Manualios.com

Heli-Max Novus UH-1D HUEY Instruction Manual

Heli-Max Novus UH-1D HUEY Manual Online:

4.45, 1870 votes
Heli-Max Novus UH-1D HUEY User Manual
Heli-Max Novus UH-1D HUEY User Guide
Heli-Max Novus UH-1D HUEY Online Manual

Text of Heli-Max Novus UH-1D HUEY User Guide:

  • 26 PROGRAMMING YOUR TRANSMITTER PROGRAMMING YOUR TRANSMITTER The Heli-Max TX6024 transmitter is factory set for the Novus UH-1D Huey CX helicopter. Before making any changes it is recommended to fl y the model several times. If you feel a change is needed after several fl ights, then please feel free to make adjustments following the recommendations below. WARNING! Setting these values i

  • Heli-Max Novus UH-1D HUEY, 14 TRANSMITTER CONTROLS TRANSMITTER CONTROLS All controls are described with the tail pointing directly toward you. This is the best way to fl y in the beginning since it keeps the control inputs oriented the same direction. Once you start getting comfortable you can work on side hovering and nose-in. The dual rate switch provides dual control rates for the cyclic and tail rotor controls. Please use the low rate until you become accustomed to your Novus.

  • Heli-Max Novus UH-1D HUEY, 22 Replacing the Landing Gear Remove the four landing gear screws and carefully remove the landing gear. Route the battery lead through the new landing gear and place the landing gear back onto the helicopter. Install the four landing gear screws.

  • 20 MAINTENANCE AND REPAIR MAINTENANCE AND REPAIR The Heli-Max™ Novus UH-1D Huey CX is an extremely small helicopter. Working on a model this size will require small tools. The DTXR0170 DuraTrax® Precision Phillips Screwdriver 00x75mm is recommended. On occasion it will be necessary to replace damaged parts after a crash. Please use this section as a guide to perfor

  • Heli-Max Novus UH-1D HUEY, 2 IMPORTANT PRECAUTIONS IMPORTANT PRECAUTIONS ● Only use the included charger with the included battery or replacement part (GPMP0410). ● Do not attempt to use this charger with NiCd or NiMH battery packs. ● Never charge in excess of 4.20V per cell. ● If the battery should become damaged, discard it. Do not attempt to use a damaged battery. ● Do not leave the charger unattended while charging. Disconnect the battery and remove input power from the charger immediately if either becomes hot! However, it is normal for the charger to get warm. ● Disconnect the battery from the charger and carefu

  • Heli-Max Novus UH-1D HUEY, 27 Channel Reversing The channel reversing function is used to reverse the operation of a servo. Select the channel you want to reverse and press the [L] or [R] key and the direction indication on the screen will change. To set this value you must press the [ENTER] key before exiting this function. Aux Channel The AUX channel can be enabled or disabled by selecting the [ON] or [OFF] respectively. Buzzer Setting Set to [OFF] to disable the internal speaker. Set to [ON] to enable the internal speaker. 2 NOR REV NOR REV OFF ON STICK MOD ELEV AILE THRO RUDD AUX BUZZ Novus UH-1D Huey Default Settings

  • Heli-Max Novus UH-1D HUEY, 19 Landing Level the helicopter into a steady hover and slowly decrease power until the helicopter settles onto the ground. Basic Maneuvers Once you become comfortable with hovering at different orientations and landing, it’s time to move on to more advanced maneuvers. Slow Pirouettes – Add a small amount of tail rotor (left or right) and try rotating the helicopter slightly sideways and see if you can hold it there. If you feel uncomfortable, then bring the tail back toward you. Once you start getting comfortable, try moving the helicopter to the side. T

  • Heli-Max Novus UH-1D HUEY, 11 LITHIUM BATTERY HANDLING & USAGE LITHIUM BATTERY HANDLING & USAGE WARNING! Read the entire instruction sheet included with this battery. Failure to follow all instructions could cause permanent damage to the battery and its surroundings, and may cause bodily harm! ● Land your model immediately when the battery begins to lose power. Recharge the battery before attempting another fl ight. A dangerous situation can occur when attempting to recharge an over-discharged battery! ● ALWAYS charge the battery inside a fi reproof container placed in a fi reproof location clear of combustible materials. Failure to do so can result in property damage

  • Heli-Max Novus UH-1D HUEY, 15 Moving the cyclic stick right will cause the helicopter to tilt right and start moving that direction. Helicopter Moves Right Helicopter Moves RightHelicopter Moves Right Moving the cyclic stick left will cause the helicopter to tilt left and start moving that direction. Helicopter Moves Left Helicopter Moves LeftHelicopter Moves Left Moving the cyclic stick backwards (towards you) will cause the helicopter to tilt back- wards and start moving that direction. Helicopter Moves Backwards Helicopter Moves BackwardsHelicopter Moves Backwards

  • Heli-Max Novus UH-1D HUEY, 23 Replacing the Main Gear The Novus Huey uses an inner solid main shaft and a hollow outer main shaft. To access the main rotor gears it will be necessary to remove the landing gear fi rst. Remove the lower main gear retaining screw. The lower gear will simply drop down off the main shaft. If you need to replace the upper main gear, slide it down off the main shaft and reinstall the new gear, ensuring that the fl at spot molded inside the gear aligns with the main shaft. Reinstall the lower gear, ensuring that the screw aligns with the fl at spot machined on the inner main shaft. Replacing the Main Shaft The Novus CX uses an inner solid main shaft and a hollo

  • Heli-Max Novus UH-1D HUEY, 8 INSTALL THE TRANSMITTER BATTERIES INSTALL THE TRANSMITTER BATTERIES ❏ Open the battery cover on the back of the transmitter, remove the battery box and install eight AA batteries into the battery box. Double check the polarity of each battery before placing the battery box back into the transmitter and closing the battery cover. ❏ Turn on the transmitter and verify that the LCD initializes. Turn the transmitter off for now. If the LCD did not initialize, remove the battery box from the transmitter and verify that the batteries were installed correctly

  • Heli-Max Novus UH-1D HUEY, 6 ADDITIONAL ITEMS REQUIRED ADDITIONAL ITEMS REQUIRED ❏ (8) AA Alkaline cells (FUGP7308) KIT INSPECTION KIT INSPECTION Before starting assembly, take an inventory of the Novus UH-1D Huey CX to make sure it is complete, and inspect the parts to make sure they are of acceptable quality. If any parts are missing or are not of acceptable quality, or if you need assistance with assembly, contact Product Support. When reporting defective or missing parts, use the part names exactly as they are written in the Kit Contents list. Heli-Max Product Support Ph: (217) 398-8970, ext. 5 3002 N. Apollo Drive, Suite 1 Fax: (217) 398-7721 Champaign, IL 61822 E-mail: [email protected]

  • Heli-Max Novus UH-1D HUEY, 4 TABLE OF CONTENTS TABLE OF CONTENTS IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SAFETY PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ADDITIONAL ITEMS REQUIRED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 KIT INSPECTION. . . . . . . . . . . . . . . . . .

  • Heli-Max Novus UH-1D HUEY, 13 ❏ Your Novus helicopter uses a 2.4GHz system that requires linking the transmitter to the receiver when the unit is powered up. With the transmitter turned off, connect the fl ight battery to the helicopter. Then place the model on a fl at surface and turn the transmitter on. You will notice that the trim tab indicators are moving and the navigation lights on the helicopter remain solid. This is an indication of the linking process. Allow the helicopter to remain still and do not move the transmitter sticks during the linking process. ❏ Two loud tones will be emitted from the transmitter. Continue to allow the helicopter to remain still

  • Heli-Max Novus UH-1D HUEY, 12 TURNING THE MODEL ON TURNING THE MODEL ON ❏ Place the helicopter on its side and open the battery compartment door. Connect the fl ight battery and place the battery in the compartment as shown. ❏ Carefully place the extra wiring into the battery compartment and close the battery door. Place the helicopter onto a fl at surface and proceed to the next step.

  • Heli-Max Novus UH-1D HUEY, 28 E-BOARD ADJUSTMENTS E-BOARD ADJUSTMENTS Gyro Gain The gyro gain is used to adjust the amount of correction that the gyro applies to the tail rotor during unintended movements. Finding the ideal gain setting will take some experimentation. If the gyro is allowing the tail to drift, then raise the gain % and test fl y the model. If the tail is quickly oscillating (wagging), then lower the gain % and test fl y the model. Turning the adjustment clockwise increases the gain and turning the adjustment counter clockwise decreases the gain.

  • Heli-Max Novus UH-1D HUEY, 9 CHARGING THE FLIGHT BATTERY CHARGING THE FLIGHT BATTERY WARNING!! The charger supplied with the Heli-Max Novus Helicopter contains protective circuitry. If you experience any diffi culties while charging the battery, please disconnect the battery from the charger and unplug the charger from the power source. Allow the battery and charger to rest for two hours as this will allow the charge protection circuit to reset. If this issue re-occurs during normal use, please contact technical support for further assistance. ❏ Plug the wall transformer into an A

  • Heli-Max Novus UH-1D HUEY, Length: 8.27 in [210mm] Width: 1.93 in [49mm] Height: 4.80 in [122mm] Rotor Span: 7.68 in [195mm] Weight: 2.75 oz [78g] (with supplied fl ight battery) Specifi cations Entire Contents © 2010 Hobbico ® , Inc. HMXE0808 INSTRUCTION MANUAL Bell, UH-1D Huey, emblems, logos, and body designs are trademarks of Textron Innovations Inc. and are used under license by Hobbico®, Inc. ™

  • Heli-Max Novus UH-1D HUEY, 21 Main Rotor Grip Replacement Remove both blade bolts and main rotor blades. If working on the upper rotor, remove the fl ybar and linkage. The only way to remove the blade grip is to cut the grip on both sides as shown. Remove the two halves. Remove the two metal pivot pins from the head block. Slide the two metal pivot pins from the center of each grip into the blade grip. Press these pins in until they are fl ush. Align the new blade grip on the head block and from the outside of the grip. Push the pins into the head block. Install the fl ybar and main rotor blades. Replacing the Flybar Remove the fl ybar linkage from the blade grip. Pre

  • Heli-Max Novus UH-1D HUEY, 16 Moving the cyclic stick forward (away from you) will cause the helicopter to tilt forward and start moving that direction. Helicopter Moves Forward Helicopter Moves ForwardHelicopter Moves Forward Moving the collective stick up (away from you) will cause the helicopter to climb higher. Helicopter Climbs Helicopter ClimbsHelicopter Climbs Moving the collective stick down (towards you) will cause the helicopter to descend. Helicopter Descends Helicopter DescendsHelicopter Descends

  • Heli-Max Novus UH-1D HUEY, 18 FLYING FLYING The Heli-Max Novus UH-1D Huey CX is a lightweight helicopter. Taking that into consideration, you should only fl y indoors or in calm winds less than 1mph. The Novus should be fl own in a large area of at least 50 feet [15.25m] square with no obstacles. The Novus UH-1D Huey CX is lightweight and due to this it does not fl y well in ground effect (air disturbance when the model helicopter is hovered below 1 foot [30cm]). The model should be fl own at a minimum altitude of 1 foot [30c

  • 3 WARRANTY WARRANTY Heli-Max ™ guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty does not cover any component parts damaged by use or modifi cation. In no case shall Heli-Max’s liability exceed the original cost of the purchased kit. Further, Heli-Max reserves the right to change or modify thi

  • Heli-Max Novus UH-1D HUEY, 31 Part # Description 1 HMXE8297 Main Rotor Blades 2 HMXE8536 Flybar Assembly 3 HMXE8537 Main Blade Grips (2) 4 HMXE8458 Tail Rotor Blade 5 HMXE8574 Locking Sleeve Assembly 6 HMXE8573 Rotor Head Linkage Set 7 HMXE8539 Outer Main Shaft 8 HMXE8540 Inner Main Shaft 9 HMXE8541 Lower Head Block/Blade Drive 10 HMXE7417 Replacement Fuselage 11 HMXE8542 Swashplate Assembly 12 HMXE8040 Main Drive Gears Part # Description 13 HMXE7894 Swashplate Autorotation Frame 14 HMXE7895 Main Frame 15 HMXE7896 Landing Gear/Battery Mount 16 HMXE8835 Ball Bearing Set 17 H

  • Heli-Max Novus UH-1D HUEY, 10 ❏ Plug the battery into the charger. The charge indicator light will start fl ashing red quickly; this indicates that the battery is being charged. Once the battery is completely charged, the charge indicator light will turn green (solid or fl ashing). Disconnect the battery from the charger. Under normal operating conditions, the battery may take up to one hour to recharge. The battery is being charged. The battery is fully charged. A time-out has occurred. The battery voltage is too low or the charger is not powered. The charger is ready. Fast Flashing

  • 17 Moving the tail rotor stick towards the left will cause the helicopter nose to rotate left (counterclockwise). Nose Rotates Left Nose Rotates LeftNose Rotates Left Moving the tail rotor stick towards the right will cause the helicopter nose to rotate right (clockwise). Nose Rotates Right Nose Rotates RightNose Rotates Right

  • Heli-Max Novus UH-1D HUEY, 29 ORDERING PARTS ORDERING PARTS Replacement parts for the Heli-Max Novus UH-1D Huey CX are available using the order numbers in the Replacement Parts List that follows. The fastest, most economical service can be provided by your hobby dealer. To locate a hobby dealer, visit the Hobbico web site at www.hobbico.com. Choose “Where to Buy” at the bottom of the menu on the left side of the page. Follow the instructions provided on the page to locate a U.S., Canadian or International dealer. Parts may also be ordered directly from Hobby Services by calling (217) 398- 0007, or via facsimile at (217) 398-7721, but full retail prices and shipping and

Related Products and Documents (Toy):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Oster TSSTVDG01 Series Operation & user’s manual oster/tsstvdg01-series-O56.pdf 05 May 2023 24
2 Fujitsu AWYZ14LBC Operating manual fujitsu/awyz14lbc-58D.pdf 03 Feb 2023 26 1.64 Mb
3 Sony CLIE PEG-TH55 Spec sheet sony/clie-peg-th55-6N6.pdf 02 Nov 2022 2 0.61 Mb
4 Toshiba SDKP19 Specification sheet toshiba/sdkp19-4TX.pdf 27 Jan 2023 2 0.13 Mb
5 Alpine CDA9857 Owner's manual alpine/cda9857-S9E.pdf 23 Jul 2023 112 8.56 Mb
6 Whites Coinmaster classic III Instructions manual whites/coinmaster-classic-iii-A11.pdf 04 Dec 2023 27

Similar Resources:

  • Fisher-Price

    CHEVROLET SAWBLADE MONSTER TRUCK

    (36 pages)
    ®Please read this manual and save it with your original sales receipt.Tools needed for assembly: Short Shafted Phillips Screwdriver and Hammer (tools not included).Use only with a Power Wheels®12 Volt Lead-Acid Rechargeable Battery and a Power Wheels®12 Volt Charger with Type “12V” Connector (both included).Action Sounds Console requires three, alkali …
  • Eduard

    Lynx Mk.8 exterior

    (6 pages)
    detail set for 1/32 REVELL kit • sada detailů pro stavebnici 1/32 REVELL1/632 442REMOVEODSTRANITOPTIONVOLBAREPLACENAHRADITBENDOHNOUTGRINDOBROUSITSYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽDRILL HOLEVRTAT OTVORAPPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PRED SLEPENÍMCOLORED ETCHED PARTSLEPTANÉ BAREVNÉ DÍLYETCHED PARTSLEPTANÉ N …
  • Hangar 9

    Beast 100

    (70 pages)
    Wingspan.................................89.0 in (2,260mm)Overall Length ........ 87 in (2210mm) with spinnerWing Area .......................2,490 sq in (161 sq dm)Flying Weight ........................26–28 lb (12–13 kg)Engine Size ............................................ DA 100LAssembly mAnuAlBeast® 100Specifications …
  • Trends UK

    HEY DUGGEE HD21

    (3 pages)
    INSTRUCTION MANUALDUGGEESMART TABLET3+WARNING! All packing materials such as internal bags, plastic collars, plastic films and carton inserts are not part of this product and should be discarded for your child’s safety.Importantinformation • This toy is recommended for children aged 3 years and over• Please retain this manual for future refere …
  • Vollmer

    43697

    (12 pages)
    DE: Modellbauartikel, kein Spielzeug! Vor Gebrauch die Sicherheitshinweise und Anleitung genau lesen und beachten. Dieser Artikel ist ein Modellbauartikel für anspruchsvolle Modellbauer und Sammler. Aufgrund maßstabs- und vorbildgetreuer bzw. funktionsbedingter Gestaltung sind Spitzen, Kanten und filigrane Kleinteile enthalten. Für den Zusammenbau sind We …
  • Power Wheels

    N8417

    (32 pages)
    Please read this manual and save it with your original sales receipt. Tools needed for assembly: Phillips Screwdriver (not included); Assembly Tool (included). Use only with a Power Wheels® 12 Volt Lead Acid Rechargeable Battery with Built-in Thermal Fuse and Power Wheels®12 Volt Charger with Type 12V Connector (both included).Requires four "C" ( …

Comments, Questions and Opinions: