Manualios.com

Carl Goldberg Products Stinson 108 ARF Operation & User’s Manual

  • Stinson 108 ARF Video Game Controller
  • maol9bWePwoTQ
  • Operation & User’s Manual
  • PDF / Adobe Acrobat Reader
  • 19

Carl Goldberg Products Stinson 108 ARF Manual Online:

3.35, 2534 votes
Carl Goldberg Products Stinson 108 ARF User Manual
Carl Goldberg Products Stinson 108 ARF User Guide
Carl Goldberg Products Stinson 108 ARF Online Manual

Text of Carl Goldberg Products Stinson 108 ARF User Guide:

  • WARNING A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep this kit out of the reach of younger children, as it contains parts that could be dangerous. A radio- controlled model is capable of causing serious bodily injury and property damage. It is the buyer's responsibility to assemble this aircraft correctly and to properly install the m

  • Carl Goldberg Products Stinson 108 ARF, 2 INTRODUCTION USING THIS INSTRUCTION MANUAL Before you begin assembling your Stinson ARF, take some time to read through this entire instruction book. It is designed to take you step-by-step through the process and to give you added information on engine and radio selection and set-up, balancing your aircraft, and flying your model. The time you spend will speed the assembly process and help you avoid problems. PREPARING FOR ASSEMBLY You will need a work area of approximately 24 x 70" which has been covered to protect it from adhesive, as well as cuts and other damage. Many people cover their work area with a sheet of dry wall (sheet rock) and/or

  • Carl Goldberg Products Stinson 108 ARF, 3 ITEMS NEEDED TO COMPLETE THIS AIRCRAFT  1 RADIO GUIDANCE SYSTEM (6 CHANNEL MINIMUM REQUIRED WITH 8 SERVOS)  2 12” AILERON SERVO EXTENSION WIRES  2 24” ELEVATOR SERVO EXTENSION WIRES  3 Y-HARNESS (1 with reversing)  1 ENGINE .61-.108 2-STROKE, .91- 1.20 4- STROKE AND MUFFLER  1 CA ACCELERATOR  1 2 OZ. BOTTLE CA MEDIUM GLUE  1 1/2 OZ. BOTTLE CA THIN GLUE  1 20 MINUET EPOXY  1 1/4” FOAM RUBBER  1 20” String NOTE: The Stinson ARF covering matches White (#870), Deep Blue (#873) and True Red (#877) Oracover. TOOLS AND SUPPLIES FOR ASSEMBLY.  MO

  • Carl Goldberg Products Stinson 108 ARF, 4 2.  Locate the pre-cut aileron hinge slots and flap slots in both wing halves. Using a hobby knife (#11 blade), slide the blade into each slot to make sure it is cleanly cut.  Repeat this process with the ailerons and the flaps, making sure all hinge slots are clean. 3.  Place a straight pin into the center of each of the four CA hinges.  Slide each hinge into the hinge slots on one of the wing halves. The pin will prevent the hinges from going further than halfway into the wing. 4.  Select the aileron and flap for the wing on which you are working on and insert the exposed half of each hinge into the aileron slots.  Slide the aileron toward the wing until no g

  • 5 AILERON SERVO INSTALLATION Note: The following pictures may not exactly match the hardware you are using. Always check the radio manufacturer's instructions when installing radio equipment. 1.  Collect the following items: (16)Servo mounting screw (supplied with radio) (4) Servos with rubber grommet & eyelets(sup- plied with radio) (2) 12” servo Extension (for the aileron servo

  • Carl Goldberg Products Stinson 108 ARF, 6 2.  With the aileron servo in place, make a mark at a 90º degree angle to the trailing edge and in line with the servo arm. 3.  Position the control horn bolt so that it is 3/4” back from the hinge line on the mark that you just made. 4.  Using a 9/64" drill bit, make a hole in the aileron through to the top side. 5.  Insert the 6-32 x 2” screw from the top through the aileron.  Place the #6 washer and the 6-32 hex nut on the bolt and tighten. Make sure that you use thread lock on the bolt and nut.  Screw the bla

  • Carl Goldberg Products Stinson 108 ARF, 7 TAIL CONSTRUCTION * Collect the following items (2) Right & left Stab (1) 10mm x 182mm front stabilizer tube (1) 10mm x 312mm Rear Stabilizer tube (2) 4-40 x 3/8 Socket head screw 1.  Slide the short stabilizer tube into the front hole and long stabilizer tube in the rear hole of one side of the stab. Then slide the assembly into the holes in the fuselage till the stab is flush against the fuse. (The side of the stab with the hole is the top of the stabilizer). Slide the second stab onto the tubes sticking out the other side of the fuselage. Squeeze both stab pieces togethe

  • Carl Goldberg Products Stinson 108 ARF, 8 5.  With the servo in place, remount both stabiliz- ers and make a mark at a 90º degree angle to the elevator hinge line, and in line with the servo arm.  Position the control horn bolt so that it is 3/4” back from hinge line on the mark that you just made. 6.  Using a 9/64" drill bit, make a hole in the ele- vator through to the top side. 3.  At the rear of the fuselage just below the front of the stabilizer you will find the servo cut outs on both sides of the fuselage. The top cut out is for the elevator serv

  • Carl Goldberg Products Stinson 108 ARF,  Make a slot on the hinge line for the bracket. Make sure that the bracket and wire is between the fuselage and the rudder. 4.  Install the hinges into the rudder and glue the rudder in place using the same hinging method used for the elevator and ailerons.Remember to leave a 3/32” gape at the top of the rudder.  Position the rudder control horn bolt so that it is 1/4” back from hinge line and 1” up from the bottom of the rudder.  Using a 9/64" drill bit, make a hole in the rud- der. 9 RUDDER AND RUDDER CABLES  Collect the following items: (1) 6-32 x 3”

  • 10 9.  Insert the throttle tubing into the rear cable exit hole.  Push the tubing into the fuselage while allow- ing the tubing to pass through the holes in the rear former inside the fuselage.  Push the tubing forward, guiding it through the fuselage. 10.  Insert the 2-56 end of the cable into the throt- tle tubing by the rudder, and pull the tubing

  • Carl Goldberg Products Stinson 108 ARF, 11 INSTALLING THE LANDING GEAR  Collect the following items: (6) 10-32 x 1” Socket Head Bolts (4) #10 Washers (2) Landing Gear (left & right) (2) Lower Wing Strut Brackets 1.  Determine which is the front of the landing gear. 2.  Insert the left landing gear into the slot on the bottom of the fuselage.  Slide the lower wing strut bracket into the slot found above the landing gear slot.  Place thread lock on one of the 10-32 x 3/4” bolts, and insert it through the wing bracke

  • 4.  Place the wheel pant over the axle.  Install one wheel collar with set screw then the wheel, finally the second wheel collar with set screw.  Using thread lock, tighten the wheel pant to the landing gear.  Center the wheel on the axle using the wheel collars on both sides of the wheel. 12 Even 2.  Hold the bottom of the wheel pant level with the bottom of the landing gear.

  • Carl Goldberg Products Stinson 108 ARF, 13  Gather the following items (1) fuel tank (1) rubber tank stopper (1) clunk (1) 3mm x 25mm screw (1) cap washer large (1) cap washer small (2) 3mm x 40mm brass tube (1) 3mm x 60mm brass tube (1) silicone tube 4mm x 80mm (3) silicone tube 5mm x 165mm 1.  Insert the 3mm screw through the center hole in the large washer, through the center hole in the rubber washer against the large side, and screw the small washer on the back side. 2.  Insert the brass tubes through three of the holes. They should be arranged so as the long one will be on the right side of the plane and the short one on the left side.  The tubes should extend out the

  • Carl Goldberg Products Stinson 108 ARF, 14 INSTALLING THE ENGINE 1.  Collect the following items: (2) Motor Mounts (1) Engine (4) #10 x 3/4” sheet metal screw (10) 8-32 x 1” Philip Head Screw (10) #8 Washer (1) 3mm x 430mm Tubing (1) 1.5mm x 490mm wire (1) swivel-Keeper (1) Pushrod Connector (1) Snap Nut (1) 4-40 x 1/8 Socket Head Screw (1) Wood firewall spacer (4) 8-32 Blind Nut INSTALLING FUEL TANK 1.  Gather the following items (1) Foam Rubber (Not Included) (1) Fuel tank tray (1) Fuel tank 2.  Cut a piece of foam to fit under the fuel tank.  Mount the fuel tan

  • Carl Goldberg Products Stinson 108 ARF, 15 3.  Keeping the engine perpendicular to the table top, clamp the other motor mount to the engine. Mark and drill the second motor mount then screw the mount to the engine. 5.  Install the motor mount beams on to the fire- wall plate using the 8-32 x 3/4” socket head screws and washers and 8-32 blind nuts USE THREAD LOCK ON ALL SCREWS 4.  Place the motor mount onto the firewall mounting plate.  Center the motor over the horizontal and ver- tical lines. 6.  Mount the firewall plate to the front of the fuse- lage using the 8-32 x 1/2” 5.  Drill a 1/8” hole in the firewall in

  • Carl Goldberg Products Stinson 108 ARF, 16 7.  Mount throttle servo in the servo tray. Note: Your installation may vary depending on the engine used.  Install pushrod connector on your servo arm and attach to the throttle servo. 8.  Insert the .pushrod wire through the connec- tor on the servo arm.  Locate the proper positioning of the throttle servo arm. Then cut off the excess wire, keep- ing some wire for future adjustments. PUSHROD CONNECTOR SNAP NUT INSTALLING THE COWL  Collect the following items: (1) Cowl (4) 2mm x 5mm Philip head screws

  • Carl Goldberg Products Stinson 108 ARF, 17 7.  Remove the cowl and, with a moto tool, slow- ly remove the fiberglass INSIDE the cutout outline. Work slowly and carefully, until the cowl matches the clear plastic piece.  Remember, if the fiberglass is damaged dur- ing this process, it can be repaired only with epoxy glue. NOTE:You may wish to make a cutout in the front of the cowl, at the point where the engine prop washer sticks out, that is large enough to allow the engine to vibrate without touching the cowl. 8.  Remount the engine and remove any fiber- glass on the cowl that interferes with the eng

  • Carl Goldberg Products Stinson 108 ARF, 18 Remove 3.  Place the windshield onto the front of the fuse- lage.  Using a pencil, mark where the windshield over lap's the side of the fuselage where the wing will fit. 11.  Cut the plastic till it is flush with the side of the fuselage and so that the wing will fit flush against the fuselage.  Once satisfied with the fit glue the windshield in place using a canopy glue.  Tape the windshield to the fuselage till dry. BOLTING ON THE WING  Gather the following items (1) Right & Left Wing Panels (2) 1/4-20 x 2” Nylon Bolt (1) Wing Tube  Slide the wing tube into one of the wing halves.  Slide the tube thru the fuselag

  • Carl Goldberg Products Stinson 108 ARF, 19 3.  Starting with the front of the wing strut, attach the bottom clevis to the lower strut bracket.  Keep twisting the upper clevis till the strut fits snug between the lower and upper attach- ment points.  When satisfied, attach the upper front strut clevis to the wing 1.  Using glass cleaner and a soft cloth, clean the model surface thoroughly before applying decals. 2.  Cut the decal sheets apart in sections, as needed.  Fold the decal in half, front to rear. Open at the fold and place the decal on a flat surface. The protective backing will bubble away from the decal at the fold. DECAL APPLICATION  Adjust and attach the rear strut to the wing.  Tight

Related Products and Documents (Video Game Controller):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Garmin GFS 10 - Fuel Sensor Quick reference manual garmin/gfs-10-fuel-sensor-P9R.pdf 06 Jan 2023 24 0.37 Mb
2 Lennox HS27 Owner's manual lennox/hs27-14U.pdf 13 Sep 2022 2
3 GE 26929C/D Operation & user’s manual ge/26929c-d-4D9.pdf 08 Oct 2022 2 0.21 Mb
4 moon W-8 Owner's manual moon/w-8-2JG.pdf 14 Dec 2022 11
5 Labconco 44000 Series Operation & user’s manual labconco/44000-series-NYF.pdf 17 Nov 2023 107
6 Acer Aspire easyStore Series Operation & user’s manual acer/aspire-easystore-series-1PS.pdf 30 Sep 2022 148 18.09 Mb

Similar Resources:

  • HORI

    PRO

    (12 pages)
    ■ Includes / Inclus / inklusive / Incluso / Incluye■ Platform / Plateform / Plattform / Piattaforma / PlataformaInstruction manual/ Mode d'emploi/ Bedienungsanleitung/ Foglio di istruzioni/ Hoja de InstruccionesQuick Start Guide/ Guide de démarrage rapide / Schnellstart-Anleitung/ Guida introduttiva/ Guía de inicio rápidoMouse & Keyboard Cont …
  • XBOX

    360

    (2 pages)
    Xbox 360 ChatpadThanks for choosing the Xbox 360® Chatpad. Chatpad attaches to the back of your Xbox 360 wired or wireless controller to enable in-game text messaging, instant messaging, and other text entry. The keypad is optimised for fast, thumbs-only typing.To use Chatpad for messaging, you need an Xbox LIVE® membership. For information about Xbox LIVE …
  • Endor

    FANATEC ClubSport Wheel Base V2.5

    (2 pages)
    WARNING!WARNUNG!ATTENTION!EN Do not open/loosen these screws.DE Diese Schrauben dürfen nicht geöffnet / gelockert werden.FR Ne pas ouvrir / desserer les visEN For detailed information please download the manual from www.fanatec.com/support. This is just a QuickGuide and you will miss a lot of features if you don’t read the manual. Driver - PC: Ple …
  • StarVR

    C702

    (81 pages)
    CONTROLLER QUICK GUIDEGUIDE RAPIDE DU CONTRÔLEUR / GUIDA RAPIDA DEL CONTROLLERCONTROLLER KURZANLEITUNG / GUÍA RÁPIDA DEL CONTROLADORコントローラー クイック ガ イド / 컨트롤러 빠른 시작 설명서動作控制器快速指南 / 控制器快速指南 …
  • Pretorian

    Optimax Joystick

    (2 pages)
    Pairing TroubleshootingIf your OPTIMAX JOYSTICK unit does not operate correctly, pleaseuse the following guide to determine the cause. If, after followingthis guide, your unit still does not operate, please contact your sup-plier before returning it:SymptomWarrantyYour OPTIMAX JOYSTICK is warranted for 24 months from date of purchase against defects in manuf …
  • Horizon Hobby

    Blade MCX Tandem Rescue

    (22 pages)
    EFLH2500© 2009 Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, IL 61822USAHorizon Hobby UK Units 1-4 Ployters Rd Staple Tye Harlow, Essex CM18 7NSUnited KingdomHorizon Hobby Deutschland GmbH Hamburger Strasse 10 25335 Elmshorn GermanyE-flite® products are distributed exclusively by Horizon Hobby, Inc.US patents 7,391,320D578,146PRC patent ZL 2007200690 …

Comments, Questions and Opinions: