Manualios.com

PUTHON 5206P Owner's Manual

PUTHON 5206P Manual Online:

4.15, 1619 votes
PUTHON 5206P User Manual
PUTHON 5206P User Guide
PUTHON 5206P Online Manual

Text of PUTHON 5206P User Guide:

  • PUTHON 5206P, 38 © 2012 Directed. All rights reserved. System Expansion Options Controlling two vehicles (Car Select) The Responder LE and 1way companion remote can control systems in two different vehicles saving the need for multiple remote controls. This feature also allows for customized system configurations on each vehicle that has more than one driver. See Owner Recognition follow- ing for details. Owner recognition The system can be configured to recognize the remote used when disarming and change selected features to match the remote users pre

  • PUTHON 5206P, 27 © 2012 Directed. All rights reserved. Table of Zones Zone # (led flashes) Zone Name 1 Trunk 2 Shock Sensor 3 Door 4 Sensor 2 5 Ignition 6 Hood Nuisance Prevention (NPC) NPC monitors all alarm zones and, if any are triggered excessively, bypasses them until corrected. If a point of entry (trunk, hood, door) is left open following a forced entry, it is bypassed. It becomes active again only after being closed. Bypassed sensors automatically reset after one hour and after the vehicle is driven. Disarming then re-arming the alarm does not reset bypassed sensors.

  • PUTHON 5206P, 41 © 2012 Directed. All rights reserved. s Turn Paging off: The remote will not wake up to check for mes- sages with Paging off in the Setup Remote menu. Caution! The remote will not receive trigger messages from the system. s Turn Beeps off: The Button beeps can be turned off in the Setup Remote menu. The command beeps still play normally. Battery Replacement 1. Using a small flat-head screwdriver, insert into slot located on the side of the remote control and carefully pry open the unit. 2. Turn unit over and carefully remove rear housing. Remove the battery from holder and rep

  • PUTHON 5206P, Congratulations Congratulations on the purchase of your state-of-the-art remote start and security system. Reading this Owner’s Guide prior to using your system will help maximize the use of your system and its many features. Please visit: www.pythoncarsecurity.com – For general and additional guide information. For any additional questions please contact your authorized Directed dealer or contact Directed at 1-800-753-0600 (U.S. only). Additional support is also available at: http://support. directed.com. What you get Welcome to the best generation of security with remote start.

  • PUTHON 5206P, 37 © 2012 Directed. All rights reserved. Car Select Car 2 must first be turned On (See Remote Control Configuration sec- tion to turn on). 1. Press and hold the button for 3 seconds. The remote flashes the LED and beeps once or twice to indicate the selected Car is 1 or 2. 2. Release the button for Car Select. 3. Release the button, then press and release while the LED and beeps continue to perform Car Select. Once the car is selected a command can be performed by pressing one of the command buttons.

  • 39 © 2012 Directed. All rights reserved. Driver door priority unlocking The door unlocking operation can be configured to emulate an OEM style of driver priority unlocking for added security during disarming.

  • PUTHON 5206P, 9 © 2012 Directed. All rights reserved. ** Remote Start feature not available when the Remote Start status is incorrect upon receiving the command. (Example: Runtime reset command received when remote start is off). Refer to the notes included in the command descriptions that ad- dress these faults or go to Remote Start Faults under the Remote Start Features section for more details.

  • PUTHON 5206P, 10 © 2012 Directed. All rights reserved. Basic Commands (Direct Access) No Confirmation LEDs on Arm Press and release The alarm arms, doors lock (if connected), and the siren chirps and parking lights flash once. The Arm LED and beeps play to confirm. If Valet mode* is On, the doors lock and the Arm LED, LED and a fault tone plays. Exit Valet mode to arm the alarm normally. If a trigger zone fault is detected the siren chirps once again and the remote will emit a Trigger Zone Fault Report**, the Arm LED, LED and a fault tone plays. To Arm and Panic Press and hold The alarm Arms (or Locks in Valet) and, after 2 seconds, sounds the siren and flas

  • PUTHON 5206P, Safety 45 © 2011 Directed Electronics. All rights reserved. Control Center To satisfy FCC RF exposure compliance requirements, the device and its an- tenna must maintain a separation distance of 20 cm or more from the person’s body, except for the hand and wrists, to satisfy RF exposure compliance. This device complies with the Industry Canada Radio Standards Specification RSS 210. Its use is authorized only on a no-interference, no-protection basis; in other words, this device must not be used if it is determined that it causes harmful interference to services authorized by IC. In addition, the user of this device must accept

  • PUTHON 5206P, 6 © 2012 Directed. All rights reserved. Control Center Control button Status LED The Control Center, typically located on the upper part of the front windshield sends and receives commands or messages to and from your system. It consists of: s The In-vehicle system antenna, for 2 way communication. s The Status LED, as a visual indicator of the system’s status. s The Control button, for placing the system into Valet Mode* and to perform the Emergency Override** operation. * See Remote and System Operations section for details. ** See Alarm Features for details.

  • PUTHON 5206P, 14 © 2012 Directed. All rights reserved. Advanced Commands: (Level 2) Press and release the button 2 times. The and Aux LED’s illumi- nate indicating Level 2 Sensor Bypass Press and release Performing the Sensor Bypass command will incrementally bypass sen- sor operations and be confirmed as follows: s Warn-away bypass: The Parking lights flash 2 times. The Arm LED, 1 beep and 1 fault tone play to confirm. Sensors will be activated for Full Trigger levels of impact only. s Warn-away & Full trigge

  • PUTHON 5206P, 42 © 2012 Directed. All rights reserved. Glossary of Terms Document Terminology Control Module The “brain” of your system. Usually hidden underneath the dash area of the vehicle. It houses the microprocessor which monitors your vehicle and controls all of the system’s func- tions. Responder LE (2-way Remote Control) A hand-held, remote control which operates the various func- tions of your system and receives messages and pages from the system. Companion Remote (1-way Remote Con- trol) A hand-held, remote control which operates the various func- tions of your system but doe

  • PUTHON 5206P, 7 © 2012 Directed. All rights reserved. Using your System Commands and Confirmations Commands, Basic or Advanced, are used to activate system features and are performed by pressing one of the Command buttons. Basic commands control the most often used security and remote start fea- tures while Advanced commands control more specialized features and request reports. Confirmations for Basic or Advanced commands are indicated first by siren chirps and parking light flashes, and then by illuminated con�

  • PUTHON 5206P, 34 © 2012 Directed. All rights reserved. Remote and System Operations Passive Arming* Park and exit the vehicle, after the doors are closed the Passive arm- ing countdown begins. The led flashes quickly and upon reaching 20 seconds the siren then chirps once. At 30 seconds the system arms itself. Anytime before the system arms you can re-enter the vehicle or open the trunk to load or unload items and, after closing passive arm- ing resumes. To stay secure in case of accidental disarming of the system, if a door is not opened within 30 seconds the system re-arms itself and locks the doors. Auto Re-arming* Auto re-arm ensures the vehicle stays protected if it is not entered after

  • PUTHON 5206P, Patent Information This product is covered by one or more of the following United States patents: Remote Start Patents: 5,349,931; 5,872,519; 5,914,667; 5,952,933; 5,945,936; 5,990,786; 6,028,372; 6,467,448; 6,561,151; 7,191,053; 7,483,783 Vehicle Security Patents: 5,467,070; 5,532,670; 5,534,845; 5,563,576; 5,646,591; 5,650,774; 5,673,017; 5,712,638; 5,872,519; 5,914,667; 5,952,933; 5,945,936; 5,990,786; 6,028,505; 6,452,484 Other patents pending.

  • PUTHON 5206P, Safety 47 © 2011 Directed Electronics. All rights reserved. Before remote starting a manual transmission vehicle, be sure to: s Leave the vehicle in neutral and be sure no one is standing in front or behind the vehicle. s Only remote start on a flat surface s Have the parking brake fully engaged WARNING! It is the responsibility of the owner to ensure the parking/emer- gency brake properly functions. Failure to do so can result in personal injury or property damage. We recommend the owner have the p

  • 44 © 2012 Directed. All rights reserved. Government Regulations This device complies with Part 15 of FCC rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. This equipment has b

  • PUTHON 5206P, 18 © 2012 Directed. All rights reserved. Advanced Commands: (Level 4) Press and release the button 4 times. The , Aux, Remote Start and Disarm LED’s illuminate indicating Level 4 Full Silent Arm* Press and release The alarm arms, doors lock, and the siren chirps and parking lights flash 4 times. The Arm LED, 1 beep and 4 fault tones play to con- firm. Defogger** Press and release Activates the vehicle Defogger circuit (if connected) while Remote Start is activated and the parking lights flash 3 times. Th

  • PUTHON 5206P, 21 © 2012 Directed. All rights reserved. second lapse between buttons presses to prevent unintentional opera- tions. If a button is pressed when locked the LED and a fault tone play as an alert. The 1-way remote control only emits the fault tone if equipped with speaker otherwise the 1-way remote control does not respond with any button press. To unlock the buttons, press the button followed by the button. Remote Beep Options: On, Off. The 2-way and 1-way (if equipped with speaker) remote controls emit a beep as a confirmation when a button on the remote is pressed and the 2-way remote also gives a

  • PUTHON 5206P, 31 © 2012 Directed. All rights reserved. Note Temperature report must be turned on by an authorized Di- rected dealer. Remote Start Time-out Alert During remote start a message is sent three minutes before and again at one minute before the engine turns off. The LED, Remote Start LED flash and several tones play as an alert to reset the runtime if desired. Manual Transmission Start (MTS mode) When installed into a manual transmission vehicle, the system requires that the MTS mode is properly set when parking. If MTS mode is not properly set or is defeated after being properly set the system wil

  • PUTHON 5206P, 50 © 2012 Directed. All rights reserved. ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE UNIT. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES,

  • 20 © 2012 Directed. All rights reserved. Responder LE The confirmation LED on each corresponding button indicates the fea- ture setting. Feature Button Press LED on LED off LED Single Flash LED Double Flash Keypad Lock Auto Off Remote Beeps Beeps On Beeps Off Triggers only Car 2 Car 2 On Car 2 Off Page Mode* AUX Paging On Paging Off Power Save1 Power Save 2 1-way comp

  • Important information Government Regulations and Safety information Read the Government Regulations and Warning! Safety First sections of this manual prior to operating this system. Warning! Failure to heed this information can result in death, personal injury or property damage and may also result in the illegal use of the system beyond its intended purpose. Your Warr

  • PUTHON 5206P, 13 © 2012 Directed. All rights reserved. AUX 1 Press and release AUX Activates (or if On, deactivates) the Aux 1 output. The Aux LED and On tones or Off tones play to confirm. Temperature Request Press and hold the button Requests the vehicle’s interior temperature and displays it by illuminat- ing the green confirmation LEDs; cold is 1 LED, cool (2), warm (3), warmer (4) . * See Remote and System Operations section for details. ** See Alarm Features for details.

  • Alarm Features ................................................................................................. 24 Normal Arm Protection ....................................................................... 24 Sensor Silent Arm protection ............................................................... 24 Full Silent Arm Protection .............................................

  • PUTHON 5206P, 36 © 2012 Directed. All rights reserved. Out of Range Each time a command is performed the Responder LE will expect a command confirmation from the system. If a command confirmation is not received the and transmit LED’s flash and a long fault tone plays as an alert. No Remote Output Occasionally when a command is performed the remote may not generate a command confirmation output or Out of Range output. This indicates that the system received the command but it was an incomplete command (e.g. Aux button pressed too short to activate the trunk release) or it was an illegal message (e.g. the command was corrupted due to local RF interference). These are temporary

  • PUTHON 5206P, Warning! Safety First ......................................................................................... 46 Installation ........................................................................................ 46 Remote Start Capable ........................................................................ 46 Manual Transmission Vehicles ............................................................. 46 Interference ....................................................................................... 48 Upgrades ......................................................................................... 48 Water/Heat Resistance ........................................................

Related Products and Documents (Car Alarm):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 True Fitness TCM-78AC Installation manual true-fitness/tcm-78ac-2-MJ5.pdf 07 Jan 2023 16 0.72 Mb
2 Harbor Freight Tools 47274 Assembly and operation instructions manual harbor-freight-tools/47274-QR8.pdf 25 Sep 2022 9
3 Lexicon GX-7 Specifications lexicon/gx-7-WAK.pdf 21 Jun 2022 4
4 HP StorageWorks 8/24 - SAN Switch Hardware reference manual hp/storageworks-8-24-san-switch-T2T.pdf 22 Nov 2023 84 4.55 Mb
5 Onkyo A-905TX Instruction manual onkyo/a-905tx-4L8.pdf 15 Nov 2023 28
6 Delta TP305 Instruction manual delta/tp305-X6Z.pdf 29 Jan 2023 48 9.83 Mb

Similar Resources:

  • Code Alarm

    ca5153

    (30 pages)
    12012 Audiovox Electronics Corporation. All rights reserved.PROFESSIONALSERIESAutomatic / Manual TransmissionRemote Start with Keyless EntryInstallation Guidefor models:ca5153ca5153sst …
  • Clifford

    400

    (12 pages)
    Complete Owner’s ManualThe Science of Security™USA HeadquartersCanada HeadquartersUK HeadquartersGermany HeadquartersMexico Headquarters20750 Lassen Street Chatsworth, California 913111-800-CLIFFORD or 1-800-824-3208 or 1-818-709-75514513 Dobrin Street Montreal, Quebec H4R 2L81-800-361-3444 or 1-514-332-4444Boundary Business Court92/94 Church Road Mitcha …
  • Fortin

    EVO-ALL

    (39 pages)
    Service No : 000 102 04 2536Date: xx-xxINTERFACE MODULEMade in CanadaPATENTS PENDING US: 2007-228827-A1www.fortinbypass.comHARDWARE VERSION FIRMWARE VERSION Module label | Étiquette sur le moduleNotice: Updated Firmware and Installation GuidesUpdated ¿ rmware and installation guides are posted on our web site on a regular basis. We recommend that yo …
  • Ford

    Automobile

    (30 pages)
    Owner's ManualManual del propietarioGuide de l’utilisateurVehicle Security and Remote Start SystemsDeluxe Vehicle Security System with Keyless EntryTMFeaturing PowerCode Technology For the Ultimate in Comfort, Convenience and SecurityTM101822-510/02Sistema de seguridad para vehículos de lujo con acceso sin llaveSystème antivol de voiture de luxe …
  • AutoCommand

    28623T

    (20 pages)
    v5.3 S286231© 2005 Directed Electronics, Inc. OEM SERIESRemote Control Car Starter Installation Manual for Model # 28623TPLEASE READ COMPLETELY BEFORE BEGINNINGCongratulations on your purchase of the AutoCommand® OEM Series Remote Car Starter. The AutoCommand® OEM Series Remote Car Starter system allows you to start the carby remote control from the comf …
  • Mopar

    82209700

    (24 pages)
    INSTALLATION INSTRUCTIONSProfessional Installation is RecommendedTechnical SupportFor Authorized Dealers - (800) 34-MOPARHours: 9:00 a.m. - 6:00 p.m. EST Monday thru Friday 10:00 a.m. - 2:00 p.m. EST Saturday1030782REV. A9/05K6859675Note: Both Factory RKE Keyfobs are required foroption programming & Driver’s Door Priority Unlockfeature must be enab …

Comments, Questions and Opinions: