Manualios.com

socomec Masterys BC Installation And Operating Manual

socomec Masterys BC Manual Online:

4.5, 1169 votes
socomec Masterys BC User Manual
socomec Masterys BC User Guide
socomec Masterys BC Online Manual

Text of socomec Masterys BC User Guide:

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 45 ENGLISH 10.6.2 Protection on a UPS without auxiliary mains supply. Activating UPS protection on the mimic panel: access the Congurations menu on the mimic panel (see the Congurations Menu under the Service Menu section of the manual) and set the BACKFEED TYPE parameter to 3.BYPASS-INPUT Common. Diagram of Principle. OPTIONS 10 Note. The neutral is not disconnected as, even in the event of a single fault on the UPS, it never has high potential when the mains and/or auxilia

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 26 ITALIANOENGLISH Meaning of the status light bar Colour Condition displayed RED ashing Imminent shutdown alarm (the load will be disconnected in a few minutes) RED Load not powered or battery circuit open YELLOW ashing Alarm indicating request for ordinary maintenance after over 25.000-30.000 hours of operation according to conditions of use (type of load, temperature), (L7 ashing and alarm A44) UPS in stand by YELLOW Load on battery or battery discharging if LED 2 is on steady YELLOW On automatic bypass if LED 5 is on steady YELLOW End of F

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 10 ITALIANOENGLISH UNPACKING AND INSTALLATION OF THE UNIT 3 3.2.2 Models “T” (h 1.400 mm). 3.2.2-9 3.2.2-6 Loosen screws B. Remove screws C. 3.2.2-7 Tighten screws B. 1 B 2 C 2 B 1 1 The UPS can be moved. Place the UPS in the installation area. 3.2.2-8 Secure the UPS with feet D. D D Secure the UPS with feet D only when it is in position with the cable connected. Loosen screws B. 1 B 2 2 3.2.2-4 1 3 2 3.2.2-5 Remove screws A. 1 A 2 3.2.2-23.2.2-1 3.2.2-3 Remove screws A and screws B. A B

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 16 ITALIANOENGLISH 3.6 CONNECTION OF THE GENERATOR. If your system uses a generator, connect the “generator set ready” no-potential contact to connector IN 2 on the optional ADC card congured in standard or power safe mode (see paragraph 10.1). This automatically extends the voltage and frequency value range when power is supplied by the generator set. 3.7 EXTERNAL E.S.D. CONNECTION. A remote emergency shutdown system (E.S.D.) can be installed by means of the optional ADC card; see para- graph 10.1. Connect a normally closed zero-po

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 34 ITALIANOENGLISH 8 COMMUNICATION 8.2 ACCESSORIES AND SW OPTIONS. A large number of SW solutions can be adopted on MASTERYS TM thanks to its advanced communication facili- ties. These solutions have been specially designed for the ecient management of power protection devices. UNI VISION PRO is the solution for managing a UPS connected to the local server via RS232 interface or via LAN network. It is normally used at depart- mental level to automatically shutdown the systems and ensure secure control of the UPS that in turn protect servers an

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 47 ENGLISH TECHNICAL SPECIFICATIONS 11 Dimensions 444 795 800 444 795 1.000 444 795 1.400 Mechanical characteristics with standard batteries Model Input/Output kVA Dimensions Weight (LxPxH mm) (kg) MAS2BC115S+C1 3/1 15 444x795x800 195 MAS2BC115M+D1 3/1 15 444x795x1.000 235 MAS2BC115M+C2 3/1 15 444x795x1.000 300 MAS2BC115T+C3 3/1 15 444x795x1.400 415 MAS2BC115T+C4 3/1 15 444x795x1.400 520 MAS2BC120M+D1 3/1 20 444x795x1.000 240 MAS2BC120M+C2 3/1 20 444x795x1.000 310 MAS2BC120T+D2

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 20 ITALIANOENGLISH MODES OF OPERATION 4 4.3 OPERATION WITH MANUAL MAINTENANCE BYPASS. If the maintenance bypass is activated using the appropriate procedure, the load is powered directly from the maintenance bypass, while the UPS is separated from the power supply and can be switched o. This operating mode can be selected for maintenance to be carried out on the system so that the necessary actions can be performed by service personnel without having to disconnect the power supply to the load. 4.4 OPERATION WITH EXTERNAL MANUAL BYPASS (optional). The ext

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 37 ENGLISH 9 PROBLEM SOLVING • A38, A39, A40, A41: external alarm 1, 2, 3, 4. One of the ADC card inputs has been activated; check the situation of the devices connected to this card. • A56, A57: generator general alarm. The generator has sent an alarm; check directly on the GE. • A61: wrong phase cycle direction. The phase cycle sequence is incorrect. In this case, invert two phases of the input mains. For a UPS with sepa- rate auxiliary mains, exchange the two phases of the

  • MASTERYS BC from 15 to 20 kVA 8 ITALIANOENGLISH The packaging guarantees the stability of the UPS during shipping and physical transfer. Carry the packaged unit as close as possible to the installation site. When moving the unit on even slightly sloping surfaces, use the blocking equipment and breaking devices to ensure that the unit does not fall over. 3.1 SHI

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 44 ITALIANOENGLISH OPTIONS 10 10.6.1 Protection on the separate auxiliary mains. Activating UPS protection on the mimic panel: access the Congurations menu on the mimic panel (see the Congurations Menu under the Service Menu section of the manual) and set the BACKFEED TYPE parameter to 1.BYPASS. Diagram of Principle. Legend. A Distribution panel B Coil remote switch L1-L2-L3-N Input power source L11-L21-L31-N1 Backup power source M1 Input power terminal board M2 Backup power terminal board T1 Remote switch 1 T2 Remote switch 1 Q1 Input power switch Q2 Backup power switch XB1 Connector on BKF PCB XB2 Co

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 36 ITALIANOENGLISH PROBLEM SOLVING 9 The alarm messages displayed enable an immediate diagnosis. Alarms are divided into two categories: • alarms related to the UPS external circuits, (input mains, output mains, temperature and environment). • alarms related to the UPS internal circuits. In this case, the corrective actions will be carried out by the After Sales Department. 9.1 SYSTEM ALARMS. • A02: output overload. The power required by the loads is higher than the power available. Check that the load is well balanced on the three phases by

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 41 ENGLISH 10 OPTIONS Intervention of the E.S.D. input switches o the UPS output. To restore the UPS to operation: • Close the E.S.D. contact on “In 1” on the ADC board. • Give the reset alarms” command. • Run the start procedure 10.1.1 ADC card installation. • Set the operating mode by means of the DIP switches 1 and 2 • If the external ESD contact is not used, check that there is a jumper between pins IN1+ and IN1-. If there is no jumper, the UPS cannot be started when the card is inserted in the sl

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 43 ENGLISH 10 OPTIONS 10.5 SEPARATE AUXILIARY POWER SUPPLY. This allows the use of an auxiliary energy source other than the primary mains power supply in the event of outage. 10.6 EXTERNAL BACK-FEED PROTECTION. The UPS systems are designed for the installation of an external device that protects against the back-feed of dangerous voltages on the power line, or if it is a separate line, on the auxiliary back up power supply line. The BKF card shown in gure 10.6.1 is used to control the external device. The BKF PCB is installed in the position shown in g 10.6.2. Ref

  • MASTERYS BC from 15 to 20 kVA 35 ENGLISH 8 COMMUNICATION T.SERVICE This is a cutting edge supervision service ensuring 24 x 7 service. It ensures eective prevention and constant monitoring of the system. Communication between the UPS and the local technical support centre is via Internet with the help of NetVision (via the mail-server on the same network). Any emergency situation

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 46 ITALIANOENGLISH TECHNICAL SPECIFICATIONS 11 Models 15 15 20 20 Input/Output phases 3/1 3/3 3/1 3/3 Standards 15 15 20 20 Safety (EN) IEC 62040-1-1, (EN) IEC 60950-1-1* Type and performance (EN) IEC 62040-3 (VFI-SS-111) EMC IEC 62040-2, EN 50091-2 Product certication Protection level IP20 (compliant with 60529), IP21 on request *TÜV tested Environment 15 15 20 20 Operating temperature 0÷40 °C (15÷25 °C recommended for longer battery life) Stora

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 15 ENGLISH 3 UNPACKING AND INSTALLATION OF THE UNIT 3.5-9 Connect the external battery cables (if present) to the terminals labelled “EXTERNAL BATTERY” +B2, -B2, -B1, +B1 (refer to paragraph 3.10); connect the Power Share cables to the terminals labelled “POW- ER SHARE” L15, L25, L35, N5 (the option is available). 3.5-10 Divert any control cables from the front (RS232, signalling relay contacts, etc.) into the appropriate side cable run A. 3.5-11 Remove the pre-cut detail C and bend details B to p

  • MASTERYS BC from 15 to 20 kVA 22 ITALIANOENGLISH 5 ACCESS TO CONTROLS AND COMMUNICATION INTERFACES This chapter identies the electromechanical switches, described below, and used for start-up, shutdown and maintenance bypass procedures. Access to the control area is from the front by opening the upper door using the red handle as shown in gure 5-1. The

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 21 ENGLISH MODES OF OPERATION 4 4.5 OPERATION IN GE CONFIGURATION. MASTERYS™ can be operated in conjunction with a generator (GE). With a generator, the frequency and voltage ranges of the auxiliary mains can be increased to accept the in- stability of the GE and at the same time to avoid operation from the battery or risks of out-of-synchronisation switching onto the bypass.

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 3 ENGLISH INDEX 1. CERTIFICATE AND CONDITIONS OF WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.1 Important. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.2 Description of the symbo

  • MASTERYS BC from 15 to 20 kVA 25 ENGLISH 6 MIMIC PANEL 6.1.1-1 6.1.1 Meaning of LEDs. LED L1 - GREEN: • On: Rectier and Battery charger on • Flashing: Rectier alarm • O: No input mains present LED L2 - YELLOW: • On: Operation from battery - battery test • Flashing: Battery section alarm • O: Battery charged LED L3 - GREEN: • On: Inverter on

  • socomec Masterys BC, MASTERYS BC from 15 to 20 kVA 7 ENGLISH The product you have chosen is designed for commercial and industrial use only. In order to be used for particular “critical applications” such as life support systems, medical applications, com- mercial transportation, nuclear facilities or any other application or systems where product failure is likely to cause substantial harms to person or property, the products may have to be adapted. For such uses we would advise you to contact SOCOMEC UPS beforehand to conrm the ability of these prod- ucts to meet the requested level of safety, performance, reliability and compliance with applicable laws, regula- tions and

Related Products and Documents (UPS):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 NAPCO Gemini GEM-P3200 Installation instructions manual napco/gemini-gem-p3200-E72.pdf 07 Jul 2022 64
2 Weed Eater 545154699 Instruction manual weed-eater/545154699-IOV.pdf 30 Jan 2024 12 0.21 Mb
3 Sennheiser Set SET 820 Technical data sennheiser/set-set-820-2GP.pdf 06 Apr 2023 1 0.09 Mb
4 Elmo P100 Instruction manual elmo/p100-23G.pdf 31 Aug 2023 48 4.46 Mb
5 HAI OmniTouch 10p Operation & user’s manual hai/omnitouch-10p-9G6.pdf 02 Dec 2022 44 3.22 Mb
6 Philips Resettable SPP7354WA Specifications philips/resettable-spp7354wa-261.pdf 14 Nov 2022 2 0.37 Mb

Similar Resources:

  • Airpax Dimensions

    ADI-24/2400N

    (8 pages)
    Airpax Dimensions, Inc.U.P.S.Unintertuptable Power Supply(External Battery Type)OWNERS MANUAL for Models:ADI-24/2400N UPSADI-24/4800N UPSIncluding Option "D"Form 121585 121585B OWNER'S MANUAL FEBRUARY 2007 Airpax Dimensions, Inc. 4467 White Bear Parkway (651) 653-7000 S …
  • Ablerex

    ARES RT-1K

    (22 pages)
    1 Intelligent True On-Line UPS For Corporate and IT Users User Manual Table of Contents 1. Safety and Storage Instructions .............................................................2 1.1 Safety ........................................................................................................2 1.2 Storage ... …
  • ATEN

    NRGence OL1000 Series

    (73 pages)
    Professional Online UPSOL1000HV / OL1000SHV / OL1500HV / OL2000HV / OL2000SHV / OL3000HV / OL1000LV / OL1000SLV / OL1500LV / OL2000LV / OL2000SLV / OL3000LVUser Manualwww.aten.comATEN NRGence™OL1000 / OL1500 /OL2000 / OL3000 SeriesProfessional Online UPSUser Manual …
  • Toshiba

    G9000 SERIES

    (78 pages)
    UNINTERRUPTIBLE POWER SYSTEM (UPS) G9000 SERIES G9000 ENHANCED SERIES UPS INSTALLATION AND OPERATION MANUAL 480/480 V 100/160/225 kVA Doc. No.: 93823-004 Reference: 4GBH0094 Rev. E December 2015 …
  • OPTI-UPS

    DS1000B

    (2 pages)
    DS1000B / DS1500B / DS2000B / DS3000B* DS1000B30.Online Double Conversion UPS TechnologyFeaturesBackup Time (Typical)1PC+1LCD 80 mins 1PC+1LCD 90 mins DS1000BDS1500B* Zero transfer time (online)* Smart fan speed control* Saves more power and minimizes noise* 4 hours recharge time* Cold start (DC power on)* EPO port ready: emergency power off switch* …
  • Liebert

    Hinet 10kVA

    (43 pages)
    Manual Reference number : 6390001 H - 2 (12/01) Rev ENP Au 07/2002 HHIINNEETT UUPPSS SSYYSSTTEEMM 1100 –– 3300 kkVVAA 33xx11 UUsseerr MMaannuuaall …

Comments, Questions and Opinions: