JR Vibe Fifty Assembly Instructions Manual

Text of JR Vibe Fifty User Guide:

• JR Vibe Fifty, * : Don’t tighten all bolts completely at this time. Flat Washer, 3mm (10 pcs) Socket Head Bolt, 3x10mm (10 pcs) 2-2 MAIN FRAME ASSEMBLY 2 11 Socket Head Bolt, 3x10mm (10pcs) Flat Washer, 3mm (10pcs) *

• JR Vibe Fifty, Item # Description Quantity 980013 SOCK ET HEAD BOLTS, 3x8mm 10 980014 SOCK ET HEAD BOLTS, 3x10mm 10 960005 STARTER HEX ADAPTOR: ALL JR 1 980004 SETSCREWS, 4x4mm 10 960157 START SHAFT BEARING BLOCK 1 980036 PL ATE WASHERS, 3mm 10 981005 BEARING, SEALED, 10x19x7mm 2 996175 GOVERNOR MOUNT 1 981025 BEARING,SEALED, 5x19x6mm 2 996181 PINION GEAR 1 996182 CLUTCH BELL ASSY w/LINING 1 961088 START SHAFT 1 996179 MAIN SHAFT 1 996180 MAIN SHAFT COLLAR 1 980115 SOCK ET HEAD BOLTS, 2.6x8mm 10 980001 SETSCREWS, 3x4mm 10 970474 AUTOROTATION

• JR Vibe Fifty, 960005 960157 996181 996182 961088 980013 980036 980004 981025 981005 980013 996175 980014 970474 961090 961074 961091 961113 961112 970513 996180 996179 980012 980065 980001 980115 980181 980164 rePlAcement PArts lIstIng 84

• JR Vibe Fifty, The following activation and setup procedure should be used for the Spektrum DX6i systems. Prior to activating the CCPM function, it is first suggested that the data reset function be performed to reset the desi red model number to be used back to the factory default settings. Caution: Prior to performing the data reset function, it will be necessary to select the desired model number to be used. A) Model Select/Data Reset Turn the power switch on then press the roll selector to enter the Adjust List. Next, move the cursor to the MODEL SEL fun ct

• JR Vibe Fifty, Start Shaft Clutch Bell Assembly Pinion Gear Start Shaft Bearing Block Setscrew, 4x4mm Complete Assembly Starter Hex Adapter d e R n e e r G n e e r G Bearing Case Direction Top Bevel Gear T20 Joint Assembly Cross Member, 28mm (3pcs) Bearing, 4x10x4mm Tail Pinion Unit B Self-Tapping Screw, 2x6mm (2pcs) Tail Pinion Shaft Assembly (Sha ft Drive) Tail Pinion Unit Bearing Case A (Bearing 4x10x4mm) Tail Pinion Unit A Complete Assembly TIP: Clean areas with rubbing alcohol to remove any oil residue

• JR Vibe Fifty, 960721 960011 970300 960722 970277 970503 996176 980022 980039 980013 980036 980036 980016 980012 980030 980037 970001 980031 996177 996178 980147 980024 980147 REPLACEMENT PARTS LISTING 82 980036

• JR Vibe Fifty, Tail Center Hub Washer, 4x7x0.5mm (2pcs) Nylon Lock Nut, 3mm (2 pcs) Flat Washer, 3mm (2pcs) Open Bearing, 4x10x3mm (2pcs) Small I.D. Large I.D. Setscrew, 4x3mm (2pcs) Bearing, 4x10x4mm (2 pcs) Washer, 7x10x1mm (2 pcs) Thrust Bearing, 4x9x4mm (2 pcs) O-ring, 3.5x5.5x1mm (2pcs) ) 2 x ( d e R Slide the tail slide ring assembly on the tail output shaft before installation of the tail rotor hub. When attaching the tail rotor hub, be certain that the setscrews (4x3mm) engage into the holes

• Setscrew, 4x4mm (4pcs) Nylon Lock Nut, 4mm A-Arm Base Spindle ) 4 x ( d e R 2-4 ELEVATOR ARM INSTALLATION 13 Setscrew, 4x4mm (4pcs) Nylon Lock Nut, 4mm (1pc) ° 0 9 Secure so that the Setscrew 4x4mm engages in the D-shape recess. Make sure that the elevator control arm is installed so that it is 90° to the A-arm base. Use the locating hole in the main frame to hel

• JR Vibe Fifty, Socket Head Bolt, 3x6mm (2pcs) Clutch Assembly Nut (Supplied with En gine) Taper Collet Upper Cooling Fan Hub Cooling Fan Blades Button Head Bolt, 3x5mm (4pcs) Taper Collet Lower Washer, 10x13x0.75 Washer (Supplied with Engine) Flat Head Screw, 2x8mm Steel Joint Ball Hex Nut, 2mm Complete Assembly YS50 only d e R ) 2 x ( d e R ) 4 x ( TIP: Before the clutch is permanently attached, rotate the clutch/fan assembly to check for trueness. If any clutch runout is detected, reposition the clutch at 90 degree intervals through the use of the four holes in

• JR Vibe Fifty, THROTTLE ARM/SERVO HORN POSITIONS To achieve the correct position of the throttle/servo arm, it may be necessary to re-position the throttle arm on the carburetor. It may also be necessary to adjust the length of the throttle linkage slightly to achieve full open and closed positions of the carburetor. It is also possible to increase/reduce the travel of the throttle servo through the travel adjust function found in most computer radio systems. If this function is used, make sure the values for the high and low positions remain equal (same value for high/low)

• JR Vibe Fifty, 120/140 3-SERVO CCPM SWASHPLATE MIXING The JR® 120°/140° CCPM or Cyclic/Collective Pitch Mixing system offers the user a control system that can accomplish the same control inputs as a one servo standard system, but with increased precision and reduced complexity. As with the one servo system, the JR CCPM system utilizes three servos for the three main controls: aileron (roll), elevator(pitch), and collective. The CCPM lower swashplate ring is designed with only three control balls, spaced at 120° or 140° from each other, hence the 120°/140° CCPM designation. Although t

• JR Vibe Fifty, Socket Head Bolt, 3x12mm (4 pcs) Socket Head Bolt, 3x8mm (4 pcs) Nylon Lock Nut, 3mm (2 pcs) Cross Member, 32mm Tank Stay (2pcs) Fuel Tank Holder (4pcs) ) 2 x ( d e R d e R ) 4 x ( 2-6 FUEL TANK INSTALLATION 15 Socket Head Bolt, 3x8mm (4pcs) Socket Head Bolt, 3x12mm (4pcs) Fuel Tank Holder (4pcs) Cross Member, 32mm (1pc) Nylon Lock Nut, 3mm (2pcs) Install the Tank stay in this drawing. Pass silicon tube thru this hole.

• Socket Head Bolt, 3x8mm (4 pcs) Flat Head Bolt, 3x6mm (6 pcs) Socket Head Bolt, 3x8mm (6pcs) Gyro Mount Gyro Frame Spacer (2pcs) Radio Bed Mount (3pcs) Front Radio Bed d e R ) 6 x ( d e R ) 6 x ( 2-9 FRONT RADIO BED INSTALLATION 3 18 Socket Head Bolt, 3x8mm (10pcs) Flat Head Bolt, 3x6mm (6pcs) Radio Bed Mount (3pcs)

• JR Vibe Fifty, Socket Head Bolt, 3x10mm (2pcs) Cross Member, 32mm (2 pcs) Socket Head Bolt, 3x8mm (2 pcs) Socket Head Bolt, 3x10mm (2 pcs) Socket Head Bolt, 3x8mm (4 pcs) Body Catch, 37mm (2pcs) Gyro Frame (2pcs) Nylon Lock Nut, 3mm (4pcs) d e R ) 2 x ( ) 2 x ( d e R ) 2 x ( d e R 2-8 FRONT RADIO BED INSTALLATION 2 17 Socket Head Bolt, 3x8mm (6pcs) Socket Head Bolt, 3x10mm (4pcs) Body Catch, 37mm (2pcs) Cross Member, 32mm (2pcs) Nylon Lock Nut, 3mm (4pcs)

• E) Travel Adjustment Move the roll selector until TRVL.ADJ is highlighted on the screen, then press the roll selector to enter the fun ction. Adjust the values as shown by moving the roll selector to highlight the desired channel, while using the control stick to select up/down, or left/right values to be adjusted. Please note that the required travel va

• JR Vibe Fifty, Flat Washer, 3mm (4pcs) Socket Head Bolt, 3x40mm (4pcs) Nylon Lock Nut, 3mm (4pcs) 400mm 350mm Drive Shaft Joint (2pcs) Setscrew, 3x10mm (2pcs) Tail Drive Shaft n e e r G ) 2 x ( d e R ne e r G ) 2 x ( It is very important that the guide bearing be attached to the shaft off center as shown to prevent resonance vibration and fatigue. 5-1 TAIL DRIVE SHAFT ASSEMBLY 5-2 TAIL BOOM INSTALLATION 31 Setscrew, 3x10mm (2pcs) Socket Head Bolt, 3x40mm (4pcs) Nylon Lock Nut, 3mm (4pcs) Flat Washer, 3mm (4pcs) Tail Boom Tail Boom Holder Shaft Drive GuideBearing, 8x14x4mm Oil Apply oil to the inside of Tail Boom, then install Sh

• JR Vibe Fifty, Item # Description Quantity 980147 SELF-TAPPING SCREWS, 2.6X10mm 10 980024 SELF-TAPPING SCREWS, 2x8mm 10 996177 COOLING FAN SHROUD 1 996178 FAN SHROUD COLLAR 4 960721 FAN HUB 1 980012 SOCK ET HEAD BOLTS, 3x6mm 10 960722 CLUTCH ASSEMBLY 1 970300 UPPER COLLET 1 960011 COOLING FAN BLADES 1 980030 BUTTON HEAD BOLTS, 3x5mm 10 970277 TAPER COLLET, LOWER 1 970503 THRUST WASHER L 2 980037 HEX NUTS, 2mm 10 980039 NYLON LOCK NUTS, 3mm 10 996176 ENGINE MOUNT 1 980022 SOCK ET HEAD BOLTS, 3x40mm 10 980036 PL ATE WASHERS, 3mm 10 980013 SOCK ET HEAD BOLTS, 3x8mm 10 980031 FL AT HEAD SCREWS, 2x8mm 10 970001 JOINT BALLS, 2X8mm SCREWS 10 98001

• * * * * Socket Head Bolt, 3x16mm (4pcs) Low Height Landing Strut, White (2pcs) Socket Head Bolt, 3x8mm (6 pcs) * : Don’t tighten bolts at this time. Nylon Lock Nut, 3mm (4 pcs) Flat Washer, 3mm (12 pcs) Bottom Frame Plate Landing Skid Long (2pcs) Landing Skid Cap (4pcs) Setscrew, 3x4mm (4pcs) A C ) 4 x ( 2-12 LANDING GEAR INSTALLATION 21 Socket Head Bolt, 3x8mm (6pcs)

• JR Vibe Fifty, Bearing Block w/Bearing, 10x19x7mm (3pcs) Bearing, F4x10x4mm (2pcs) Socket Head Bolt, 3x8mm (15 pcs) * : Don’t tighten bolts completely at this time. Center Bearing Case Direction Upper and Lower Bearing Case Direction Top Top Main Frame L Main Frame R Flat Washer, 3mm (4 pcs) Governor Mount Use this for attaching an Optical Governor Sensor. Optional governor ma gnets can be installed in the p redrilled holes in the clutch bell. Socket Head Bolt, 3x10mm ) 2 1 x ( d e R ) 2 x ( d l e W B J 2-1 MAIN FRAME ASSEMBLY 1 10 Socket Head Bolt, 3x8mm (15pcs) Socket Head Bolt, 3x10mm (1pc) Flat Washer, 3mm (4pcs) * * * * Note the proper direction and Bearing Blocks.

Related Products and Documents (Video Game Controller):

Comparable Devices:

Similar Resources:

• Hama THUNDER V5 (34 pages) 00051845/12.07 All listed brands are trademarks of the corresponding companies. Errors and omissions excepted, and subject to technical changes. Our general terms of delivery and payment are applied.Hama GmbH & Co KGD-86651 Monheim/Germanywww.hama.com …

• Logitech Driving Force Gt Steering Wheel (1 pages) LOGITECH® DRIVING FORCE GTPS3 racing gets real with the official wheel of Gran Turismo Hold on to your seat. Designed from the pedals up for PLAYSTATION 3 and Gran Turismo, this racing wheel lets you feel every bump in the road, crash and tire spin with jaw-dropping realism. With true-to-life race car steering, shifting, braking and acceleration, your ga …

• Microsoft WL3-00018 (5 pages) https://support.xbox.com/en-US/xbox-one/controllers/wireless-controller-solution https://support.xbox.com/en-US/xbox-one/accessories/connect-a-wireless-controller Troubleshoot your Xbox One wireless controller Your Steps 1 Welcome to the Xbox One Wireless Controller Solution Step 1: Welcome to the Xbox One Wireless Controller Solution If you’re having t …

• Microsoft XBOX (12 pages) 1XBOX ONE AND KINECT SENSOR PRODUCT GUIDEFor Xbox One console, Kinect for Xbox One sensor, and accessory product manuals, go to xbox.com/xboxone/support/manual.IMPORTANT PRODUCT SAFETY AND WARRANTY INFORMATION This symbol identifies safety and health messages in this product guideRead this guide for important safety and health information for the product t …

• Razer Raiju (20 pages) When it comes to console gaming, your controller is the most crucial weapon in your arsenal. Every component of the Razer Raiju for PlayStation®4 has been optimized to give you every possible competitive advantage—from four additional fully-programmable buttons, to the weight and shape of the controller, and even a Quick Control P …

• Black Horse Model Sea Futy (30 pages) Instruction Manual bookSPECIFICATION Wingspan : 1,671 mm 65.79 in. Length : 1,620 mm 63.78 in. Weight : 4.8 kg 10.56 Lbs. Parts listing required (not included). Radio : 08 channels. Servo : 8 S …

Comments, Questions and Opinions: