Manualios.com

Speed Queen Stacked Washers and Dryers Installation Instructions Manual

  • Stacked Washers and Dryers Washer
  • maQ9uJBSsExYg
  • Installation Instructions Manual
  • PDF / Adobe Acrobat Reader
  • 26

Speed Queen Stacked Washers and Dryers Manual Online:

4.5, 2343 votes
Speed Queen Stacked Washers and Dryers User Manual
Speed Queen Stacked Washers and Dryers User Guide
Speed Queen Stacked Washers and Dryers Online Manual

Text of Speed Queen Stacked Washers and Dryers User Guide:

  • Speed Queen Stacked Washers and Dryers, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 7 802714R5 Place a level on the cabinet top and check if the unit is level from side to side and front to back. NOTE: Level must rest on raised portion of top panel. Refer to Figure 3. If unit is not level, tilt unit to access the front and rear leveling legs. For easier access to leveling legs, prop up unit with a wooden block. Refer to Figure 4. Loosen the locknuts and adjust legs by screwing into or out of unit base. Make sure that the unit does not rock. When unit

  • Speed Queen Stacked Washers and Dryers, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 5 802714R5 Reassembly 1. Lift dryer and place it on top of washer so dryer leveling legs sit in notches in control cabinet. 2. Slide dryer backward until mounting holes in base line up with holes in front of security cabinet. 3. Replace two 7/16 inch screws and washers holding dryer to washer. 4. Reconnect dryer wire harness. If needed, refer to unit’s wiring diagram. 5. Reattach the control panel to the control cabinet using four screws. 6. Replace dryer’s front access panel. Installation Step 1: Posi

  • Speed Queen Stacked Washers and Dryers, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802714R5 10 Step 4: Connect Drain Hose to Drain Receptacle Remove the drain hose from its shipping position on the rear of the washer by unhooking the hose from the retainer clamp and by removing the shipping tape. Install the drain hose into the drain receptacle (standpipe, wall or laundry tub) following the instructions below. IMPORTANT: Drain receptacle must be capable of handling a minimum of 1-1/4 inch (32 cm) outside diameter drain hose. Standpipe Installation: Place the drain hose into the standpipe. Remove the beaded strap from accessories bag and p

  • Speed Queen Stacked Washers and Dryers, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 17 802714R5 Step 7: Connect Dryer Exhaust System • DO NOT use plastic, thin foil or type B ducting. Rigid metal duct is recommended. Refer to Figure 21. • Locate dryer so exhaust duct is as short as possible. • Be certain old ducts are cleaned before installing your new dryer. • Use 4 inch (102 mm) diameter rigid or flexible metal duct. • The male end of each section of duct must point away from the dryer. • Use as few elbows as possible. • Use of duct tape or pop-rivets on all seams and joints is recommended, if allowed by local codes. DO NOT use sheet metal screws or

  • © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 3 802714R5 Dimensions SWD895N * With leveling legs turned into base. NOTE: Exhaust openings are 4 in. (10.2 cm) metal ducting. SWD895N 23.5 in. (59.7 cm) 28 in. (71.1 cm) *75.25 in. (191 .1 cm) 26.875 in. (68.3 cm) 8.0 in. (20.3 cm) 15.4 in. (39.1 cm) 5.25 in. (13.3 cm) *44.1 in. (112 cm) 2.0 in.

  • Speed Queen Stacked Washers and Dryers, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802714R5 12 8. Remove the shipping cap from the gas connection at the rear of the dryer. Make sure you do not damage the pipe threads when removing the cap. 9. Connect to gas supply pipe. NOTE: When connecting to a gas line, an equipment shut-off valve must be installed within 6 feet (1.8 m) of the dryer. An 1/8 in. NPT pipe plug must be installed as shown for checking inlet pressure. Refer to Figure 11. 10. Tighten all connections securely. Turn on gas and check all pipe connections (internal & external) for gas leaks with a non-corrosive leak detection

  • Speed Queen Stacked Washers and Dryers, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802714R5 8 Step 3: Connect Fill Hoses Water Supply Water supply faucets must fit standard 3/4 inch (19.1 mm) female garden hose couplings. DO NOT USE SLIP-ON OR CLAMP-ON CONNECTIONS. Water supply faucets should be readily accessible to permit turning them off when washer is not being used. Recommended cold water temperature is 60 o to 80 o Fahrenheit (16 o to 27 o Celsius). Recommended maximum hot water temperature is 125 o Fahrenheit (51 o Celsius). Warm water is a mixture of hot and cold water. Warm water t

  • Speed Queen Stacked Washers and Dryers, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802714R5 4 Before You Start Supplies For most installations, the basic supplies you will need are: Figure 1 Parts Included An accessories bag has been shipped inside your unit. It includes: • Installation Instructions • Two User’s Guide (one for washer and one for dryer) • Warranty Bond • Three screws (electric dryers only). Refer to Connecting Power Cord sections in Step 5 of Installation. • Two fill hoses with washers and filter screens. Refer to Step 2 of Installation. • Four rubber feet. Refer to Step 7 of Installation. • Beaded strap. Refer to Step 3 of Installation. NOTE: If the unit is delive

  • Speed Queen Stacked Washers and Dryers, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 13 802714R5 Step 6: (Electric Dryer Only) Connect Electrical Plug Dryer requires 120/240 Volt or 120/208 Volt, 60 Hertz, 3 or 4 wire electrical supply. Refer to serial plate for specific electrical requirements. NOTE: The wiring diagram is located behind the control panel, inside the control cabinet. Grounding Information • This dryer must be connected to a grounded metal, permanent wiring system; or an equipment-grounding conductor must be run

  • Speed Queen Stacked Washers and Dryers, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802714R5 20 Step 9: Wipe Out Inside of Washer Drum and Dryer Drum Before using the washer and dryer for the first time, use an all-purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside the drums. Step 10: Plug In the Washer and Dryer Electric Dryer Connect the dryer to an electrical power source. Refer to Step 4 for information on connecting power cord. Figure 29 Gas Dryer Dryer requires 120 Volt, 60 Hertz electrical supply and comes equipped with a 3-prong

  • Speed Queen Stacked Washers and Dryers, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9 802714R5 IMPORTANT: Hoses and other natural rubber parts deteriorate after extended use. Hoses may develop cracks, blisters or material wear from the temperature and constant high pressure they are subject to. All hoses should be checked on a monthly basis for any visible signs of deterioration. Any hose showing the signs of deterioration listed above should be replaced immediately. All hoses should be replaced every five years. IMPORTANT: Turn off water supply faucets after check-out and demonstration. Owner should turn off water supply whenever there will be an extended period of non-use. NOTE:

  • Speed Queen Stacked Washers and Dryers, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 15 802714R5 4. Use the three screws from the accessories bag to attach the power cord wires to the terminal block. Refer to Figure 15. Figure 15 5. Tighten all screws firmly. IMPORTANT: Failure to tighten these screws firmly may result in wire failure at the terminal block. 6. Secure the strain relief to the power cord, or wires, where they enter the dryer cabinet. 7. Check the continuity of the ground connection before plugging the cord into an outlet. Use an acceptable indicating device connected to the center grounding pin of the plug and the green screw on the back of the cabin

  • Speed Queen Stacked Washers and Dryers, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 11 802714R5 Laundry Tub Installation: For this type of installation, the drain hose MUST be secured to the stationary tub to prevent hose from dislodging during use. Refer to Figure 10. Use the beaded strap (supplied in accessories bag) to secure hose. Step 5: (Gas Dryer Only) Connect Gas Supply Pipe 7. Make certain your dryer is equipped for use with the type of gas in your laundry room. Dryer is equipped at the factory for Natural Gas with a 3/8 inch NPT gas connection. NOTE: The gas service to a gas dryer must conform with the local codes and ordinances, or in the abs

  • Speed Queen Stacked Washers and Dryers, Keep these instructions for future reference. (If this machine changes ownership, this manual must accompany machine.) www.speedqueen.com Dimensions........................................................................ 3 Before You Start................................................................ 4 Installation......................................................................... 5 Installer Checklist ........................................... Back Cover Date Purchased _____________________________ Model Number _____________________________ Serial Numb

  • Speed Queen Stacked Washers and Dryers, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802714R5 14 Connecting Power Cord with Three-Wire Plug NOTE: Four-wire cord is required for mobile homes or where codes do not permit grounding through neutral. Figure 12 1. Disconnect power to dryer. 2. Remove access cover from rear of dryer. Figure 13 3. Use a strain relief and insert end of power cord through power supply hole. Figure 14 D816I 1 3 Wire Grounded Neutral 120/240 Volt, 60 Hertz AC 1 Phase Service Entrance Switch Box (Refer to NOTE above) 4 Metallic or Non-Metallic Sheathed Cable (Copper Wire Only) 5 Power Cor

  • © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802714R5 16 3. Remove ground screw from ground to neutral wire and save for use in Step 5. Ground to neutral wire will be attached to the neutral terminal in Step 6. Figure 18 4. Use a strain relief and insert end of power cord through power supply hole. Figure 19 5. Attach power cord ground (g

  • Speed Queen Stacked Washers and Dryers, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802714R5 6 Step 2: Position and Level the Unit Position unit so it has sufficient clearance for installation and servicing. Refer to Figure 2. Figure 2 NOTE: Use of the dispenser drawer or unit doors as a handle in the transportation of the unit may cause damage to the dispenser or doors. Place unit in position on a solid, sturdy and level floor. Installing the unit on any type of carpeting, soft tile, a platform or other weakly s

  • © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 23 802714R5 Grounding Information The washer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. The washer is equipped with a cord having an equipment-grounding conductor and a 3-prong ground

  • Speed Queen Stacked Washers and Dryers, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installer Checklist Fast Track for Installing the Unit (Refer to the manual for more detailed information) • Position Unit Near Installation Area. 1 CHECK • Position and Level the Unit. 2 CHECK SWD833N SWD833N • Connect Fill Hoses. FLW2054N COLD HOT 3 FLW2054N Filter Screens Cold Valve Connection Plain Washers Red Blue CHECK Hot Valve Connection • Connect Drain Hose to Drain Receptacle. 4 SWD598N SWD598N CHECK • Connect Gas Supply Pipe. • Check for Gas Leaks. 5 Gas Only CHECK D434I • Connect Electrical Cords. 6 D679IE0A CHECK D679

  • Speed Queen Stacked Washers and Dryers, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802714R5 2 The following information applies to the state of Massachusetts, USA. • This appliance can only be installed by a Massachusetts licensed plumber or gas fitter. • This appliance must be installed with a 36 inch (91 cm) long flexible gas connector. • A “T-Handle” type gas shut-off valve must be installed in the gas supply line to this appliance. • This appliance must not be installed in a bedroom or bathroom. • Do not store or use gas

Related Products and Documents (Washer):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Samsung GT-S5511T Operation & user’s manual samsung/gt-s5511t-X51.pdf 21 Dec 2023 77 0.82 Mb
2 Samsung 320MXn-2 - SyncMaster - 32" LCD Flat Panel Display Guía de inicio rápido samsung/320mxn-2-syncmaster-32-lcd-flat-panel-display-HK1.pdf 09 Aug 2022 28 1.36 Mb
3 Bryant HRVBBLHU User's information manual bryant/hrvbblhu-C9F.pdf 30 Jan 2024 2 0.03 Mb
4 Whirlpool WVE16402 W Main features whirlpool/wve16402-w-4L1.pdf 23 Jan 2023 1 0.4 Mb
5 Electrolux 775302 Specifications electrolux/775302-C2P.pdf 16 Dec 2022 2 0.27 Mb
6 WELLTECH FXSO GATEWAY H.323 3701A - VERSION 1.0 Manual  welltech/fxso-gateway-h-323-3701a-version-1-0-F89.pdf 25 Feb 2024 91 3.73 Mb

Similar Resources:

  • Karcher

    K 3.67 M

    (52 pages)
    English 2Français 18Español 35K 3.49 M 59629130 06/09HIGH PRESSURE WASHER - OPERATOR MANUALNETTOYEUR HAUTE PRESSION - MANUEL D'UTILISATIONMANUAL DE USUARIO DEL LIMPIADOR DE ALTA PRESIÓN …
  • Miele

    PW 6241 EL

    (102 pages)
    PW 6241 EL/RHde Installationsplan Gewerbliche Waschmaschineen Installation plan Commercial washing machinefr Schéma d’installation Lave-linge professionnelses Plano de instalación Lavadora industrialru Монтажный план Профессиональная стиральная машинаit Schema di installazione Lavatrice a uso professionaleM.-N …
  • Whirlpool

    WVFC750AJGR

    (9 pages)
    SPECIFICIONS � …
  • Haier

    HWM65-187S

    (17 pages)
    Twin-tub washing machineModel HWM65-187SSERVICE MANUALManual code:SM HWM65-187SEdition: 2008.04.17FeaturesFull plastic cabinetChoose water current and washing timeChoose spinning timeSperate washing and spinningFull plastic washing tub and spinning tub …
  • Miele

    W3039i

    (60 pages)
    Operating and InstallationInstructionsWasherW 3039To prevent accidents andmachine damage,read these instructionsbefore installation or use.M.-Nr. 06 911 022en-US …
  • Indesit

    IWD 5105

    (84 pages)
    GB1ContentsInstallation, 2-3Unpacking and levellingConnecting the electricity and water suppliesThe first wash cycleTechnical dataCare and maintenance, 4Cutting off the water or electricity supplyCleaning the washing machineCleaning the detergent dispenser drawerCaring for the door and drum of your applianceCleaning the pumpChecking the water inlet hosePreca …

Comments, Questions and Opinions: