6BCommand Reference Maximum of 4 parameters can be configured for each report message. x = a, b, c, d n1 (n2, n3, n4 are optional parameters) = engine parameters as per table Examples: cmd pobda p1 reports vehicle speed cmd pobdb p2 p12 p25 reports engine speed, intake air temperature and total engine hours cmd pobdc pa pb reports calculated peak acceleration and calculated peak deacceleration cmd pobdd p20 rep

  • Cypress Chameleon CTM-15X, © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 67 6BCommand Reference n = 4 auto connect to both the network and the PAD host interface n = 5 auto connect to the network and serial LCD (future) n = 6 auto connect to both the network and the MODBUS host interface n = 8 auto connect to both the network and the Elmscan diagnostic tool for OBD II n = 9 auto connect to both the network and the magnetic swipe card reader n = 10 auto connect to both the network and the WPAN Gateway n = 12 auto connect to both the network and the Chlorobyte Salt Spreader interf

  • © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 111 6BCommand Reference telnettimeout n Sets the timeout period for a telnet session with no activity. The telnet timeout will take effect on the next telnet login. n = 0 to 65535 timeout time, in seconds (default: 60 seconds) The current telnet timeout setting can be

  • © 2009 Cypress Solutions Complete Manual: CTM-15X Firmware 1.2.0 (Revision 1.0) 13 1BInstalling Your Modem The modem can be installed in any orientation, but it is suggested that the modem not be mounted with the interconnect face directed upwards as this can allow liquids to enter the modem. The modem should be mounted in an area where it is free from excessive d

Related Products and Documents (Modem):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Zenith 19LS4D Installation and operating manual zenith/19ls4d-7B6.pdf 10 Jan 2024 70
2 Mi-T-M Chore Master Operation manual mi-t-m/chore-master-Q7N.pdf 14 Jun 2023 56
3 Yazoo/Kees Z9 Commercial Collection System Z9A Operator's manual yazoo-kees/z9-commercial-collection-system-z9a-984.pdf 26 Dec 2023 22 1.08 Mb
4 VST easyDAB+5 Operation & user’s manual vst/easydab5-AQR.pdf 16 Mar 2024 40
5 Telex EKP-632 Installation manual telex/ekp-632-JWP.pdf 22 Nov 2022 1 0.17 Mb
6 LG 55EG9600-UA Service manual lg/55eg9600-ua-85M.pdf 05 Aug 2022 54

Similar Resources:

  • Cisco

    EPC3208G EuroDOCSIS 3.0 8x4

    (8 pages)
    Data Sheet © 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information. Page 1 of 8 Data Sheet Cisco Model EPC3208G EuroDOCSIS 3.0 8x4 Cable Modem with Embedded Digital Voice Adapter The Cisco® Model EPC3208G EuroDOCSIS™ 3.0 8x4 Cable Modem (EPC 3208G) is a high-speed cable modem with an embedded digital voice ad …
  • Inter-m

    AOE-212N

    (32 pages)
    Operation ManualAudio Over EthernetAOE-212N* Rack mount products in the Western Hemisphere(North America, South America,and the Caribbean) do not have handles installed due to customer preference. …
  • Four-Faith

    F-B200GLGL

    (34 pages)
    F-B200GLGL NB-IoTmodule hardware designmanualDocument VersionSecurityV1.0.3F-B200GLGL35 pagesF-B200GL NB-IoT ModuleHardware Design ManualXiamen Four-Faith Communication Technology Co., Ltd.Add: Floor 11, Area A06, No 370,chengyistreet,Jimei,XiamenTel: +86 592-5907276 Fax: +86 592-5912735Web: http://en.four-faith.com …
  • SMC Networks

    SMC8004CM

    (2 pages)
    n Connect the Cables and Power AdapterTo use the computer’s USB interface to connect to the Internet, use the provided USB cable toconnect the computer and the cable modem.A. Power off the computer and television.B. Unplug the computer and television.C. Connect the RF coaxial cable (not included) to the cable modem’s CATV cable connec-tor and to the wall …
  • TC Communications

    TC2100

    (26 pages)
    Notice!Although every effort has been made to insure that this manual iscurrent and accurate as of date of publication, no guarantee is givenor implied that it is error free or accurate with regard to anyspecification. TC Communications, Inc. reserves the right tochange or modify the contents of this manual at any time withoutprior notif …
  • Digi

    XBee

    (71 pages)
    Digi International Inc.11001 Bren Road EastMinnetonka, MN 55343 877 912-3444 or 952 912-3444 http://www.digi.com XBee®/XBee-PRO® RF ModulesXBee®/XBee-PRO® RF ModulesRF Module OperationRF Module ConfigurationAppendicesProduct Manual v1.xEx - 802.15.4 ProtocolFor RF Module Part Numbers: XB24-A...-001, XBP24-A...-001IEEE® 802.15.4 RF Modules by Digi Intern …

Comments, Questions and Opinions: