Manualios.com

Elenco Electronics rc snap rover Insruction Manual

Elenco Electronics rc snap rover Manual Online:

4.15, 1607 votes
Elenco Electronics rc snap rover User Manual
Elenco Electronics rc snap rover User Guide
Elenco Electronics rc snap rover Online Manual

Text of Elenco Electronics rc snap rover User Guide:

  • Elenco Electronics rc snap rover, -1- Basic Troubleshooting 1 Parts List 2 How to Use It 3 About Your Snap Circuits Parts 4 How It Works 5, 6 General Operating Instructions 6 DO’s and DON’Ts of Building Circuits 7 Advanced Troubleshooting 8 Project 1 9 Project 2 10 Projects 3, 4 11 Projects 5, 6 12 Projects 7, 8 13 Projects 9, 10 14 Projects 11, 12 15 Projects 13, 14 16 Projects 15, 16 17 Projects 17, 18 18 Project 19, 20 19 Projects 21-23 20 Other Snap Circuits ® Products 21 Bonus Projects B1-B3 22 WARNING: SHOCK HAZARD - Never connect Snap Circuits ® to the electrical outlets in y

  • Elenco Electronics rc snap rover, Project #3 OBJECTIVE: To make a rotating light. Lighthouse Build the circuit, place the base grid centered on the Rover body, and connect the jumper wires as shown. Place the Snap Rover ® in the middle of a dimly lit room and turn on the slide switch (S1). The light will shine around the room as Snap Rover ® spins. OBJECTIVE: To see if you can adapt to unusual controls. Backwards Rover Build the circuit shown and turn on the slide switch (S1). Turn on the remote control unit, extend the antenna, and use the levers try to drive the Rover around. The wiring has

  • Elenco Electronics rc snap rover, -10- Project #2 OBJECTIVE: To build a remote control vehicle. Remote Control Rover C h a n n e l s w i t c h o n r e m o t e c o n t r o l u n i t . Install six (6) “AA” batteries into the bottom of the Rover body and one 9V•battery into the remote control unit (batteries not included). Install the antenna into the remote control unit by screwing it in. Place the base grid on the Rover body; you may lock it into position by turning the hexagonal alignment posts (shown here), if desired. Build the circuit shown by placing all the parts with a black 1 next to them on the clear plastic base grid

  • Elenco Electronics rc snap rover, -16- Build the circuit shown and turn on the slide switch (S1). Turn on the remote control unit, extend the antenna, and press the left button. The LED (D4) turns on and off slowly. Project #13 OBJECTIVE: To build a remote control light. Slow R/C Flashlight OBJECTIVE: To show how capacitors store electrical charge. Capacitor BatteryProject #14 Build the circuit shown but leave the 100μF capacitor (C4N) unconnected. The orange and gray jumper wires are placed on the base grid at points C10 and E10. Touch the capacitor across the jumper wires at points C10-E10 to fill it with electricity. Now place it across

  • Elenco Electronics rc snap rover, General Operating Instructions -6- Wheel shaft Motor gear Spins 128 times faster than wheels How It Works (continued) Rover Drive Mechanism: The small gear on the Motor drives a larger gear, which drives a larger gear, which drives two larger gears (one on each side), which drive larger gears. The last, largest gears are fixed on shafts that are attached to the front and back wheels, making them move. Note that interlocking gears spin in opposite directions. Also notice that in the sets of interlocking ge

  • Elenco Electronics rc snap rover, -8- Advanced Troubleshooting (Adult supervision recommended) Elenco ® Electronics is not responsible for parts damaged due to incorrect wiring. If you suspect you have damaged parts, you can follow this procedure to systematically determine which ones need replacing: 1. Rover body and jumper wires: Flip the Rover body upside down and make sure the wheel mechanisms are clean. Install batteries in the Rover body and connect jumper wires to the Rover rear as shown; two wheels should move. Replace the orange and gray jumper wires with each of the other colors to see if any of the jumpers are damaged. If the wheels don’t move for any combination of wires, then the Rover body is d

  • Elenco Electronics rc snap rover, -20- Project #21 One-Way Light OBJECTIVE: To show how an LED works. Build the circuit, place the base grid centered on the Rover body, and connect the jumper wires as shown. When you close the slide switch (S1), electricity flows from the batteries through the switch (S1), the LED (D4), the resistor (R1), and back to the battery. The switch controls the electricity and the LED•(light emitting diode) converts electricity into light. The resistor limits how much electricity can flow - without it the batteries would overload the LED and damage it! LEDs are used in all types of el

  • Elenco Electronics rc snap rover, Note: If you have a more advanced model, there are additional part lists in the other project manuals. Important: If any parts are missing or damaged, DO NOT RETURN TO RETAILER. Call toll-free (800) 533-2441 or e-mail us at: [email protected]. Customer Service • 150 Carpenter Ave. • Wheeling, IL 60090 U.S.A. Qty. ID Name Symbol Part # Qty. ID Name Symbol Part # r 1 Rover Body 6SCRB r 2 100μF Capacitor (non-polarized) 6SCC4N r 1 r 1 Remote Control Unit Antenna 6SCTX1 6SCTX1A r 1 White LED 6SCD4 r 1 Base Grid (11.0” x 7.7”) 6SCBG r 1 100Ω Resistor 6SCR1 r 2 1-Snap Wire 6SC01 r 4 1KΩ Resistor 6SCR2 r 6 2-Snap Wire 6SC02 r 1 R/C Receiver 6SCRX1 r 2 3-Snap

  • (Part designs are subject to change without notice). Note: If you have a more advanced Model, there is additional information in your other project manual(s). The base grid functions like the printed circuit boards found in most electronic products. It is a platform for mounting parts and wires (though the wires are usually “printed” on the board). The blue snap wires are ju

  • Elenco ® Electronics, Inc. 150 Carpenter Avenue • Wheeling, IL 60090 (847) 541-3800 • Fax: (847) 520-0085 • Website: www.elenco.com • e-mail: [email protected] C4N C4N C1 D4 RX1 R1 R2 R2 R2 R2 S1 U8 Jumper Wires 2 x2 2 x2 2 x2 3 x2 W1 6 x1 7 x1 1 x1 4 x1 5 x1 1 x1 SCROV-10 Snap Rover ® Block Layout Important: If any parts are missing or damaged, DO NOT RETURN TO RET

  • Elenco Electronics rc snap rover, -13- Project #7 OBJECTIVE: To learn about Morse code. Build the circuit, connect the jumper wires, and turn on the slide switch (S1). Turn on the remote control unit and extend the antenna. Press the buttons on the remote control to generate long or short bursts of sound (from the W1 horn) or light (from the D4 LED). You can send secret messages to friends using Morse code, which uses a series of long and short bursts of sound or light to represent letters and numbers. A short burst is represented by a “•”, and a long burst by a “⎯”, as shown in this chart: Morse Co

  • Elenco Electronics rc snap rover, -15- Project #11 OBJECTIVE: To build a circuit with sound and light. Sound & Light OBJECTIVE: To show how capacitors store electrical charge. Electricity BankProject #12 Build the circuit, place the base grid centered on the Rover body, and connect the jumper wires as shown. Turn on the switch (S1) and electricity flows from the batteries through the circuit. The horn (W1) converts electricity into sound and the LED•(D4) converts electricity into light. The four 1KΩ resistors (R2) are connected in parallel, to act as a 250Ω resistance. Build the circuit and connect the

  • Elenco Electronics rc snap rover, -19- Project #19 OBJECTIVE: To show how water conducts electricity. Build the circuit at left and connect the jumper wires to it, but leave the loose ends of the green and yellow jumpers lying on the table initially. Turn on the slide switch (S1) - the LED (D4) will be dark because the air separating the jumpers has very high resistance. Touch the loose jumper ends to each other and the LED will be bright, because with a direct connection there is no resistance separating the jumpers. Now take the loose ends of the green and yellow jumpers and place them in a cup of water, without letting them touch each other. The LED should be lit, indicating you have detected water! For t

  • Elenco Electronics rc snap rover, -18- Build the circuit at left and connect the jumper wires to it, but leave the loose ends of the green and purple jumpers unconnected for now. There is one more part you need and you are going to draw it. Take a pencil (No. 2 lead is best but other types will also work). SHARPEN•IT, and fill in the shape below. You will get better results if you place a hard, flat surface directly beneath this page while you are drawing. Press hard (but don’t rip the paper), and fill in the shape several times to be sure you have a thick, even layer of pencil lead. Turn on the s

  • Copyright © 2008 by Elenco ® Electronics, Inc. All rights reserved. No part of this book shall be reproduced by REV-B Revised 2008 753131 any means; electronic, photocopying, or otherwise without written permission from the publisher.

  • -12- Rover Rear (upside down) Project #5 OBJECTIVE: To build a remote control vehicle with two sound levels. Two-Sound Rover Build the circuit shown and turn on the slide switch (S1). Turn on the remote control unit, extend the antenna, and use the levers try to drive the Rover around. Press the left or right buttons to activiate the horn (W1); press both for a louder sound. OBJE

  • Elenco Electronics rc snap rover, -5- Remote Control Transmitter: When the levers in the Remote Control Unit are pushed, electrical contacts are made connecting the 9V battery power to the transmitter, indicating which commands the user wants sent to the Rover. Forwards/Backwards commands for each set of wheels and two extra functions are controlled by different levers or buttons. Each of these use a different set of electrical contacts which encode a sequence of electrical pulses; the pulse sequence depends on which command(s) are being sent. The spacing between the sequences represents which channel setting (A-B-C) the remote control is on. This allows three units to use the same operating frequency in the sam

  • Elenco Electronics rc snap rover, -21- OTHER SNAP CIRCUITS ® PRODUCTS! FM Radio Model SCP-02 Motion Detector Model SCP-03 Music Box Model SCP-04 Space Battle Model SCP-05 Flying Saucer Model SCP-06 Contact Elenco ® to find out where you can purchase these products. Snap Circuits ® Jr. Model SC-100 Snap Circuits ® Model SC-300 Snap Circuits ® Pro Model SC-500 Snap Circuits ® Extreme Model SC-750 Musical Recorder Model SCP-01 Snap Circuits ® Mini Kits Build over 500 projects Including: • Digitally tuned FM radio • Adjustable light

  • Elenco Electronics rc snap rover, -9- The Snap Circuits ® Kit uses electronic blocks that snap onto a clear plastic base grid to build different circuits. These blocks have different colors and numbers on them so that you can easily identify them. Install six (6) “AA” batteries into the bottom of the Rover body and one 9V•battery into the remote control unit (batteries not included). Install the antenna into the remote control unit by screwing it in. Place the base grid on the Rover body; you may lock it into position by turning the hexagonal alignment posts (shown here), if desired. Build the circuit shown by placing all the

  • Elenco Electronics rc snap rover, -14- Project #9 OBJECTIVE: To show how capacitors slow things down. Build the circuit, place the base grid on the Rover body, and connect the jumper wires as shown. Turn the swtch (S1) on and the LED is on. Turn the switch off, and the LED•goes out slowly. Electricity stored in the 100μF capacitors (C4N) keeps the LED•on after the batteries have been disconnected. If you remove one of the capacitors then the LED will turn off faster, because you aren’t storing as much electricity. If you remove both capacitors, the LED will turn off immediately when the switch is turned off. Slow Turn-Off Project #10 OBJECTIVE: To compare types of circui

  • Elenco Electronics rc snap rover, -22- Project #B1 Machine Gun Rover Project #B2 Six Function R/C The remote control levers and buttons activate six functions: three LEDs (D1,•D2, &•D4), a horn (W1), a lamp, and a siren (U2 with SP). BONUS•CIRCUITS FOR•SNAP•CIRCUITS ® OWNERS If you own Snap Circuits ® Models SC-300, SC-500, or SC-750 (with 300+ experiments), then you may also build these circuits. Our website (www.snapcircuits.net) has additional circuits. DO•NOT•use parts from other Snap Circuits ® kits with your Snap Rover ® except in our approv

  • Elenco Electronics rc snap rover, -3- Install six “AA” batteries (not included) into the bottom of the Rover body and one 9V•battery (not included) into the remote control unit. Install the antenna into the remote control unit by screwing it in. The R/C Snap Rover Kit uses building blocks with snaps to build the different electrical and electronic circuits in the projects. Each block has a function: there are switch blocks, LED blocks, different length wire blocks, etc. These blocks are in different colors and have numbers on them so that you can easily identify them. The circuit you will build is shown in color and numbers, identifying the blocks that you will use and snap together to form a circuit. For Example:

Related Products and Documents (Video Game Controller):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 SHOWTEC Phantom 575 Pro EB Product manual showtec/phantom-575-pro-eb-25D.pdf 24 Mar 2024 29
2 Audio Note P2 SE Owner's information audio-note/p2-se-DSM.pdf 21 Jun 2022 11 0.3 Mb
3 Fujitsu ASYG09LZCA Installation/troubleshooting manual fujitsu/asyg09lzca-979.pdf 13 Sep 2022 60
4 Dymo MimioClassroom Operation & user’s manual dymo/mimioclassroom-77S.pdf 07 Mar 2023 112
5 Asus DSGC-DW - Motherboard - SSI EEB 3.61 Approved vendor list asus/dsgc-dw-motherboard-ssi-eeb-3-61-612.pdf 20 Dec 2023 1 0.03 Mb
6 Acer Aspire 7735ZG Manual  acer/aspire-7735zg-O6L.pdf 20 Nov 2022 13 1.33 Mb

Similar Resources:

  • Evil

    Master Mod

    (3 pages)
    Your Evil Controller comes with 20 customizable mod profiles. They operate just like classes in Call of Duty®. Simply select the mod profile (class) and assign mods (perks).By default, the first 10 mod profiles have a fire rate equal to that of their mod profile number. For example, mod profile 5 = 5 shots per second. Learn how to modify these default …
  • GameSir

    F3

    (10 pages)
    GameSir • Gaming is Winning.™© 2019 GameSir Inc. All rights reserved.Product may vary slightly from those pictures. Conductive AirFlash GripGameSir F3/F3 PlusUser Manual …
  • PDP

    AFTERGLOW AP.2

    (3 pages)
    AFTERGLOW® AP.2 For PlayStation®3For:PL-6422A Thank you for purchasing the AFTERGLOW® AP.2 Wireless for PlayStation®3! Contents: 1 AFTERGLOW® AP.2 for PlayStation®3. 1 AFTERGLOW® Wireless Link USB Adapter 1 USB Charge Cable 1 ManualUsing the AFTERGLOW® AP.2: 1) The AFTERGLOW® AP.2 is designed to work with the Sony PlayStation®3 video …
  • BASETech

    1388741

    (8 pages)
    Bestimmungsgemäße Verwendung …
  • Thrustmaster

    NASCAR PRO FORCE FEEDBACK 2

    (4 pages)
    QUICK INSTALLTHRUSTMASTER®US TECHNICAL FEATURES 1. Digital gearshift levers 2. POV button 3. Multi-function (4 in 1) button 4. Action buttons 5. Analog brake pedal 6. Analog gas pedal 7. Clamp screw 8. Pedal cable 9. USB connector F CARACTÉRISTIQUES TECHNIQUES 1. Leviers de changement de vitesse 2. Bouton POV (Point de vue) 3. Bouton 4 en 1 4 …
  • Hama

    THUNDER V5

    (34 pages)
    00051845/12.07 All listed brands are trademarks of the corresponding companies. Errors and omissions excepted, and subject to technical changes. Our general terms of delivery and payment are applied.Hama GmbH & Co KGD-86651 Monheim/Germanywww.hama.com …

Comments, Questions and Opinions: