Manualios.com

Printrbot Simple Getting Started Manual

Printrbot Simple Manual Online:

3.6, 2003 votes
Printrbot Simple User Manual
Printrbot Simple User Guide
Printrbot Simple Online Manual

Text of Printrbot Simple User Guide:

  • Printrbot Simple, Print not correct size (G-Code) Verify values for X,Y,Z by typing command M501. Values should be X119 Y119 Z2020 E100. If for some reason values are not this, change with G-code command M92 X119. Save settings on rmware with M500 command. Type M501 to verify change has been made. Other Problems For more in depth calibration troubleshooting, please review the Hardware Calibration and other settings in our original Getting Started Guide - Version 1 http://bit.ly/YX8nct For all other issues, please visit our technical forum at www.pr

  • Printrbot Simple, Contents 4 Chapter 1: Welcome 4 Overview 4 Support 5 Chapter 2: Your Printrbot has arrived... now what? 5 Printrbot Kits 5 Pre-Assembled Printrbots 6 Chapter 3: Building your Printrbot 6 Required and optional tools 6 Assembly instructions 6 Help during assembly 7 Chapter 4: Install Software 8 Chapter 5: Connect your Printrbot 9 Chapter 6: Congure Software 9 Congure Repetier printer settings 9 Connection 10 Behavior 10 Dimension 11 Congure Slic3r settings 11 Layers and perimeters 12 Inll 12 Skirt and brim 13 Filament 14 General 14 Extruder 1 15 Your saved selections 16 Chapter 7: Functional Pre-Print Test 16 Connect to the printer 16 Test the

  • Printrbot Simple, Advanced Printing 9 Now that you have done some basic prints, where do you go from here? Well, your journey has just begun as there are lots of advanced techniques for printing highly precise and complex prints; such as micro sized prints and complex objects. Technical Forums Please visit our technical forum at www.printrbottalk.com as we have several power users that have pushed the limits on what is possible with a 3D printer. They will be able to give you suggestions and advice on how to successfully print even the most complex objects. Community We also suggest checking out www.reprap.org and interacting with the rest of the 3D community. Their community portal and New

  • General Make sure your bed size is set to 100mm and 50mm center points. Mac Windows Extruder 1 Standard tip size with all bots is currently 0.4 mm. Otherwise enter the appropriate diameter to match the tip you are using. Save your settings. Mac Windows 14

  • Printrbot Simple, Welcome 1 Read this guide to learn about your Printrbot, how to make your rst 3D print, and more. Overview The purpose of this guide is to get you printing your 3D models as soon as possible! Whether you have a pre-assembled Printrbot or a build it yourself kit, this guide will walk you through the necessary steps to a successful rst print. So let’s get going! Support If at any time you need help or get stuck, please check our FAQ page and then open a support ticket if necessary. www.printrbot.com/support/ 4

  • Printrbot Simple, Connect When the slice has completed, click on the Connect button. Set Temperatures Next up , you need to set the extruder temp. Click on the Print Panel and scroll down to set the temperatures (Extruder 195 for PLA and Heated bed 0) be sure to click the Set buttons. Also, please note that you should now have a green connect button to indicate that you are connected to your computer. Temperature Curve Now click on the Temperature Curve and watch the graph as the extruder and heat bed rise in temp. You need to make

  • Printrbot Simple, Connect your Printrbot 5 1. Find a secure table or at surface on which to print. 2. Place your printer close to your computer and plug in the power source for your bot. 3. Plug in the mini USB cable to the back of your Printrbot and connect the other end to a USB port on your computer. 4. You should now have the Printrbot powered on and connected to your computer. 8

  • Printrbot Simple, Functional Pre-Print Test 7 Before testing your rst print, you need to make sure all of your axis are working as expected on your bot. Connect your printer to your computer and make sure both of them are powered on. Connect to the printer Click on the Connect button and it should turn green to indicate your are properly connected Test the Z axis Click on both the 10 and -10 buttons for the Z axis. Your extruder should be able to move up and down freely. Mac Windows 16

  • Printrbot Simple, 19 Chapter 8: Printing your First 3D Model 19 Download le 19 Add .STL le 19 Scale your 3D model 20 Slice 21 Connect 21 Set temperatures 21 Temperature curve 21 Run 21 After the print completes 21 Congratulations 22 Chapter 9: Advanced Printing 22 Technical Forums 22 Community 23 Chapter 10: Common Issues and Troubleshooting 23 Filament is not extruding 23 Print not sticking to bed 23 Head is dragging across the print 24 Print not correct size (G-Code) 24 Other problems

  • Printrbot Simple, Congure Software 6 The following settings are recommendations for your rst prints. Over time you can change and modify them as you get more familiar with your printer as different 3D models often require different settings for a more accurate and precise print. The reason for this is that your 3D printer is more like a tool than an appliance. Every 3D model is unique and often requires a different “tool” to get the job done. So you will nd over time that certain settings work better than others. It’s also worthy to note that the printers themselves often have thei

  • Your Printrbot has Arrived... now what? 2 The arrival of your bot can not only be exciting, but we realize it can be overwhelming at rst. If you have received an assembled bot, your work is already nearly done. However, those with a kit have a little bit more work to do. But fear not, our support team is here to help and we will make sure you are printing in no

  • Printrbot Simple, Behavior Set the extruder temperature to 200 and the heated bed to 0 degrees. Travel Feedrate should be 4800 and check the following boxes. Mac Windows Dimension Set all print area settings to 100mm. Click Apply and then OK. Mac Windows 10

  • Printrbot Simple, Printing your First 3D Model 8 Now that your bot is assembled, connected to your computer, and the software installed - it’s time to run your rst test print! Download File Go towww.thingiverse.comand nd something to print. For your rst print, we recommend either the5mm Calibration CubeorMr. Jaws. Click on the big blue Download button and select either an individual le or the entire zip le.  Add STL File After you have downloaded a model, open Repetier and add the .STL le Mac Windows Scale Your 3D Model Depending on the size of your 3D Model you may need to resize it. Look at the 3D image in the Repeti

  • Test the extruder with initial burn-in temperature Set your Extruder temperature to 200 and click Set. When the temp has reached 200, open the extruder latch and feed the lament down into the hot end opening at the hobbed bolt area. For easier access, we recommend trimming the lament at an angle. Troubleshooting If you encounter any movement issues with your axis or ex

  • Printrbot Simple, Building your Printrbot 3 Required and optional tools Before you begin to assemble your bot, please note that you are going to need several tools. Below is a listing of the typical tools used for assembling a Printrbot Plus. This list should cover you for both the LC and jr as well, however there may be a few other items you will need to purchase depending on which version Printrbot you have. Required Tools Optional Tools Phillips Screwdriver 8mm or 5/16 inch Wrench 1/2 inch Wrench 2.5mm Allen Wrench 1.5mm Allen Wrench Hammer or Rubber Mallet Wood or Supe

Related Products and Documents (3D Printers):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Bertazzoni M93V Installation, maintenance and use instructions bertazzoni/m93v-52I.pdf 20 Sep 2023 16 0.51 Mb
2 Firefly glowPhone Operation & user’s manual firefly/glowphone-Q3S.pdf 22 Nov 2023 43 0.85 Mb
3 AWA PCD-792 Instruction manual awa/pcd-792-8NL.pdf 26 Oct 2022 13 0.56 Mb
4 McAfee VIRUSSCAN 5.1 Administrator's manual mcafee/virusscan-5-1-66F.pdf 26 Oct 2023 140
5 SEVERIN KS 9761 Datasheet severin/ks-9761-53E.pdf 18 Jan 2023 1 0.7 Mb
6 La Crosse Technology Wireless Weather Station Instruction manual la-crosse-technology/wireless-weather-station-O5B.pdf 25 Nov 2023 30

Similar Resources:

  • Renkforce

    1538778

    (22 pages)
    ServiceanleitungThermistor mit Heizperle für RF100Best.-Nr. 1538778 Seite 2 - 11Replacement instructionsThermistor with heater for RF100Item No. 1538778 Page 12 - 21 …
  • Fusion3 Design

    F306

    (42 pages)
    1 Operation Guide F306 Generation I Revision 4 | 08-27-2014 Table of Contents 1. Introduction ................................................................................................................................................................... 2 1.1. Warnings ................................................................................ …
  • TRAK

    3ntr Series

    (128 pages)
    TRAK® 3ntr 3D Printers Printer & MMS Initial Set-Up & Calibration Guide Covers Current Models: • 3ntr A2 • 3ntr A4 • 3ntr MMS v1/v2 2615 Homestead Place Rancho Dominguez, CA 90220-5610 USA T | 310.608.4422 | F | 310.764.2668 Service Department: 800.367.3165 e-mail: [email protected] | [email protected]
  • Tumaker

    NX PRO DUAL

    (15 pages)
    NX PRO DUALUSER MANUALÍndEXPrinter Specications ................................... 2Main parts of the printer ................................ 3Elements included in the printer .................... 3Installation and set up ................................... 4Quick guide ................................................... 6Calibrate dual height......... …
  • Geeetech

    Rostock mini

    (31 pages)
    1 / 31 http://www.geeetech.com Rostock mini Hardware Build Manual Some printed parts may have unsmooth edge, you can scrape them with the file. Some screw holes also have to be expanded for assembly. I. Pre-assembly of extruder …
  • Z Corporation

    Z 406

    (157 pages)
    Z406 System User Manual September 2004 © 2003-2004 Z Corporation Part Number 09520 Z®406 3D Color Printer User Manual Z Corporation Type II Revision D …

Comments, Questions and Opinions: