Manualios.com

Sharp MX-FNX9 Service Manual

Sharp MX-FNX9 Manual Online:

3.5, 1095 votes
Sharp MX-FNX9 User Manual
Sharp MX-FNX9 User Guide
Sharp MX-FNX9 Online Manual

Text of Sharp MX-FNX9 User Guide:

  • MX-FNX9 OPERATIONAL DESCRIPTIONS 5 – 7 2) For the second and later sheets of a bundle, the inlet port sen- sor (FED) turns ON and a certain amount is transported, and then the alignment motor F (FFJM) and the alignment motor R (FRJM) are driven to shift the alignment plate to 15mm outside the paper and to put it under the standby state. 3) After the paper rear edge passes the p

  • Sharp MX-FNX9, MX-FNX9 DISASSEMBLY AND ASSEMBLY 6 – 13 (8) Punch position sensor 1) Remove the punch unit. Refer to A-(1). 2) Remove the upper unit. Refer to A-(5). 3) Remove the harness guide. 4) Remove the punch position sensor. (9) Horizontal shift HP sensor 1) Remove the punch unit. Refer to A-(1). 2) Remove the guide cover and the harness guide. Refer to A- (3). 3) Disconnect the connector, and remove the harness. 4) Remove the screws and the pawl, and lift up the harness guide. Disconnect the connector, and remove the horizontal shift HP sensor. (1

  • Sharp MX-FNX9, MX-FNX9 DISASSEMBLY AND ASSEMBLY 6 – 1 MX-FNX9 Service Manual [6] DISASSEMBLY AND ASSEMBLY 1. MX-FNX9 A. Exterior (1) Inner finisher 1) Loosen the screw, and disconnect the connector from the main unit. 2) Open the front cover, and remove the punch unit cover. 3) Remove the stopper. 4) Remove the screw, and remove the rail stay. 5) Remove the inner finisher from the main unit. (2) Inner cover 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the inner cover. (3) Rear cover 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Slide the rail, and remove the rear cover. (4) Left c

  • Sharp MX-FNX9, MX-FNX9 OPERATIONAL DESCRIPTIONS 5 – 8 B. Paper take-up, alignment and staple 1) For the first sheet of a bundle, after turning on the inlet sensor (FED), the roller up/down motor (FSWM) is driven to lower the bundle exit roller. The bundle exit motor (FAM) is driven at the paper exit speed of the main unit to drive the bundle exit roller. By turning on the inlet port sensor (FED), the alignment motor F (FFJM) and the alignment motor R (FRJM) are driven to shift the alignment plate to 15mm outside the paper and to put it under the standby state. After transport of a certain amount, the roller up/down motor

  • Sharp MX-FNX9, MX-FNX9 DISASSEMBLY AND ASSEMBLY 6 – 4 (9) Take-up belt, paper exit roller 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the inner cover. Refer to A-(2). 3) Remove the reverse guide unit. Refer to A-(5). 4) Remove the parts, and remove the bundle roller up/down lever unit. 5) Remove the parts, and remove the bundle roller unit. 6) Remove the parts, and pull out the belt unit. Remove the parts, and remove the belt unit. 7) Remove the parts, and remove the take-up belt and the paper exit roller. (10) Inlet port gate 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the inner cover. Refer to A-(2). 3

  • Sharp MX-FNX9, MX-FNX9 DISASSEMBLY AND ASSEMBLY 6 – 9 6) Remove the bracket, and remove the paper surface sensors 1, 2. (2) Paper surface detection solenoid 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the inner cover. Refer to A-(2). 3) Remove the tray unit. Refer to B-(10). 4) Remove the bundle exit paper transport roller unit, the sensor lever, the process tray unit. Refer to C-(1). 5) Remove the paper surface detection solenoid unit, and remove the paper surface detection solenoid. (3) Tray upper limit sensor, tray intermediate lower limit sensor, tray lower limit sensor 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Rem

  • Sharp MX-FNX9, MX-FNX9 SELF DIAGNOSTICS AND TROUBLE CODES 9 – 2 Phenomenon A document is discharged to the reverse path in the operation other than reverse operation. Case 1 Cause Flapper solenoid (FINRPS) connector pin trouble Check & Remedy Check the connection state of the connector. (CN15) Case 2 Cause Solenoid coil disconnection Check & Remedy Perform the conduction test of the coil. If there is no conduction, replace the coil. Case 3 Cause Control PWB trouble Check & Remedy If the flapper solenoid (FINRPS) does not operate in the solenoid single operation mode, replace the control PWB. Phenomenon T

  • MX-FNX9 OPERATIONAL DESCRIPTIONS 5 – 5 2. General This chapter describes operations of the inner finisher. The major operation modes are as follows: • Non-sort mode • Offset mode • Staple mode • Non-sort mode + punch • Offset mode + punch • Staple mode + punch In this chapter, the basic operations of the non-sort mode, the offset mode, and the staple mode are d

  • Sharp MX-FNX9, MX-FNX9 DISASSEMBLY AND ASSEMBLY 6 – 3 (4) Roller up/down sensor 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the inner cover. Refer to A-(2). 3) Remove the bracket, and remove the roller up/down sensor. (5) Take-up belt sensor 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the inner cover. Refer to A-(2). 3) Slide the harness guide, remove the bracket, and remove the take-up belt sensor. (6) Roller up/down motor 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the inner cover. Refer to A-(2). 3) Remove the rear cover. Refer to A-(3). 4) Remove the reverse guide un

  • MX-FNX9 EXTERNAL VIEW AND INTERNAL STRUCTURE 4 – 3 (2) MX-PNX1A/B/C/D No. Signal Name Type Function/Operation Output 1 FPDD Full sensor Photo interrupter Detects full of the punch dust container. When full, TP2 on the punch PWB remains “H” level. 2 FPHPD Punch position sensor Photo interrupter Detects the home position of the punch up/down shift. TP47 on the control PWB of t

  • Sharp MX-FNX9, SERVICE MANUAL Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. This document has been published to be used for after sales service only. The contents are subject to change without notice. SHARP CORPORATION [1] PRODUCT OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 [2] SPECIFICTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . .

  • Sharp MX-FNX9, MX-FNX9 ELECTRICAL SECTION 10 – 4 2) Bundle exit motor (FAM) drive circuit This circuit controls rotation/stop rotating direction and current of the bundle exit motor (FAM), and is composed of the CPU (IC10), the DA converter (IC11), and the constant-current chopper system driver IC (IC8). The motor rotating speed and the rotting direction are controlled with the stepping motor drive excitement pattern signal (T_MOT_A, *A, B, *B) outputted from the CPU (IC10-79, 80, 81, 82pin). The analog signal (T_MOT_REF) outputted from the DA converter (IC11-5pin) is divided into a certain voltage with R74 and R75.

  • Sharp MX-FNX9, MX-FNX9 SPECIFICTIONS 2 – 2 *4: Thick paper (In the cover paper mode, allowable only 2 (in total of the front cover paper and the back cover paper) + plain paper.)) *5: Follows the paper type registration setting. B. Allowable load quantity for each size *1: 250 sheets or height of 35.5mm or less *2: 500 sheets or height of 71mm or less *3: Up to 10 envelopes can be loaded on the load tray. *4: 250 sheets or 30 sets, or height of 35.5mm or less *5: 500 sheets or 30 sets or height of 71mm or less *6: Similarly with plain paper, the load capacity of thin paper, heavy paper, and glossy paper is limited to the earliest reach of the above number of

  • Sharp MX-FNX9, MX-FNX9 DISASSEMBLY AND ASSEMBLY 6 – 12 3) Remove the punch horizontal resist motor. (4) Punch PWB 1) Remove the punch unit. Refer to A-(1). 2) Remove the guide cover and the harness guide. Refer to A- (3). 3) Remove the punch PWB. (5) Punch motor 1) Remove the punch unit. Refer to A-(1). 2) Disconnect the connector, and remove the link plate. Remove the spring, and separate the upper unit and the lower unit. 3) Fit the gear hole with the screw position, and remove the screw. Remove the punch motor. (6) LED light emitting PWB 1) Remove the punch unit. Refer to A-(1). 2) Remove the lower unit. Refer t

  • Sharp MX-FNX9, MX-FNX9 ELECTRICAL SECTION 10 – 12 2. Block diagram A. MX-FNX9 Main unit Communi- cation circuit TCKS TLLS TPES TULS STHPS RHDS1 RHDS2 EMPS JHPS1 JHPS2 ENTS RUDS KKBS JIS F_SW DC+24V DC+5V Rush current prevention circuit Sensor I/O circuit CPU EE PROM Driver circuit Stapler unit ST MOT J2 MOT J1 MOT TRY MOT T MOT RO MOT H MOT P_SOL FAN BR_SOL S_SOL F_SOL SW open/close detection circuit 5V power interruption circuit DC+5V Inner finisher Punch unit PBA -CONT TxD RxD DTR DSR RESET DC+24 Drawer connector

  • MX-FNX9 ELECTRICAL SECTION 10 – 9 5) Paper rear edge sensor (FPPEND) and paper horizontal resist sensor (FPPD1 – 6) This circuit is a transmission-type optical sensor circuit using the LED PWB and the photo transistor PWB. Paper is detected when the light path is interrupted by paper passing between the photo transistor PWB and the LED PWB. The light emitt

  • Sharp MX-FNX9, MX-FNX9 ELECTRICAL SECTION 10 – 13 B. MX-PNX1A/B/C/D Punch unit Inner finisher PIS REARS YHPS FULS DC+24V DC+5V Sensor I/O circuit Driver circuit Y MOT PUN MOT Drawer connector PBA-LED PBA-PTR PBA-PUNCH

  • Sharp MX-FNX9, MX-FNX9 ELECTRICAL SECTION 10 – 2 6) Paper surface sensor 2 (FSLD2) The paper surface sensor 2 (FSLD2) employs the photo inter- rupter in which the light emitting diode and the photo transistor are integrated. The paper surface is detected by interruption of lights with the lever-type actuator. Signals are inputted to the CPU (IC10-89pin) through the noise filter of R18 and C6. The logic of the signal inputted to the CPU is H when light is interrupted, and L when light is emitted to the sensor. R10 is the current-limiting

Related Products and Documents (Printer Accessories):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 D-Link DWA140 - RANGE BOOSTER N USB ADAPTOR Technical specifications d-link/dwa140-range-booster-n-usb-adaptor-225.pdf 01 Mar 2023 2 0.76 Mb
2 LG BP335W Owner's manual lg/bp335w-P6X.pdf 09 Nov 2022 57
3 Develop INEO 184 Installation manual develop/ineo-184-1CW.pdf 09 Feb 2024 6
4 LG HBLG1803R Service manual lg/hblg1803r-1QH.pdf 07 Feb 2023 50 2.97 Mb
5 Abit NF7 Operation & user’s manual abit/nf7-M1J.pdf 09 Aug 2022 96 3.69 Mb
6 RCA EZ3000 Important information rca/ez3000-7J1.pdf 11 Oct 2023 2 0.04 Mb

Similar Resources:

  • Ricoh

    3800C

    (2 pages)
    Important❒Check the printer nameplate to confirm the model code.❒If you want to use the optional duplex unit, 2 tray finisher and 4-bin mailbox at the same time, install the optional paper feed unit first, and theninstall these options.❒If you have already installed the optional duplex unit, 2 tray finisher and 4-bin mailbox, remove all these options b …
  • Epson

    Stylus Color 440

    (38 pages)
    EPSON® USB/Parallel Adapter User’s Guide IMPORTANT: To use the USB/Parallel Adapter with your Apple® iMac™, you must download and install the iMac Update 1.0 from Apple at http://swupdates.info.apple.com.CPD 7424R1EPSON Stylus COLOR 440 EPSON Stylus COLOR 800EPSON Stylus COLOR 600 EPSON Stylus COLOR 850EPSON Stylus COLOR 640 EPSON Stylus COLOR 1520EPSO …
  • Konica Minolta

    bizhub 751

    (238 pages)
    Quick Guide [Copy/Print/Fax/Scan/Box Operations]INDEXIntroduction1. Basic operations2. Useful copy operations3. Useful printing operations4. Useful fax operations5. Useful network scan operations6. Useful box operations7. Troubleshooting8. User Settings parameters9. Glossary10. Index …
  • Kyocera

    FS-C5016N

    (16 pages)
    DuplexerUnité de duplexageDuplexeinheitDuplexorUnità duplex両面ユニットOperation GuideManuel d’utilisationBedienungsanleitungGuía de instruccionesGuida operativa使用説明書DU300.fm 1 ページ 2003年4月18日 金曜日 午前10時5分 …
  • Brother

    TN-2410

    (2 pages)
    TNBR2420BK-S1 Octopus Kurzanleitung Brother TN-2410 TN-2420 Kartuschen befüllen 1. Entfernen Sie beide Seitenabdeckungen 2. Zahnrad und Verschluss an der Einfüllseite entfernen 3. Das Zahnrad mit Dichtung entfernen, Resttonerpulver entfernen 4. An der Seite des Tonerförderantriebs das große Zahnrad abziehen 5. Transportrad im Uhrzeigersinn i …
  • Lexmark

    18L0042

    (1 pages)
    CONTENTS:Ink DispensersCyan/Magenta/Yellow3 x 24cc1 CapRemoval Toolfor Lexmark 18L0042 “83” Tri-Color Cartridge ONLY1. Protect work surface.Refilling your cartridge is a clean and simple job, but it is best to coveryour work area with newspaper or other scrap paper to protect fromaccidental ink spills.2. Remove depleted color print cartridge from printe …

Comments, Questions and Opinions: