Manualios.com

Pioneer YN018-2 Operation & User’s Manual

Pioneer YN018-2 Manual Online:

3.45, 1278 votes
Pioneer YN018-2 User Manual
Pioneer YN018-2 User Guide
Pioneer YN018-2 Online Manual

Text of Pioneer YN018-2 User Guide:

  • Pioneer YN018-2, Before using your air conditioner, please read this manual carefully and keep it for future reference. INVERTER DUAL (2), TRIPLE (3) and QUAD (4) Zone MULTI SPLIT SYSTEM HEAT PUMP Models: YN018-2, 027-3, 030-3, 036-4, with WB: Wall, CB: Cassette, RB: Concealed-Duct, UB: Floor-Ceiling, FB: Floor Console Indoor Units Read This Manual Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventative care on your part can save you a great deal of time and money over th

  • 1 CONTENTS Contact an authorised service technician for repair or maintenance of this unit. Contact the installer for installation of this unit. The air conditioner is not intended for use by young children or invalids without supervision. Young children should be supervised to ensure that they do not play with the air conditioner. If the power cord is to be replaced, replacement work shall

  • 3 SAFETY PRECAUTIONS 3 To prevent injury to the user or other people and property damage, the following instructions must be followed. Incorrect operation due to ignoring of instructions may cause harm or damage. The seriousness is classified by the following indications. This symbol indicates the possibility of death or serious injury. Meanings of symbols used in this manual are as s

  • Pioneer YN018-2, 4 SAFETY PRECAUTIONS CAUTION When the air filter is to be removed, do not touch the metal parts of the unit. It may cause an injury. Do not clean unit when power is on as it may cause fire and electric shock, it may cause an injury. Operation with windows opened may cause wetting of indoor and soaking of household furniture. When the unit is to be cleaned, switch off, and turn off the circuit breaker. Stop operation and close the window in storm or hurricane. Use caution when unpacking and installing. Sharp edges could cause injury. Do not clean the air conditioner with water. Water may enter the unit and degrade the insulat

  • Pioneer YN018-2, OPERATING INSTRUCTIONS Indoor unit Outdoor unit Identification of parts Indoor unit Outdoor unit Air outlet One-twin One-three One-four One-five 9 10. Drain hose, refrigerant connecting pipe 11. Connective cable 12. Stop valve 13. Fan hood 10 11 12 13 Indoor unit Air outlet Air inlet 1. Panel frame 2. Rear air intake grille 3. Front panel 4. Air Purifying filter & Air filter(behind) 5. Horizontal louver 6. LCD display window 7. Vertical louver 8. Manual control button(behind) 9. Remote controller holder 8 run ion timer def. Display window NOTE: The display window on the air conditioner you purchased may look like one of the following: (1)

  • Pioneer YN018-2, AUTO operation display Displayed during Auto operation. OPERATION display Displayed when the air conditioner is in operation. DEFROST operation display (For Heating & Cooling model only): Displayed when the air conditioner starts defrosting automatically or when the warm air control feature is activated in heating operation. TIMER display Displayed during Timer operation. CLEAN AIR display(optional) Displayed when CLEAN AIR feature is activated. TURBO operation display Displayed when select TURBO

  • Pioneer YN018-2, OPERATING INSTRUCTIONS 12 Display panel Identification of parts Indoor unit DISPLAY PANEL: FloorConsolte Type 1 5 6 2 4 1 3 10 7 8 9 Indoor unit Outdoor unit 7. Drain hose, refrigerant connecting pipe 8. Connective cable 9. Stop valve 10. Fan hood 1. Air flow louver (at air outlet) 2. Air inlet(with air filter in it) 3. Remote controller 4. Installation part 5. Display panel 6. Connecting pipe OPERATION indication lamp This indicator illuminates when the unit is operational. TIMER indication lamp Lights up during Timer operation.

  • Pioneer YN018-2, OPERATING INSTRUCTIONS 13 Display panel Identification of parts Indoor unit DISPLAY PANEL: Floor and standing type(console) 7 Indoor unit Outdoor unit 8. Drain hose, refrigerant connecting pipe 9. Connective cable 10. Stop valve 11. Fan hood 1. Indoor unit 2. Air flow louver (at air outlet) 3. Installation part 4. Air out 5. Air inlet(with air filter in it) 6. Air in 7. Remote controller OPERATION indication lamp This indicator illuminates when the unit is operational. TIMER indication lamp Lights up during Timer operation. AlARM indication la

  • Pioneer YN018-2, OPERATING INSTRUCTIONS 14 4 4 2 2 5 5 1 1 3 3 Infrared signal receiver Infrared signal receiver Infrared signal receiver Infrared signal receiver (2) (3) (4) (5) 4 2 5 1 36 5 1 2 3 4 6 MANUAL OPERATIONOPERATION TIMER DEF./FAN ALARM Temporary button This button is used to operate the unit temporarily in case you misplace the remote controller or its batteries are exhausted. One press of the manual control button will lead to the forced AUTO operation. If press the button twice within five seconds, the unit will operate under forced COOL operation. The forced COOL operation is used for testing purposes only, please do

  • Pioneer YN018-2, OPERATING INSTRUCTIONS 15 Display panel Identification of parts Indoor unit DISPLAY PANEL: Ceiling Concealed (Duct) type Indoor unit Outdoor unit 7. Drain hose, refrigerant connecting pipe 8. Connective cable 9. Stop valve 10. Fan hood 1. Air outlet 2. Air inlet 3. Air filter 4. Electric control cabinet 5. Wire controller 6. Drain pipe OPERATION indication lamp This indicator illuminates when the unit is operational. TIMER indication lamp Lights up during Timer operation. AlARM indication lamp Flashes when malfunction occurs. DEF./FAN indication lamp Lights up when the air conditioner starts defrosting automatically in heating operation (applicable to cooling & heating mo

  • Pioneer YN018-2, OPERATING INSTRUCTIONS 16 Display panel Identification of parts Indoor unit DISPLAY PANEL: Duct type Indoor unit Outdoor unit 5. Drain hose, refrigerant connecting pipe 6. Connective cable 7. Stop valve 8. Fan hood 1. Air outlet 2. Air inlet 3. Air filter 4. Remote controller OPERATION lamp This indicator illuminates when the unit is operational. TIMER indication lamp Lights up during Timer operation. AlARM indication lamp Flashes when malfunction occurs. PRE-DEF./FAN indication lamp Lights up when the air conditioner starts defrosting automatically in heating operation (applicable to cooling & heating models only) or fan only mode

  • Pioneer YN018-2, Identification of parts Indoor unit Compact four-way cassette type OPERATING INSTRUCTIONS 1 2 3 4 5 6 7 8 9 10 11 11 12 Indoor unit Outdoor unit 11. Air inlet 12. Air outlet 1. Air flow louver(at air outlet) 2. Drain pump(drain water from indoor unit) 3. Drain pipe 4. Air outlet 5. Air filter(inside air-in grill) 6. Air inlet 7. Air-in grill 8. Display panel 9. Remote controller 10. Refrigerant pipe Display panel DISPLAY PANEL: OPERATION lamp This indicator illuminates when the unit is operational. TIMER indication lamp Lights up during Timer operation

  • Pioneer YN018-2, 18 Manul operation can be used temporarily in case you can not find the remote controller or test running purpose or maintenance necessary. OPERATING INSTRUCTIONS Manual operation NOTE: This manual does not include Remote Controller Operations, see the <<Remote Controller Instruction>> packed with the unit for details. Operating temperature Manual control button AUTO/COOL Model A Model B Manual control button For DUCT and CEILING type, CASSETTE type, CEILING and FLOOR type and FLOOR and STANDING type, please refer to the previous pages to operate the Man

  • Pioneer YN018-2, 19 OPERATING INSTRUCTIONS Airflow direction control Do not operate the air conditioner for long periods with the air flow direction set downward in cooling or dehumidifying mode. Otherwise, condensation may occur on the surface of the horizontal louver causing moisture to drop on to the floor or on furnishings. Do not move the horizontal louver manually unless it is necessary. Always use the remote controller. When the air conditioner is started immediately after it was stopped, the horizontal louver might not move for approximately 10 seconds. Open angle of the horizontal louver should not be set too small, as COOLING or HEAT

  • Pioneer YN018-2, 20 OPERATING INSTRUCTIONS The following is how to adjust the air flow direction when the air outlet parts (sold separately) is used with the indoor unit. Heating To effectively heat the bottom of the room please set the louver downwards. Cooling To effectively cool the whole room, please adjust the louver horizontally. Duct-Ceiling Type Auto-swing Press SWING button, the louver will swing up and down(left and right) automatically. Manual Swing Adjust the louver to achieve better cooling/ heating effects when cooling/heating. When cooling Adjust the louver horizontally. When heating Adjust the louver downwards (vert

  • Pioneer YN018-2, 21 AUTO operation SLEEP operation DRYING operation When you set the air conditioner in AUTO mode, it will automatically select cooling, heating(cooling /heating models only), or fan only operation depending on what temperature you have selected and the room temperature. The air conditioner will control room temperature automatically round the temperature point set by you. If the AUTO mode is uncomfortable, you can select desired conditions manually. When you push SLEEP button on remote controller during cooling, heating(cooling only type without), or AUTO operation , the air conditioner will automatically increase (cooling) or decrease (heating) 1 (2 F) per hour. The set

  • Pioneer YN018-2, While simultaneously operating two indoor units or more, make sure the operation modes will not conflict with each other. The heat mode claims precedence over all other modes. For example: If the unit intially started operates under cool(or fan) mode, the other units can operate under any mode except heat. If one of the unit selects heat mode, the other operating units will stop operation and diplay P5 (For the units with display window only) or the Auto and Operation indication light flash rapidly, the Defrost indication light turn off, the Timer indication light remain on(For the units without

  • Pioneer YN018-2, 23 CARE AND MAINTENANCE Cleaning the Grille, Case and Remote Controller A cloth dampened with cold water may be used on the indoor unit if it is very dirty. Then wipe it with a dry cloth. Do not use a chemically treated cloth or duster to clean the unit. Do not use benzine, thinner, polishing powder, or similar solvents for cleaning. These may cause the plastic surface to crack or deform. Never use water hotter than 40 C(104 F) to clean the front panel, it could cause deformation of discoloration. o CAUTIONS Care and maintenance Turn the system off before cleaning. To cl

  • Pioneer YN018-2, 24 CARE AND MAINTENANCE Maintenance Checks before operation If you plan to idle the unit for a long time, perform the following: (1) Operate the fan for about half a day to dry the inside of the unit. (2) Stop the air conditioner and disconnect power. (3) The outdoor unit requires periodic maintenance and cleaning. Do not attempt to do this yourself. Contact your dealer or servicer. Remove the batteries from the remote controller. Check that the wiring is not broken off or disconnected. Check that the air filter is installed. Check if the air outlet or inlet is blocked after the air conditioner has not been use

  • 25 CARE AND MAINTENANCE CASSETTE TYPE 2. Take out the air-in grill (together with the air filter shown in Fig. B). Pull the air-in grill down at 45 and lift it up to take out the grill. 3. Dismantle the air filter 4. Clean the air filter(Vacuum cleaner or pure water may be used to clean the air filter. If the dust accumulation is too heavy , please use soft brush and

  • 26 CARE AND MAINTENANCE Air Inlet Air Filter CEILING AND FLOOR TYPE FLOOR AND STANDING TYPE(Console) For <36000Btu/h models 1. Open the air intake (see Fig.E1). 2. Take out the air filter(see Fig.E2). 3. Clean the air cleaning filter with water or vacuum cleaner, then dry it in cool place. 4. Re-install the air filter in the reverse order of Fig.E2. 1. Open the front panel.(Refer t

  • Pioneer YN018-2, 27 CARE AND MAINTENANCE 2. Remove the air filter Press the claws on the right and left of the air filter down slightly, then pull upward.(Refer to Fig.F2) 3. Take off the especial function filter 4. Clean the air filter 5. Set the air filter and the especial function filter as they were and close the front panel. CAUTION: Do not dry the air filter by heat or under the direct sunlight. Hold the tabs of the frame, and remove the claws in 4 places. (Refer to Fig. F3) (The expecial function filter can be renewed by washing it with water once every 6 months. We recommend replacing it once

  • 28 CARE AND MAINTENANCE Fig.G1 Fig.G2 Fig.G3 Fig.G4 DUCT /CEILING TYPE 1. For the unit is a rear ventilated one, please remove the screws (2 pieces) fixed on the filter and take down the filter away from the unit. See Fig.G1. 2. For the unit is a descensional ventilated one, please push the filter up slightly to let the position retainer escape away from the flange fixed holes, and tak

  • Pioneer YN018-2, Maintenance If you plan to idle the unit for a long time, perform the following: Use a dry cloth to wipe off the dust accumulated on rear air intake grille, in order to avoid the dust blowing out from the indoor unit. Check that the wiring is not broken off or disconnected. Check that the air filter is installed. Check if the air outlet or inlet is blocked after the air conditioner has not been used for a long time. 1. Clean the indoor unit and air filter. 2. Select FAN only mode, let the indoor fan run for a while to dry the inside of the unit. 3. Disconnect the power supply and remove battery from the remote control. 4. Check components of the outdoor unit periodically

  • Pioneer YN018-2, 11 4. This is a normal condition when the air conditioner has not been used for a long time or during first use of the unit. 5. This is caused by the indoor unit giving off smells permeated from building material, from furniture, or smoke. Dust is blown out from the indoor unit. A peculiar smell comes out from the indoor unit. 6. When indoor temperature reaches the temperature setting on air conditioner, the compressor will stop automatically, and the air conditioner turns to FAN only mode. The compressor will start again when the indoor temperature rises on COOL mode or falls on HEAT mode (For cooling and heating models only) to the

  • Pioneer YN018-2, 31 TROUBLESHOOTING TIPS Stop the air conditioner immediately if one of the following faults occur. Disconnect the power and contact the nearest customer service center. Fuse blows frequently or circuit breaker trips frequently. Other objects or water penetrate the air conditioner. The remote controller won't work or works abnormally. Other abnormal situations. Trouble Malfunctions Unit does not start Unit not cooling or heating (Cooling/ heating models only) room very well while air flowing out from the air cond tioneri Cause Power cut Unit may have become unplugged. Fuse may have blown.

Related Products and Documents (Heat Pump):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Graco 309092F Instruction manual graco/309092f-NG9.pdf 16 Sep 2022 12 0.41 Mb
2 Sennheiser E835 User manual manual sennheiser/e835-Y25.pdf 11 Jul 2022 12 0.43 Mb
3 Philips DECT5112L Specifications philips/dect5112l-B39.pdf 05 Jan 2023 3 0.49 Mb
4 GE 2-9868 Operation & user’s manual ge/2-9868-KS3.pdf 17 Nov 2022 20 0.6 Mb
5 Leviton 5249 Installation instructions manual leviton/5249-3X6.pdf 19 Nov 2023 3
6 Code Electronic A24 Operation & user’s manual code-electronic/a24-162.pdf 15 Jul 2022 11

Similar Resources:

  • Pioneer

    YN018-2

    (27 pages)
    Before using your air conditioner, please readthis manual carefully and keep it for future reference.INVERTER DUAL (2), TRIPLE (3) and QUAD (4) ZoneMULTI SPLIT SYSTEM HEAT PUMPModels: YN018-2, 027-3, 030-3, 036-4, withWB: Wall, CB: Cassette, RB: Concealed-Duct, UB: Floor-Ceiling, FB: Floor Console Indoor UnitsRead This ManualInside you will find many helpful …
  • Dimplex

    SI 130TUR+

    (68 pages)
    Montage- und GebrauchsanweisungDeutschEnglishFrançaisInstructions d’installation et d’utilisationInstallation andOperating InstructionsReversibleSole/Wasser-Wärmepumpe für InnenaufstellungSI 130TUR+ReversibleBrine-to-Water Heat Pump for Indoor InstallationPompe à chaleur eau glycolée-eau réversible pour installation intérieureBestell-Nr. / Order n …
  • Mitsubishi Electric

    EHSD-MEC

    (42 pages)
    РУКОВОДСТВО ПО УСТАНОВКЕДля безопасного и правильного использования внимательно прочитайте данное руководство и руководство по установке наружного блока перед установкой гидромодуля. Оригина� …
  • GE

    AZ61H12DAB

    (32 pages)
    Safety Instructions . . . . . . . . . . .2, 3Operating InstructionsAbout the Controls on the Dehumidifier . . . . . . . . . . . .4Automatic Defrost . . . . . . . . . . . . . . .5Choosing a Location . . . . . . . . . . . . .5How the Dehumidifier Operates . . .5Removing Collected Water . . . . . .6Water Level . . . . . . . . . . . . . . . . . . . .6Care …
  • Trane

    Axiom EXHF006

    (84 pages)
    SSAAFFEETTYY WWAARRNNIINNGGOnly qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, and air-conditioningequipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or altered equipment by an unqualified personcould result in death or se …
  • Viessmann

    VITOCAL 200-S AWS

    (64 pages)
    VIESMANNVITOCAL 200-SAir/water heat pump, split version3.0 to 10.6 kWVITOCAL 200-S Type AWSHeat pump with electric drive in split design with external andinternal unit.For central heating and DHW heating in heating systems.■Internal unit with heat pump control unit Vitotronic 200, cir-culation pump for the heating circuit, 3-way diverter valve,expansion …

Comments, Questions and Opinions: