Manualios.com

SurgeX SU-2000Li Operation & User’s Manual

SurgeX SU-2000Li Manual Online:

4.15, 1477 votes
SurgeX SU-2000Li User Manual
SurgeX SU-2000Li User Guide
SurgeX SU-2000Li Online Manual

Text of SurgeX SU-2000Li User Guide:

  • SurgeX SU-2000Li, © 2011 SurgeX 1noitcudortnI.1 2. Controls and Indicators 5 8noitallatsnI.3 11noitarepO.4 14gnitoohselbuorT.5 15yrettaB eht gnicalpeR.6 18ecivreS gniniatbO.7 19snoitacificepS.8 9. Configurable Parameters & Settings 21 10. Limited Product Warranty 22 TABLE OF CONTENTS

  • SurgeX SU-2000Li, IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS ! Thank you for purchasing this power protection product. It has been designed and manufactured to provide many years of trouble free service. This symbol indicates "ATTENTION" This symbol indicates "Risk of Electrical Shock" This symbol indicates "Alternating Current Supply" This symbol indicates "Alternating Current Supply Phase" INTRODUCTION 1 1

  • SurgeX SU-2000Li, WARNING: Risk of Electrical Shock. Hazardous live parts inside these power supplies are energized from the battery even when the AC input is disconnected. CAUTION! To de-energize the outputs of the UPS: 1. If the UPS is on press and release the On/Off/Test button. 2. Disconnect the UPS from the AC wall outlet. 3. To de-energize the UPS completely, disconnect the battery. CAUTION! To reduce the risk of electrical shock in conditions where the load equipment grounding cannot be verified, disconnect

  • SurgeX SU-2000Li, After removing your UPS from its carton, it should be inspected for damage that may have occurred in shipping. Immediately notify the carrier and place of purchase if any damage is found. Warranty claims for damage caused by the carrier will not be honored. The packing materials that your UPS was shipped in are carefully designed to minimize any shipping damage. In the unlikely case that the UPS needs to be returned to the manufacturer, please use the original packing material. Since the manufacturer is not responsible for ship- ping damage incurred when the system is returned, the original packing mate- rial is inexpensive

  • SurgeX SU-2000Li, Life Support Policy As a general policy, we do not recommend the use of any of our products in life support applications where failure or malfunction of the product can be reason- ably expected to cause failure of the life support device or to significantly affect its safety or effectiveness. We do not recommend the use of any of our prod- ucts in direct patient care. We will not knowingly sell our products for use in such applications unless it receives in writing assurances satisfactory to us that (a) the r

  • SurgeX SU-2000Li, The AC normal (green) LED illuminates in a steady state when the UPS is on and operating in the AC normal mode. The AC normal LED will extinguish when operating in the Battery mode. The On-Battery (green) LED illuminates in a steady state when the UPS is operating in the Battery mode. The On-Battery LED will extinguish when operating in the AC normal, Boost and Buck modes. The Boost (yellow) LED illuminates in a blinking state when the UPS is operating in the Boost mode. The Boost LED will extinguish when operating in the AC normal, Buck and Battery

  • SurgeX SU-2000Li, The Load Level Bar Graph (AC mode only) operates as follows: LED #10: >10% load (green/red/yellow) LED will be green and illu- minated when there is at least 10% of the rated capacity. LED #30: >30% load (green/yellow) LED will be green and illumi- nated when there is at least 30% of the rated capacity. LED #50: >50% load (green/yellow) LED will be green and illumi- nated when there is at least 50% of the rated capacity. LED #70: >70% load (green/yellow) LED will be green and illumi- nated when there is at least 70% of the rated ca

  • REAR PANEL Output Power Receptacles Model # SU-2000Li NEMA 5-20P 6-NEMA 5-15/20R 1-NEMA L5-20R Input Power Plug (All power cords are 10ft) 1. The RS232 Communications Interface Port is for UPS monitoring and control. 1. The RS232 Communications Interface Port is for UPS monitoring and control. 2. The USB Communications Interface Port is for UPS monitori

  • SurgeX SU-2000Li, CONNECTING THE BATTERIES (QUALIFIED SERVICE PERSONNEL ONLY) Please read all of the WARNINGS and CAUTIONS before attempting to con- nect the batteries. 1. Remove the UPS from the shipping box and set on the floor or a bench top. 2. Remove the front panel retaining screws. 3. Lay the front panel on top of the UPS. 4. Verify proper polarity. Connect the battery connectors (red and black) toge- ther. NOTE: Some sparking might occur, this is normal. 5. Re-install the front panel onto the UPS. 6. Re-install the front panel retaining screws. 7. Continue with the rest of the Installation. INSTALL

  • SurgeX SU-2000Li, RACKMOUNT CONFIGURATION This UPS comes with mounting brackets for the standard 19" (46.5cm) rack. The mounting brackets to fit a 23" (59.2cm) standard rack are also available. The screws for mounting the UPS to the rack are not included (screw size varies with rack size). 1. Locate the mounting bracket screw holes on the side panels of the UPS, at the front of the UPS. NOTE: The mounting brackets can also be mounted in the middle of the UPS. 2. Align the mounting bracket with the

  • SurgeX SU-2000Li, CHARGING THE BATTERY CHECKING THE SITE WIRING FAULT (120V Models) After plugging in the UPS, check the Site Wiring Fault (SWF) LED on the front panel of the UPS. If the SWF LED is illuminated, the UPS is plugged into an improperly wired AC outlet. If the UPS indicates a Site Wiring Fault (SWF), have a Qualified Electrician correct the problem. COMMUNICATIONS PORT CONNECTION (OPTIONAL) The Power Monitoring Software and interface cables can be used with the UPS. Use only the interface cables that come with these UPSs. Connect the inter- face cable (Serial or USB) to the

  • SYSTEM OVERVIEW This Line-Interactive UPS protects computers, internetworking, and telecom- munications equipment from blackouts, brownouts, overvoltages, and surges. The AVR function continuously corrects the voltages, in-between the brownout and overvoltage transfer points (80 - 164VAC/150 - 271VAC), to a safe usable level. When the UPS is operating in the AVR mode the audible alarm wil

  • SurgeX SU-2000Li, COMMUNICATIONS PORTS (RS232 and USB) The RS232 communication port is a standard DB9 female with both RS232 and simulated contact closure capability. The UPS will poll the port and activate the port for RS232 or contact closure in accordance with the type of cable it finds connected to the port. To change the port configuration requires the unit be turned off and restarted with the desired cable connected. The pinout for the port is depicted per the chart below: Pin 1: Simulated contact closure Low Battery Warning, NO Pin 2: /TXD Pin 3: /RXD and recei

  • SurgeX SU-2000Li, WEAK/BAD BATTERY The UPS automatically tests the battery’s condition and will illuminate the Weak/ Bad Battery LED and sound the alarm. This alarm will be repeated until the batteries pass a self test. If the battery is weak, bad or disconnected, the Weak/Bad Battery LED will illuminate and the alarm will beep three times every five-minutes until the battery is reconnected or replaced. It is recommended that the UPS be allowed to charge overnight before performing a battery test to confirm a Weak/Bad Battery condition. NOTE: If the UPS has a Weak/Bad Battery Alarm after reconnecting or replac- ing the batteries, the user must

  • SurgeX SU-2000Li, Possible Cause Symptom What To Do Press and release the On/Off/ Test button to start UPS On/Off/Test button not pushed UPS will not turn on Reset circuit breaker by pressing the plunger back in. If the AC circuit breaker trips after UPS starts up, reduce the load on the UPS UPS operates in battery mode only, even though there is normal AC present Input AC circuit breaker is tripped UPS has detected an internal fault Call for service Fault LED is illuminated The AC normal LED is illuminated, but there is no out- put Incorrect service wiring Disc

  • SurgeX SU-2000Li, REPLACING THE BATTERY WARNING! This Uninterruptible Power Supply contains potentially hazardous voltages. Do not attempt to disassemble the UPS beyond the battery replacement procedure. This UPS contains no user serviceable parts. Repairs and Battery replacement must be performed by QUALIFIED SERVICE PERSONNEL ONLY. Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes and may be toxic. CAUTION: (QUALIFIED SERVICE PERSONNEL ONLY) CAUTION: Do not dispose of ba

  • SurgeX SU-2000Li, BATTERY REPLACEMENT PROCEDURE PLEASE READ THE CAUTIONS AND WARNINGS BEFORE ATTEMPTING TO REPLACE THE BATTERIES Hot-swappable batteries mean that the batteries can be replaced without powering down the whole UPS system. NOTE: If there is a power interruption while replacing the hot-swappable batter- ies, with the UPS on, the load will not be backed up. To hot-swap the batteries start with step number 6. 1. Turn off the equipment that is plugged into the output receptacles of the UPS. 2. Press and release the On/Off/Test button on the front panel to turn the UPS OFF. NOTE: Turn the input circuit breaker to the off position for the 208V models.

  • 8. Remove the two retaining screws for the battery retaining bracket. (FIG. 3) 9. Remove the battery retaining bracket. (FIG. 3) 10. Disconnect the Battery connectors (red and black). (FIG. 4) 11. Grasp the battery pull tab and gently pull the battery module out of the UPS and set on the floor. (FIG. 4) NOTE: Use Caution, the battery module is heavy. 12. Disconnec

  • IF THE UPS REQUIRES SERVICE 1. Use the TROUBLESHOOTING section to eliminate obvious causes. 2. Verify there are no circuit breakers tripped. A tripped circuit breaker is the most common problem. 3. Call your dealer for assistance. If you cannot reach your dealer, or if they cannot resolve the problem call or fax the Technical Support department at 1-800-645-9721. Please have the fo

  • SurgeX SU-2000Li, Default: 120VAC, User selectable: 127VAC Protection Waveform Type Over-Current, Short-Circuit Protected and Latching Shutdown Sine Wave Frequency 50/60Hz, +/-0.1Hz (unless synchronized to utility) Nominal Voltage Maximum Power Capacity 2-6 ms Typical >93% (Full Load) Resettable Circuit Breaker 50 or 60 Hz, +/-6Hz, autosensing 0 - 165VAC 80 - 164VAC 120VAC: 105 - 134VAC Transfer Time Efficiency (Line Mode) Input Protection Frequency Limits Voltage Range Acceptable Input voltage SYSTEM SPECIFICATIONS Voltage Range Topology Line-Interactive, Sine Wave OUTPUT NON-BATTERY OPERATION INPUT 1( elgniSesahP fo rebmuN ∅ 2W +

  • SurgeX SU-2000Li, BATTERY SYSTEM Typical Recharge Time Typical Battery Life Battery: Quantity/Rating 3-5 years, depending on discharge cycles and ambient temp 8-hours from total discharge 6-12V7.2Ah Battery Type Sealed, Non-Spillable, Maintenance Free, Value Regulated Lead Acid System Voltage 72VDC Runtime: Full Load (minutes) Runtime: Half Load (minutes) 13 5 SURGE PROTECTION AND FILTERING Audible Noise at 1 m (3 ft.) 10/100 Base-T surge protec- tion let-through (as a percent- age of an applied +/-6 kV 1.2/ 50 us, 500 a 8/20 uS test) Telephone line surge protec- tion let-through (as a percent- age of an applied +/-6 kV 1.2/ 5

  • (These items may require optional software or hardware) Function Factory Default Description User Choices Set inverter output voltage Shut- down Type Set audible alarm state Enable/ Disable auto restart Battery life in days Battery install date UPS ID Enterprise Plus Series Date of manufacture 1826 Enabled Enabled Entire UPS 120VAC Up to 64 charac- ters to define the UPS Date of batt

  • SurgeX SU-2000Li, For a period of 11 years from the date of your purchase of any SurgeX product, SurgeX warrants the product against defects in materials used by SurgeX or workmanship performed by SurgeX (a "Covered Product"). SurgeX's obligations with respect to a Covered Product are to provide, at no charge, all labor and parts (either new or rebuilt, as determined in SurgeX's sole discretion) necessary for the repair of the Covered Product. If SurgeX, in its sole discretion, determines that a Covered Product is not repairable,

Related Products and Documents (UPS):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 VTech DS6641 Operation & user’s manual vtech/ds6641-Y53.pdf 26 Feb 2023 16 5.28 Mb
2 Water Control Corporation BrassMaster plus+ Installation & operation manual water-control-corporation/brassmaster-plus-7DU.pdf 22 Dec 2023 8
3 AT&T 1445 Operation & user’s manual at-t/1445-2H2.pdf 23 Aug 2023 17 0.31 Mb
4 Zte ZTE-C X768 Operation & user’s manual zte/zte-c-x768-22X.pdf 13 Jan 2024 90
5 Nice OX4T Programming manual nice/ox4t-WY5.pdf 13 Jul 2022 3
6 Ferris ProCut S Series Operator's manual ferris/procut-s-series-7TE.pdf 05 Jul 2022 44

Similar Resources:

  • Tripp Lite

    SMART2200RM2UL

    (60 pages)
    1Owner’s Manual1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/supportCopyright © 2016 Tripp Lite. All rights reserved. SmartPro® is a registered trademark of Tripp Lite.Español 21Français 41SmartPro® 2U RackmountIntelligent, Line-Interactive UPS System (with Lithium Iron Phosphate Battery)120V Sine Wave Output • 2200VA CapacityMo …
  • Tecnoware

    EASY Power 900

    (4 pages)
    IT IS ADVISED TO READ THIS MANUAL CAREFULLY AND TO KEEP IT ! Thank you for choosing Easy Power. This UPS (Uninterruptible Power Supply) provides a perfect protection to all feeding devices. This manual is a guide which enables you to correctly install and use your UPS. This manual includes important SAFETY instructions for the operator, for the UPS correct i …
  • Marathon Power

    vault series

    (36 pages)
    9DXOW6HULHV7UXH2Q/LQH'RXEOH&RQYHUVLRQ8QLQWHUUXSWLEOH3RZHU6XSSO\86(50$18$/)2502'(/69$9$ …
  • MetaSystem

    Whad 1500

    (48 pages)
    ITENFRDEPTManuale d’uso per l’utenteUser’s ManualManuel d’installation et d’utilisationBedienungsanleitung für den BenutzerManual do utilizadorWhad 1500 - 2000- 2500GRUPPI DI CONTINUITÀUNINTERRUPTIBLE POWER SUPPLIESONDULEURS UNTERBRECHUNGSFREIEN STROMVERSORGUNGENV81608AV81608A Ist.Uso Whad2000:V81608A Ist.Uso UPS Whad2000 8-04-2008 9:52 Pagina …
  • IBM

    5000XHV

    (14 pages)
    1 5000XHV - UNINTERRUPTIBLE POWER SUPPLY - QUICK INSTALLATION GUIDE 46M5391 1: OVERVIEW ATTENTION: • Read the Safety Instructions before installing the uninterruptible power supply. • The uninterruptible power supply and battery modules are heavy. Select a location sturdy enough to handle the weight. • Refer to the Uninterruptible Power Supply Ope …
  • MGE UPS Systems

    EX 5RT

    (8 pages)
    www.mgeops.comEX RT Transformer ModuleQuick StartStandard Features◗ When used with standardsystem, EX RT TransformerModule provides isolatedand Step-down 120/208/240 Vac outputs.◗ Multiple Output receptacles:120/208/240 Vac. …

Comments, Questions and Opinions: