ACTi B94 Hardware Manual
|
ACTi B94, www.acti.com Hardware Manual 9 Physical Description Below is an illustration of the camera module. 1) Ethernet Port Connects to a network using an Ethernet cable. 2) DC 12V Power Input In case the camera is connected to a non-PoE (Power over Ethernet) switch, use this connector to connect the camera to an external power adapter (not included). See Connecting a Power Adapter (Optional) on page 29 for more information. 3) Reset Button The purpose of reset button is to restore the factory default settings of the camera, including the administrator’s
ACTi B94, www.acti.com Hardware Manual 30 4. Tighten the screws of the 12V pin and the GND pins to secure the wire connection. 5. Set the prepared power adapter for connection later. Below is an example of a power adapter with an attached terminal block. NOTE: The power adapter is not bundled in the package.
www.acti.com Hardware Manual 47 Assuming that the camera’s IP address is 192.168.0.100, you can access it by opening the Web browser and typing the following address into Web browser’s address bar: http://192.168.0.100 Upon successful connection to the camera, the user interface called Web Configurator would appear together with the logi
ACTi B94, www.acti.com Hardware Manual 37 How to Replace the Dome Cover For more discrete surveillance needs, the bundled dome cover can be replaced with a smoke, vandal proof cover available for purchase. To replace the dome cover, do the following: 1. Loosen the three (3) screws to open the dome cover. 2. Using a screwdriver, remove the screw securing the spring wire to the dome cover. NOTE: Hold the spring wire as the screw is being removed to avoid the sudden release of the screw and cause it to fly in the air. 3. Remove the three (3) screws to detach the cover bracket.
ACTi B94, www.acti.com Hardware Manual 26 10. Connect the network cable to the Ethernet port and other cables (if any) to the corresponding connectors on the camera. If necessary, install also the memory card at this point. 11. Align the camera module to the guide on the housing. 12. Tighten the three (3) screws to secure the camera module to the housing. 13. Proceed with Step 4: Install the Camera to the Surface on page 27. Ethernet Port Digital Input / Output (DI/DO) and Audio Input / Output Conne
www.acti.com Hardware Manual 40 10. Fit the screw into the spring wire that is attached to the camera. Note the screw placement as shown below. 11. There are two (2) screw holes on the bracket, attach the screw to the right screw hole using a screwdriver. Final installation should look like the illustration below.
ACTi B94, www.acti.com Hardware Manual 33 High Voltage DO Device Connection Even though the camera provides 12V power, this may not be enough for some high voltage DO devices, such as a ceiling light or a motor that opens or closes a gate. In this case, there is a need to connect an external relay. See wiring scheme below: Note that when choosing an appropriate relay, please refer to its specifications and make sure they match the above design. The triggering circuit voltage h
ACTi B94, www.acti.com Hardware Manual 12 Mount Types Accessories Straight Wall Mount Suitable when mounting the camera on straight walls. PMAX-0308 (L-Type Wall Mount) PMAX-0101 PMAX-0305 (Heavy Duty Wall Mount) Vertical Pole Mount Suitable when mounting the camera on vertical poles. PMAX-0101 PMAX-0305 PMAX-0503 Horizontal Pole Mount Suitable when mounting the camera on horizontal poles. PMAX-0101 PMAX-
ACTi B94, www.acti.com Hardware Manual 22 Waterproof Solution with Conduit This section describes the procedures to waterproof the cabling connections using the bundled conduit gland and flexible conduit. This is the recommended solution if an exterior-grade Ethernet cable is not available or when other cables, such as power adapter, DI/DO devices, etc., will be connected to the camera. If other connectors will be connected or a memory card will be installed, the camera module must be removed from the housing first. See How to Remove the Camer
ACTi B94, www.acti.com Hardware Manual 7 Introduction The List of Models This hardware manual contains the following models: B94 1.3MP Outdoor Mini PTZ with D/N, Basic WDR, SLLS, 10x Zoom lens B95 2MP Outdoor Mini PTZ with D/N, Basic WDR, SLLS, 10x Zoom lens B96 5MP Outdoor Mini PTZ with D/N, Basic WDR, 10x Zoom lens B97 3MP Outdoor Mini PTZ with D/N, Superior WDR, 10x Zoom lens From the installation perspective these models are very similar; therefore you can use one manual for all of them.
ACTi B94, www.acti.com Hardware Manual 19 Waterproof Solution with Naked Cable This section describes the procedures in using the bundled cable gland and an exterior-grade Ethernet cable. 1. Disassemble the cable gland as shown below: 2. Insert the clamping nut into the Ethernet cable. 3. Insert the sealing insert with claw. Body (with Washer) Sealing Insert with Claw Clamping Nut
ACTi B94, www.acti.com Hardware Manual 44 Use the default IP address of a camera: If there is no DHCP server in the given network, the user may have to assign the IP addresses to both PC and camera manually to make sure they are in the same network segment. When the camera is plugged into network and it does not detect any DHCP services, it will automatically assign itself a default IP: 192.168.0.100 Whereas the default port number would be 80. In order to access that camera, the IP address of the PC has to be configured to match the network segment of the camera. Manually adjust the IP addr
ACTi B94, www.acti.com Hardware Manual 13 Other Mounting Accessories Accessories PMAX-0104 (Extension Tube) PMAX-0700 (Junction Box) NOTE: For more information about the mounting solutions and accessories, please check the Mounting Accessory Selector in our website (http://www.acti.com/mountingselector). The above mounting accessories are not included in the package. Contact your sales agents to purchase.
ACTi B94, www.acti.com Hardware Manual 29 Other Connections This section describes the procedures in preparing the external devices that you can connect to the camera. The camera supports DC12V power input, Digital Input and Output (DI/DO) and Audio Input and Output devices using the bundled terminal blocks. The use of these devices, however, is optional. Connecting a Power Adapter (Optional) In case of using a non-PoE switch or your PoE switch has limited power supply, you can purchase a power adapter and directly connect the camera to a power outlet. The power adapter must be connected to the supplied terminal bl
ACTi B94, www.acti.com Hardware Manual 3 Other Adjustments and Accessories .................. 35 How to Remove / Install the Camera Module......................................... 35 How to Remove the Camera Module .................................................... 35 How to Install the Camera Module ........................................................ 36 How to Replace the Dome Cover ............................................................ 37 How to Insert / Remove a Memory Card ................................................ 41 How to Insert the Me
ACTi B94, www.acti.com Hardware Manual 4 Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment. Servicing Do not attempt to service this video device yourself as opening or removing covers may expose you to dangerou
www.acti.com Hardware Manual 14 Installing the Camera on a Surface This section describes the procedures in installing the camera on a flat surface such as a hard or dropped ceiling and straight or tilted walls. Before installation, make sure the wall or the ceiling can bear more than the weight of the camera. Step 1: Drill the Holes
ACTi B94, www.acti.com Hardware Manual 35 Other Adjustments and Accessories How to Remove / Install the Camera Module How to Remove the Camera Module The camera module must be removed from the housing in the following situations: To install a memory card To connect a digital input / output device To connect an audio input / output device Perform the steps below to remove the camera module from the housing. 1. Using the bundled hex screwdriver, loosen the three (3) screws to
ACTi B94, www.acti.com Hardware Manual 43 Double-click on the camera model name, the default browser of the PC is automatically launched and the IP address of the target camera is already filled in the address bar of the browser. If you work with our cameras regularly, then there is even a better way to discover the cameras in the network – by using IP Utility. The IP Utility is a light software tool that can not only discover the cameras, but also list lots of valuable information, such as IP and MAC addresses, serial numbers, firmware versions,
ACTi B94, www.acti.com Hardware Manual 6 Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards. Do not use accessories not recommended by the manufacturer Only install this device in a dry place protected from weather Servicing Do not attempt to service this video product yourself. Refer all servicing to qualified service personnel. Damage Requiring service Disconnect this video product from
ACTi B94, www.acti.com Hardware Manual 38 4. Remove dome cover from the cover housing. 5. Remove the rubber from the dome cover. 6. Insert the rubber into the replacement dome cover. 7. Insert the replacement dome cover into the cover housing.
www.acti.com Hardware Manual 46 Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the same network segment, it is possible to use the Web browser of the PC to access the camera. You can use any of the browsers to access the camera, however, the full functionality is provided only for Microsoft In
ACTi B94, www.acti.com Hardware Manual 32 The table below shows the DI/DO connection specifications: Device DI Connection design TTL - compatible logic levels Voltage To trigger (low) Logic level 0: 0V ~ 0.4V Normal (high) Logic level 1: 3.1V ~ 30V Current 10mA ~ 100mA DO Connection design Transistor (Open Collector) Voltage & Current < 24V DC, < 50mA Typical Connection Based on these specifications, if the DI device has a voltage of 0V ~ 30V or the DO device has a voltage of < 24V (< 50mA), then the camera can supply internal power to these devices and there is no need to connect the DI/DO device to an external power so
www.acti.com Hardware Manual 28 2. Remove the plastic covering the dome cover. Final installation will look like the illustration below. Step 6: Connect to the Network Connect the other end of the network cable to a switch or injector. Then, connect the switch or injector to a network or PC and a power source. See Power-over-Ethernet (PoE) example connection di
ACTi B94, www.acti.com Hardware Manual 24 5. Insert the sealing insert and attach it at the end of the flex conduit. 6. Screw the conduit gland body to the conduit hole of the camera. Attach to Side Conduit Hole Attach to Bottom Conduit Hole 7. If the cable(s) will be routed along the surface, skip this step. If the cable will pass through the surface, do the following: a. Pull the network cable through the bottom conduit hole. or
ACTi B94, www.acti.com Hardware Manual 8 Package Contents Camera Mounting Screw Kit Hexagon Screwdriver Drill Template Conduit Gland Cable Gland Terminal Block (for Power) Terminal Block (for DI/DO and Audio In/Out) Quick Installation Guide Warranty Card Drill Template
ACTi TCM-7811 Security Camera Hardware user manual
TCM-7811 |
ACTi D61A Security Camera Hardware manual
D61A |
ACTi D61 Security Camera Hardware manual
D61 |
ACTi TCM-1231 Series Security Camera Hardware user manual
TCM-1231 Series |
ACTi TCM-5311 Security Camera Hardware user manual
TCM-5311 |
ACTi A92 Security Camera Hardware manual
A92 |
ACTi D71 Security Camera Manual manual
D71 |
ACTi TCM-5311 Security Camera Specifications
TCM-5311 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | HP | 336044-B21 | Quickspecs | hp/336044-b21-896.pdf | 12 Feb 2024 | 9 | |
2 | Danby | DAR340 | Owner's manual | danby/dar340-X3D.pdf | 05 May 2023 | 20 | 1.59 Mb |
3 | Tradewinds | RNC15 | Installation instructions manual | tradewinds/rnc15-8K6.pdf | 15 Jan 2023 | 18 | 0.96 Mb |
4 | MACROMEDIA | FLASH 8-USING FLASH VIDEO ENCODER | Using manual | macromedia/flash-8-using-flash-video-encoder-185.pdf | 25 Jul 2022 | 30 | |
5 | Philips | LC5331 | Declaration of conformity | philips/lc5331-6XZ.pdf | 24 Jan 2024 | 1 | 0.09 Mb |
6 | D-Link | 24-Port 10/100Mbps PoE Web Smart Switch with 4-Port 10/100/1000Base-T and 2-Port Combo SFP DES-1228P | Operation & user’s manual | d-link/24-port-10-100mbps-poe-web-smart-switch-with-4-port-10-100-1000base-t-and-2-port-combo-sfp-des-1228p-22S.pdf | 26 Aug 2022 | 100 | 2.81 Mb |
Infinova
V1700N Series IP Dome Operation Manual This manual mainly addresses the operation and programming of Infinova V1700N series IP domes. Based on network technology, V1700N series IP domes could easily realize network digital video transmission and network control function, and provide professional remote video services. They provide hi …
V1700N series(22 pages) |
Luda Farm
a) Connect the camera to power where it has good WiFi-connectivity. a) Open the app:b) Click OK to allow notications (Iphone only)c) In the app, press:d) Press ”Search”:1678 9102 3 4 5FULL WIFI CONNECTIONThe camera takes 45 seconds to startb) Download the FarmCam APP from Appstore/Google PlayFarmCama) Go to settings of your phone. Connect your phone t …
FarmCam IP2(2 pages) |
VSS Nederland
45.81/3” Sony Super HAD High/Standard-Resolution Color CCD600TVL Hi-Resolution, 350TVL Std-ResolutionBuilt-in 4mm F2.0 Fixed Lens- Option: 2.9mm, 6.0mmAuto Switching IR LED control by photocell- IR LED: 30pcsSmart IR : It prevents IR saturation2D-Digital Noise ReductionDead Pixel Compensation3-Axis Gimbal BracketPower: DC12V94.80Ø90Ø117Max. 90% RH VBS 1. …
SUPREME IMAGE VCD-328IR(2 pages) |
Q-See
Quick Installation Guide 4 Channel H.264 Compression DVR with Built-in Retractable 7” LCD Display Screen, (CIF) Real-Time Recording and 4 Color CCD Camera Kits MMOODDEELL QQRR44227744--441188
…
QR4274-418(9 pages) |
Overmax
Camspot 4.4Camspot 4.5User manual (addition) Dodatek do instrukcji obsługi1. WiFi confi guration2. Confi guration of sending pictures to e-mail/FTP after motion detection1. Konfi guracja WiFi2. Konfi guracja wysyłki zdjęć na adres email / FTP po wykryciu ruchu
…
Camspot 4.4(12 pages) |
FLIR
432-0004-31-12 Rev 100 Jan 2013HM-Series Quick Start GuidePower Button – The HM-Series camera has 3 power modes: On, Off, and Standby.• On - Takes approximately 90 seconds (during bootup there is a fast-flashing red LED on the eyepiece display).• Standby - After the camera is on, pressing the Power button will toggle the camera between On and Standby …
HM-Series(2 pages) |
Rosen Aviation Gateway MIP100 SeriesRosen Aviation Product User Manual: MIP100 Series PDF Technical manual - 962BMF MIP100 Series, 12 |
Autostart Remote Starter AS-1785 SHRemote Starter PDF Operation & user’s manual AS-1785 SH, 9 |
Frigidaire Refrigerator FRT18HP7JRefrigerator PDF Parts catalog FRT18HP7J, 11 |
RBI Boiler DOMINATOR Series#3Z2ZE9: DOMINATOR Series Boiler Manual DOMINATOR Series, 56 |
Intel Motherboard DG965MQMotherboard PDF Specification DG965MQ, 98 |
Honda Offroad Vehicle 2003 TRX250EX Sportrax 250EXHonda Offroad Vehicle Owner's manual (File: honda-2003-trx250ex-sportrax-250ex-owner-s-manual-211, 22.12.2023) 2003 TRX250EX Sportrax 250EX, 211 |
American Standard Plumbing Product Chandler 7048 SeriesAmerican Standard Chandler 7048 Series Plumbing Product Installation instructions Chandler 7048 Series, 4 |
Blanco Indoor Furnishing BLANCOMAGNUM 501-119-8Blanco BLANCOMAGNUM 501-119-8 User Guide (Doc Type: Indoor Furnishing Specifications) BLANCOMAGNUM 501-119-8, 1 |
Siemens Controller DXR2.E10PL-102BKController Installation instruction (Siemens DXR2.E10PL-102BK) DXR2.E10PL-102BK, 4 |
Lexmark All in One Printer X544DNLexmark Product Manual: X544DN PDF Manual - 69KMIH X544DN, 4 |
TomTom GPS GO 740 LIVEGPS #35M2EE GO 740 LIVE, 2 |
MCOHome Kitchen Appliances A8-9MCOHome Product Guide: A8-9 PDF Operation & user’s manual - 6152KA A8-9, 7 |