Manualios.com

Carl Goldberg Products Electra Instructions Manual

Carl Goldberg Products Electra Manual Online:

3.55, 1230 votes
Carl Goldberg Products Electra User Manual
Carl Goldberg Products Electra User Guide
Carl Goldberg Products Electra Online Manual

Text of Carl Goldberg Products Electra User Guide:

  • Carl Goldberg Products Electra, 8.  Trial fit the fin in place on the fuse/stab assem- bly.  Use a 90º triangle to make sure the fin is per- pendicular to the stab.  Strip covering from the areas of contact on both the stab top and the fin bottom. Agaiin, be certain to leave about 1/8” of covering in the area of contact.  When satisfied that the fin and stab are square, glue in place with JET 6 Epoxy™ or Slow Jet™. 9.  From the 4” piece of tri-stock balsa, cut two 2” pieces.  Round the ends by sanding lightly to improve fit.  Position the tri-stock at the fin/stab joint and trace the

  • Carl Goldberg Products Electra,  When dry, gently slide the hatch away from the fuse bottom sheet. 4.  Position 1/8” square x 7-3/8” bass rails behind the hatch tongue and flush with the hatch sides. Glue in place.  Positiion the 1/16” ply doubler at the end of the hatch, as shown. Glue in place. 5.  From 3/16 x 3/8” scrap material (from stab), cut and glue a strip to match the top of Former “B”.  From 5/64 x 3/16” scrap (stab trussing materi- al), cut and glue a strip to match the bottom of Former “B”.  Using additional 5/64 x 3/16” ma

  • SHEET 4001 WING RIBS 5/64 x 2-7/8” 2 REQ’D. SHEET 4002 WING RIBS 5/64 x 2-7/8” 2 REQ’D. DIE-CUT WOOD SHEETS SHEET 4006 3/16x 2-7/8 x 9-1/2” 1 REQ’D. SHEET 4008 1/16x 2-5/8 x 13-1/2” 1 REQ’D. SHEET 4011 1/16x 2-5/8 x 13-1/2” 1 REQ’D. SHEET 4010 1/16x 2-7/8 x 18” 1 REQ’D. BATTERY HATCH FORMER C DOUBLER HATCH DOUBLER SHEET 4009 1/8x 2-3/8 x 17” WING CENTER JOINERS 1

  • Carl Goldberg Products Electra, Apply covering to the solid bottom pieces, wrapping and sealing around the edges. If necessary, slit the corners for a smooth appearance.Apply covering to the sides next, and then to the top. Make sure to over- lap seams at least ¼”, so that when high heat is applied, the shrinking will not create a gap. Cover the hatch bottom, carefully sealing around the edges. Trim the covering even with the hatch bottom and remove the covering from the ventilation holes. When covering the top of the fuse, do not cover the stap platform, as proper installation of the stab requires a wood-to-wood b

  • Carl Goldberg Products Electra, ADHESIVES & GLUING TECHNIQUES The ELECTRA was designed for fast assembly using SUPER JET™ CA (cyanoacrylate adhesive), which is spe- cially formulated to firmly glue the plywood, hardwood, and balsa used in your model and to withstand vibration. However, there are times, such as when you are installing the stabilizer and fin on the fuselage and want more set-up time for careful alignment and positioning, when you should use JET EPOXY™. Occasionally, you also will want to use INTANT JET™, which "wicks" into the surrounding areas. Aliphatic resin glue or similar water-based glues can also be used, but they will add to the assembly time because they dry so much more slowly

  • Carl Goldberg Products Electra, FLYING THE ELECTRA LEARNING TO FLY Flying R/C is both fun and challenging. As with other portions of this book, the following section is meant to introduce you to the basics. Read carefully before tak- ing your model out to the field and attempting first flights. And remember, becoming an R/C pilot takes time and patience, but the rewards are well worth the effort. Equipment Checklist  Flight batteries, fully charged  Extra battery packs  Radio transmitter  Battery charger  To

  • Carl Goldberg Products Electra, 13.  Turn the fuse over and position the 1/16” ply front bottom sheet on the fuse sides, behind Former “A.”  Tape the sheet in position and then glue the joints. When dry, remove the tape and apply the glue to the taped areas. 14.  Referring to the plan, spread the fuse sides slightly and insert the motor mount support into the notches. IMPORTANT! The side stamped “R” must be positioned on the right side of the model.  Glue the motor mount support in place.  Then, insert and glue the two Former “A” dou- blers in place behind Former “A.” 16.  Place the battery hatch in the fuse bottom and position a nylon flat

  • Carl Goldberg Products Electra, TAIL CONSTRUCTION 1.  Collect the following items. (4) 3/16 x 3/8 x21” BALSA PT. #4853 (1) 1-3/4 SQ. x 21” BALSA PT. #4696 (3) 5/64 X 3/16 X 24” BALSA PT. #4698 (1) 1/2” SQ. x 8-1/4” BALSA PT. #4701 (1) D/C SHEET 4006 BALSA PT. #3606 containing: Stab center platform Stab leading edge joiner Wing and tail gussets Stab tips Dorsal fin (1) CENTERLINE MARKER PT. #1425 (7) SMALL FLEX-POINT HINGE PT. #1448 2.  Lay the horizontal stabilizer portion of the plan over the building board and cover with waxed paper.  Buidling over the plan, carefully cut two 3/16 X 3/8” balsa sticks to form the stabilizer leading edge. Make sure to exactly match the plan from the

  • Carl Goldberg Products Electra, IMPORTANT! Installation of the Turbo 550 motor and a typical radio system is described in this booklet. Depending on the equipment you are using, you may not be able to follow exactly these instructions. Follow the installation instructions included with your equip- ment or seek help from your local hobby dealer. Before beginning, make sure that each of the following items have been completed: 1. Model is fully covered and painted, if required. 2. All control surfaces are hinged in place. 3. The tail assembly is glued solidly to t

  • Carl Goldberg Products Electra, SETTING CONTROL SURFACES All pushrods must move freely, without binding. Adjust them, if necessary, for smooth operation. When set- ting the travel (movement of rudder or elevator), make certain that no servo is hooked to a pushrod in a man- ner that prevents the servo wheel from moving through its full range of motion. For example, if the servo motor “buzzes,” when moved to the ON position, the servo still has movement, but it is jammed against the limit position. This can damage the servo and drain the battery, leading to loss of control and a crash. 1.  With the elevator trim tab on the Tx set in the center, or neutral, position, screw the mini- snap on the

  • Automatic Chargers. DELTA or PEAK DETECTION CHARGERS are excellent methods of charging a bat- tery, as one simply connects the charger, pushes the start button, and waits. Within approximately 15-30 minutes, the battery may be disconnected and used. It is still a good idea to monitor the battery temperature (by lightly touching) every minute or so after 10 min- utes of charging. If you s

  • MOTOR INSTALLATION IMPORTANT! PLEASE READ THIS SECTION BEFORE BEGIN- NING MOTOR & RADIO INSTALLATION. FAILURE TO FOLLOW THESE PRECAUTIONS CAN LEAD TO SERIOUS PERSONAL INJURY TO YOURSELF OR OTHERS, AND CAN RESULT IN PROPERTY DAMAGE. SAFETY PRECAUTIONS: WHEN OPERATING THE MOTOR: z ALWAYS wear eye protection! z KEEP AWAY from spectators! z KEEP AWAY FROM CHILDREN. DO NOT al

  • Carl Goldberg Products Electra, 1.  Insert the soft rubber grommets into the mount- ing holes of your servos. 2.  Measure from the bottom of your servo to the underside of a grommet. Add about 1/8” to this measurement to get the total distance between the wing platform and the servo rail.  Referring to the plan, glue the rear rail against Former “C”, at the predetermined height.  Place a servo on the rear rail and determine the location of the front rail. Be sure to allow enough clearance to allow easy insertion and removal of both servos.  Glue the front servo rail in place. 3.  Place both the rudde

  • Carl Goldberg Products Electra, 13.  Next, cut 45º slots on each side of each hole to accommodate the hinge webs. NOTE: The CGM hinge slotting kit (Item # 600) is handy for this process. 14.  Move the elevator close to the edge of the table and support the thin edge with wing rib scrap, as shown.  Carefully cut hinge slots, as, at the proper loca- tions. 15.  Repeat the slotting method for the fin and rud- der. 16.  Referring to the above diagrams, assemble the beveling tool. First glue the narrow strip to the handle, taking care to keep it square. Then glue the wide

  • Carl Goldberg Products Electra, In flight, the model is controlled by using the rudder and the elevator (see drawing). One radio channel controls the rud- der, which is the primary turn control. It rolls, or "banks" the model. Another channel operates the elevator, which controls the pitch (climbing, level flight, and descent). The third chan- nel is for the motor. Radios are battery powered with rechargeable nickel- cadmium batteries (ni-cads). Such sets come equipped with a recharging unit. Also, many of the radio systems now avail- able feature "servo reversing" switches which allow the pilot to reverse the response of the

  • Carl Goldberg Products Electra, WING CONSTRUCTION IMPORTANT: YOU WILL BE BUILDING A RIGHT AND THEN A LEFT WING. FOLLOW THE STEPS CAREFULLY TO AVOID CONFUSION. 1.  Collect the following items: (2) D/C SHT. 4001 5/64” Balsa PT. #3601 Contains: WING RIBS (2) D/C SHT. 4002 5/64” Balsa PT. #3602 Contains: WING RIBS (1) D/C SHT. 4006 WING GUSSETS PT. #3606 (1) D/C SHT. 4008 1/16” Ply PT. #3608 Contains: POLYHEDRALJOINERS (1) D/C SHT. 4009 1/8” Ply PT. #3609 Contains: WING CENTER JOINERS (1) D/C SHT. 4010 Balsa PT. #3610 (2) D/C SHT. 4012 1/16” Balsa PT. #3612

  • Carl Goldberg Products Electra, REMOVABLE TIP OPTION NOTE: The materials needed to make the wing tip removable are NOT INCLUDED in your kit. Necessary templates for this option are found in the upper right corner of the wing half of the plan. Follow these steps ONLY IF YOU WANT TO BE ABLE TO REMOVE THE WING TIPS. Otherwise, continue at Step 14. A.  Collect the following items: 1/8” x 3” x 18” HARD BALSA SHEET 3/32” x 12” MUSIC WIRE 3/32 I.D. x 6” BRASS TUBE 3/34” VINYL ELECTRICAL TAPE B.  Make a sanding block from 1/8” scrap plywood, using the SANDING ANGLE TEMPLATE from the plan. Make sure to establish tthe proper sanding block angle, as show above. C.  From the 1/8” hard bal

  • Carl Goldberg Products Electra, ABOUT THE WOOD IN THE KIT We strive to supply good quality materials in your kit. Wood parts are inspected with regard to the function they will serve. If an imperfection is spotted in a scrap corner of a die-cut sheet and doesn't affect actual parts, the sheet is considered acceptable. Also, internal stresses in wood are relieved as it is cut into parts. These relieved stresses may cause some parts to bow. Bows in wood parts (such as leading edges) readily straighten out as they are Super Jeted into a structural unit WOOD PARTS Be careful when removing parts (such as fuselage sides) from the die-cut sheets. Long parts are fr

  • Carl Goldberg Products Electra, COVERING INTRODUCTION There are several ways to cover the frame of a model airplane. Years ago, the open framework of most air- planes was covered with a combination of tissue (or silk) and dope; the solid structures were painted. Today, most models are covered with polyester films that resemble either a painted finish or a fabric finish. These films are easy to apply and actually increase the strength of the aircraft. The following instructions describe the general procedure for covering a model. However, it is important to carefully read the instruc- tions that come with the film, as different products are applied in somewhat different ways.

  • Carl Goldberg Products Electra, The Electra was designed for long, slow, relaxed flying - not loops or similar aerobatic maneuvers. Save that kind of lying for your next, higher performance sport plane. Practicing precise control and glide planning on the Electra is good preparation for the demands of advanced aerobatic flying. We recommend you use 3 channels, as this will allow you to cut power whenever you wish to do so. On your first few flights, after a couple of minutes, you may feel you have "had enough" and want to land and relax. A 2-channel system without motor control will not give you this option; you will have to keep flying until the battery pow

  • Carl Goldberg Products Electra, ITEMS NEEDED TO COMPLETE KIT RADIO GUIDANCE SYSTEM (2-CHANNEL MINIMUM) 6 CELL 7.2 VOLT BATTERY PACK 2-OZ. BOTTLE CA GLUE 3 ROLLS COVERING 1 TUB JET MODEL MATE™ FILLER BOX OF #64 RUBBER BANDS BATTERY CHARGER SPOOL OF SEWING THREAD ADDITIONAL ITEMS FOR REMOVABLE WINGTIP 1/8” x 3” x 18” HARD BALSA SHEET 3/32” x 12” MUSIC WIRE 3/32 I.D. x 6” BRASS TUBE 3/4” VINYL ELECTRICAL TAPE OPTIONAL ITEMS 1/2” x 8” x 12” CGP FOAM RUBBER FUEL PROOF PAINT™ SERVO MOUNTING TAPE SPARE MOTOR FUSES 1-1/2” WHEEL 3/32” x 8” WIRE 3/32” WHEEL COLLAR 3/8” LANDING GEAR STRAP TRANSPARENT SPRAY ENAMEL FOR CANOPY FOR USE WITH CGP TU

Related Products and Documents (Video Game Controller):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Emerson 200I/48-NT5C05C Installation and user manual emerson/200i-48-nt5c05c-716.pdf 31 Aug 2023 62 0.34 Mb
2 Philips GoGear SA2446BT/97 Specifications philips/gogear-sa2446bt-97-R3M.pdf 08 Oct 2023 3 0.47 Mb
3 Poulan Pro 3300 Operator's manual poulan-pro/3300-DMW.pdf 09 Jun 2023 24
4 Technics SD-S9225 Operating instructions manual technics/sd-s9225-5Y1.pdf 01 Mar 2023 60 2.73 Mb
5 Pro.Mecc Freccia Maintenance manual pro-mecc/freccia-OV2.pdf 20 Sep 2023 27
6 Polaroid LCD-1550 Operation manual polaroid/lcd-1550-6J1.pdf 18 Jan 2024 20

Similar Resources:

  • Sony

    PlayStation 4

    (2 pages)
    How to set up your Sony PlayStation 4. In this video, we'll show you how to get your PS4 up and running. Note: Don't throw away the box your PS4 came in. It's designed to be used as a carrying case so you can transport your console safely. Connect the console to your TV. • Connect the included HDMI cable to your TV and the PS4's HDMI …
  • Sony

    PLAYSTATION VR

    (40 pages)
    4-588-818-14(1)CUH-ZVR1Instruction ManualMode d’emploiIncludes important Health and Safety informationComprend des informations importantes relatives à la santé et la sécurité …
  • Saitek

    Cyborg evo Wireless

    (36 pages)
    Cyborg evo Wireless User Manual Getting Started Features: Battery Your Cyborg evo Wireless uses one AA alkaline battery (supplied) which should give up to 50 hours of use. To fit the battery, open the battery compartment on the bottom of your joystick by sliding back the cover. Insert the AA battery in the direction shown and replace the cover. LED power st …
  • GameSir

    G5

    (2 pages)
    GameSir G5User Manual1.Product Description 3.Product Overview2.Product Specifics L2 ButtonL5 ButtonL4 Button R4 ButtonL1 Button R1 ButtonUSB Charging PortR2 ButtonMode ButtonPOWER ButtonMode Indicator LightsHOMEButtonSELECT ButtonSTARTButtonTURBO ButtonLeft JoystickD-PadABXY TrackpadFunction ButtonFunctionButtonR5 ButtonWe hope this manual can answer the que …
  • Hama

    00034383

    (5 pages)
    Wireless Guitar Controller00034383 w ww.hama.com H ama GmbH & Co KGPostfach 80 86651 Monheim/GermanyTel. +49 (0)9091/502-0 Fax +49 (0)9091/[email protected]
  • GamerModz

    JUGGERNAUT

    (22 pages)
    – INSTRUCTION MANUAL PS4 – JUGGERNAUT VER 5.0 Congratulations, welcome to the GamerModz Family! You are now a proud owner of a GamerModz Custom Modded Controller. The JUGGERNAUT - VER 5.0 FOR PS4 has been completely redesigned from the ground up to maximize your gameplay experience. It includes a much faster processor allowing you turn mods on and o …

Comments, Questions and Opinions: