E-FLITE Mini Ultra Stick Assembly Manual

Text of E-FLITE Mini Ultra Stick User Guide:

• E-FLITE Mini Ultra Stick, GENERAL 1) I will not fly my model aircraft in sanctioned events, air shows or model flying demonstrations until it has been proven to be airworthy by having been previously, successfully flight tested. 2) I will not fly my model higher than approximately 400 feet within 3 miles of an airport without notifying the airport operator. I will give right-of-way and avoid flying in the proximity of full-scale aircraft. Where necessary, an observer shall be utilized to supervise flying to avoid having models fly in the proximity of full-scale aircraft. 3) Where established, I will abide by the safety rules for the flying s

• E-FLITE Mini Ultra Stick,  2. Secure the servo using the hardware that was provided with the servo.  3. Drill a 3/32" hole in the outside hole of a servo arm. Install a micro control connector in the hole, and then secure its location using a micro control connector backplate. 23

•  2. Install the battery hatch to the top of the fuselage. The magnet will hold the battery hatch in place.  3. Plug in the aileron (and flap) servo leads. Slide the wing dowels into the holes at the front. Use the two 4-40 x 3/4" socket head screws and two #4 washers to secure the wing. 30

• E-FLITE Mini Ultra Stick, Final Assembly Required Parts • Fuselage • Wing • Battery • Battery hatch • 4-40 x 3/4" socket head bolt (2) • #4 washer (2) • Hook and loop tape • Hook and loop strap Required Tools and Adhesives • Hex wrench: 3/32"  1. With the aircraft fully assembled, install the battery into the battery compartment. Secure the battery using the hook and loop tape and a hook and loop strap. Note: Place a piece of hook and loop tape on the bottom of the battery and on the fuselage where the battery rests. This will keep the battery from shifting forward or backward during extr

• E-FLITE Mini Ultra Stick, 6 High Power Setup (Using Gearbox)* EFLM1100 Park 400 Brushless Inrunner Motor, 4200Kv EFLM240 400 Gearbox, 6.5:1 0.5 Module w/2 Pinions EFLA311B 20-Amp Brushless ESC (V2) EFLP1170 11 x 7 Slow Flyer Prop EFLA270 Spinner, 1-3/4” Red (optional) or EFLA204 Micro Rubber Spinner (optional) THP21003SPL 2100mAh 3-Cell 11.1V Li-Po, 16GA or EFLB1035 11.1V 2100mAh 3-Cell Li-Po, 16GA WSD1300 Ultra Plug, Male/Female Set EFLC3005 Celectra 1-3 Cell Li-Po Charger Proper throttle management is required when using high performance setups. Using this setup with 3 cells will give you plenty of power for zippy flights. Sp

• E-FLITE Mini Ultra Stick, Outrunner Motor Installation Required Parts • Fuselage • Brushless motor • Brushless speed control • 4-40 x 1/4" socket head screw (4) • Prop adapter • Propeller Required Tools and Adhesives • Hex wrench: 3/32" Skip to page 16 for setup of an inrunner motor with gearbox. Note: This section covers the installation of a brushless outrunner motor with attachment to the outside. You do have the option of installing your outrunner inside the fuselage as well. If using our recommended E-flite™ Outrunner, it may

• E-FLITE Mini Ultra Stick,  4 Check your alignment of the wing to the horizontal stabilizer at this time. You should have some play in the stab holes. Measure the stab tip to the wing tip. Adjust the stab until the measurements are equal. Now you can tighten the 3mm locknuts at the stabilizer. Range Testing the Radio  1. Before each flying session, be sure to range check your radio. This is accomplished by turning on your transmitter with the antenna collapsed. Turn on the receiver in your airplane. With your airplane on the gro

• E-FLITE Mini Ultra Stick,  6. Slide the propeller onto the gearbox shaft. If using our E-flite™ 1 3 / 4 " spinner, next slide on a spinner backplate spacer. If you are using a rubber spinner, you will slide it on after the propeller has been secured. Note: Two spacers have been provided that are placed between the propeller and spinner backplate. Use the thin spacer for low-pitch propellers, the thick spacer for high-pitch propellers. This will prevent the blades of the propeller from contacting the spinner backplate.  7. Slide the spinner backplate onto the gearbox shaft. Secure the propeller and spinner backplate usin

• E-FLITE Mini Ultra Stick, Horizon Hobby, Inc. guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty does not cover any parts damaged by use or modification. In no case shall Horizon Hobby’s liability exceed the original cost of the purchased kit. Further, Horizon Hobby reserves the right to change or modify this warranty without notice. In that Horizon Hobby has no control over the final assembly or material used for the final assembly, no liability shall be assumed nor accepted for any damage of or caused by the final user-assembled product. By the act of using the product, the user a

• E-FLITE Mini Ultra Stick, 7 Required Tools and Adhesives Tools & Equipment EFLA250 Park Flyer Tool Assortment, 5-piece Or Purchase Separately EFLA257 Screwdriver, #0 Phillips (or included with EFLA250) EFLA255 Nut Driver, 5.5mm (or included with EFLA250) EFLA251 Hex Wrench: 3/32" (or included with EFLA250) Hobby knife Square Ruler Felt-tipped pen String Adhesives Medium CA Thick CA HAN8000 6-Minute Epoxy (option for attaching firewall) Threadlock (for mounting motor to gearbox) Optional Accessori

• E-FLITE Mini Ultra Stick,  4. Slide the gearbox into position on the motor mount. Use a 1/16" drill to drill a hole on each side of the gearbox and into the mount. Stagger the holes so the screws will not interfere with each other. Secure the gearbox using three #2 x 8mm screws. Important Information About Your Brushless ESC Make sure your ESC brake is programmed to Off. Also, be sure to use an ESC with the proper 9V cutoff when using 3-Cell Li-Po packs, or 6V cutoff when using 2-cell Li-Po packs.  5. Connect the ESC to the motor and secure the ESC

• E-FLITE Mini Ultra Stick,  2. Plug in the servos and ESC into the receiver. Mount the receiver to the side of the fuselage using hook and loop material. Route the antenna wire through the bottom of the fuselage to the rear. Note: Do not cut the antenna wire, as this will reduce the range of your radio system.  3. Install the pushrod into the elevator control horn. Secure the pushrod wire using a micro pushrod wire keeper. 27

• Option 2: Motor Installation Outside Fuselage  1. It may be necessary to attach motor mount or other accessories to your particular motor at this time.  2. Attach the Outrunner motor to the front of the firewall using four 4-40 x 1/4" socket head screws. Note: The mount is attached to the front (white side) of the firewall. Important In

• Radio Installation Required Parts • Fuselage • Receiver • Servo w/hardware (2) • Micro control connector (2) • Control connector backplate (2) • 2mm x 4mm screw (2) • Hook and loop material • Micro pushrod keeper (2) Required Tools and Adhesives • Screwdriver, #0 Phillips • Drill • Drill bit: 3/64"  1. Install the rudder and elevator servos into the fusel

• E-FLITE Mini Ultra Stick, 4 Required Radio Equipment You will need a minimum 4-channel transmitter, crystals, micro receiver, and four sub-micro servos. You can choose to purchase a complete radio system that includes all of these items or, if you are using an existing transmitter, just purchase the other required equipment separately. You may wish to install the optional quad flaps, in which case you will need a 7-channel radio and receiver on 72 MHz with mixing and six sub-micro servos. The Spektrum radio system listed below will not work for the quad �

• E-FLITE Mini Ultra Stick, Wing Preparation Required Parts • Fuselage • Wing • Control horn (2) • 6-channel receiver • Servo w/hardware (2) • 6" Y-harness • Servo extension, 3" • 4-40 x 3/4" socket head screw (2) • 3mm washer (2) • Micro control connector (2) • 2mm x 4mm screw (2) • Micro control connector backplate (2) • 5" pushrod wire (2) Required Tools and Adhesives • Thin CA • Medium CA • Ruler • Drill • Drill bit: 3/32" • Screwdriver, #0 Phillips Note: For the optional Quad Flap modification, please refer to information on Page 25.  1. Install the aileron servo into the wing. The servo lead will exit the hole in the b

• E-FLITE Mini Ultra Stick, Landing Gear Installation Required Parts • Fuselage • Landing gear assembly with wheels • 4-40 x 1/2" socket head screw (2) • #4 washer (2) Required Tools • Hex wrench: 3/32"  1. Locate the landing gear assembly. Attach the landing gear assembly to the fuselage using two 4-40 x 1/2" socket head screws and two #4 washers. Note: The landing gear will only fit one direction for the holes to line up properly. Also, check that the wheel will rotate freely. If not, loosen the nuts and retighten. 10

• E-FLITE Mini Ultra Stick, 5 The Mini Ultra Stick does not include a gearbox or propeller. However, we do include two different firewalls for attaching to the nose of the plane. You need to first determine what power system you will be using, an inrunner with a gearbox, or an outrunner. We even include a firewall stick mount, which attaches to the Stick Mount Firewall. The Outrunner Firewall can accommodate small and larger outrunners, with options of mounting your outrunner on the outside with your aluminum mount or inside of the

Related Products and Documents (Video Game Controller):

Comparable Devices:

Similar Resources:

• Sony PlayStation 4 (3 pages) SETUP INSTRUCTIONS FOR PLAYSTATION 4 1. Ensure that Circuit Breakers 2B, 3A, and 3B have been turned on in the electrical panel. 2. Turn power on for the Television, Sound bar, and the PlayStation 3. Using the television remote, select source to HDMI 1 4. Press the PS button on the controller, and then select a user.  You can use up to 4 contr …

• M.T.H. RAILKING N&W J WITHPROTO-SOUND 2.0READY-TO-RUN TRAIN SET (32 pages) RAILKING N&W J WITHPROTO-SOUND 2.0READY-TO-RUN TRAIN SETOPERATING INSTRUCTIONSYour RailKing® Ready-To-Run train set is complete with everything you need to getyour model railroad up and running. This set includes a N&W J 4-8-4 steam locomotive, a set of three passenger cars, a transformer, a loop of RealTrax, the RailKing wirelessinfrared remote co …

• Logitech G25 (2 pages) 12 13ENGLISH When fully tightened, clamp knobs can be recessed into wheel and shifter housings by pressing down and turning clockwise. To release recessed knobs for clamp adjustments, push down and turn counterclockwise. ESPAÑOL Si se atornillan completamente, los inmovilizadores pueden encajarse en alojamientos de volante y palanca, presionándolos y h …

• media-tech CORSAIR II MT1507 (10 pages) ¯ If your system doesn’t launch the installation software automatically, please  nd the auto ex-ecute  le “setup.exe”, which is located under the directory of your CD drive and click on it, then follow the on-screen instruction to install the CORSAIR II MT1507.¯ Upon completing software installation, restart your PC.Hardware Installation¯ Plug …

• HobbyZone Zig Zag Racer (24 pages) ©2002 Horizon Hobby, Inc.HobbyZone products are exclusively distributed by Horizon Hobby, Inc.4105 Fieldstone Road, Champaign, IL 61822 www.horizonhobby.com4548Zig Zag Racer manual 5/7/02 2:18 PM Page 24 …

• Blockhead Roxygen Pack BH4001 (1 pages) WARRANTY AND TECHNICAL SUPPORTEvery Blockhead branded product comes with a 90 day warranty (U.S. Only). Blockhead will replace, repair or refund any defective products or components at no charge to you within 90days of the purchase date. This warranty does not apply if the Blockhead branded product hasbeen damaged by misuse, neglect, or reasons unrelated t …

Comments, Questions and Opinions: