Dexter Laundry T-300 VENDED Operator's Manual

Text of Dexter Laundry T-300 VENDED User Guide:

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 17 “Final Rinse” bath. If the customer does not meet the vend price of the “Extra Rinse” feature, the prompt will time out and the “Extra Rinse” bath will not occur. The figure below shows the sub menu options for Plus Cycle Options:

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 22 Control Menu: The Control menu allows for the user to observe important technical information for the control. No changes can be made at this menu. See below for detailed information on each sub menu. 1. “Serial Number”: This is the control serial number. 2. “MAC Address”: The MAC Address is a unique identifier designated to the control by the manufacturer. It allows the control to be recognized by network routers. 3. “IP Address”: The IP Address is the identifier given to the control by a network system. 4. “M Firmware”: The M Firmw

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 1 COMMERCIAL WASHER MODEL T-300 VENDED C-SERIES CONTROL OPERATOR’S MANUAL INSTALLATION & OPERATION INSTRUCTIONS Please read this information and retain for reference. WARNING - THIS WASHER IS EQUIPPED WITH DEVICES AND FEATURES RELATING TO ITS SAFE OPERATION. TO AVOID INJURY OR ELECTRICAL SHOCK, DO NOT PERFORM ANY SERVICING UNLESS QUALIFIED TO DO SO. IT IS THE RESPONSIBILITY OF THE OWNER TO CHECK THIS EQUIPMENT ON A FREQUENT BASIS TO ASSURE ITS SAFE OPERATION. A

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 28 DRIVE OV VFD Over- voltage Fault Condition This error is over-voltage on the VF drive Delay Delay time is 35 seconds. Action Stop the machine and clear the cycle. Keep the door locked until the machine has stopped moving and then unlock the door. Solution Step 1: Measure the supply voltage to the VFD on the L1, L2 (or N), and L3 (if connected to three phrase power). The supply voltage should be from 187 to 264 VAC or 108 to 132 VAC for a 120 VAC VFD. Also make sure the supply wires on L1, L2 (or N) and L3 (if connected to three phase p

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 11 When manual programming mode is entered, the “Start”, “Hot”, “Warm” and “Cold” buttons perform alternate functions. Button Name Alternate Function in Programming Mode Start Becomes the action to accept the displayed option or the “Enter” key Hot Becomes the action to move UP through displayed options (Press & hold for accelerated scrolling) Warm Becomes the action to move DOWN through displayed options (Press & hold for accelerated scrolling) Cold Become

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 29 DRIVE GFI VFD Ground Fault Condition This error is a ground fault interruption on the VF drive Delay Delay time is 12 seconds. Action Stop the machine and clear the cycle. Keep the door locked until the machine has stopped moving and then unlock the door. Solution Check VFD light code before turning off power. Check the wiring connections to the drive and motor. Check the ground wiring of the drive, motor and incoming connection to ensure a proper ground is present. Check for damaged motor wires. DRIVE

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 2 TABLE OF CONTENTS Page No. Washer Specifications 2 Mounting Dimensions 3 Installation Instructions 4 Operating Instructions 8 Programming the Washer Control 10 Displayed Washer Faults 24 Servicing and Troubleshooting 30 Accessories and Contact Information 34 WASHER SPECIFICATIONS MODEL T-300 20 LB. WASHER CAPACITY CYLINDER SIZE ELECTRICAL DRIVE SYSTEM WASH SPEED INTERMEDIATE EXTRACT FINAL EXTRACT MACHINE CONTROL WATER INLET DRAIN VALVE 20 LBS/2.7 CUBIC FT. (9.1 kg/76.5L) 21” DIA X 13 1/2” DEEP (53cm X 34cm) 208-240 VAC, 60 HZ, 1

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 30 SERVICING AND TROUBLESHOOTING CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. ATTENTION. Lors des opérations d'entretien des commandes, étiqueter tous les fils avant de les déconnecter. Toute erreur de câblage peut être une source de danger et de panne. If any of the following symptoms occur on this washer, check the suggested remedies listed below.

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 24 DISPLAYED WASHER FAULTS Displayed Fault Code Description DOOR LOCK ERROR Door Lock Error Condition This error is when the Door Locked signal is not received within one second after the start of the cycle. A fter three attempts to start the washer. Delay Immediate Action When the error occurs, the Door Lock Motor will be turned off; all other outputs will be turned off. Solution Check VFD fault light. Check to hear if door motor engaged. Turn off the power to the washer. Check wire connections to door /lock switches. Check wire connections from switches to controller. Check P-4 Door/Lock wire connections

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 13 Prices Option: This option allows the user to set values for coin acceptor inputs and to set the vend price. It also allows the user to return the values to factory defaults. After changing prices using the “Up” or “Down” buttons, the “Enter” button must be pressed again for the control to store the changes that have been made. 1. “RIGHT COIN” and “LEFT COIN” are the two possible inputs from coin acceptors. 2. “SET VEND” is the actual Base Vend Price (or Vend Price A) that is shown on the control display. To reset either the coin acceptor

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 16 Plus Cycle Options: The “Plus Cycle” options allow for the user to prompt the customer for varying vend prices based on additional wash baths chosen. In general, the user can program the additional wash baths in a similar manner to what was described in the “Cycles” Options section. It also allows the user to return the programmable values to the factory default setting. No plus cycle options are active using the factory default. To reset all values in the Plus Cycles option to factory default, press “Enter” when the “DEFAULT” prompt is shown. Press “Enter” again when th

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 8 OPERATING INSTRUCTIONS - STARTING THE WASHER A. Load the clothes into the cylinder and latch the door securely. Be sure clothing does not get caught between the door gasket and tub front when closing the door. Maximum load is 20 pounds clothes, dry weight. Do not load the washer with more than 20 lbs. B. Select the appropriate cycle temperatures for the load being washed. C. Add low sudsing powdered detergent into the “detergent” compartment of the automatic dispenser on the top of the washer. If desired add fabric softener to the “fabric softener” compartment. Use the amount of fabric s

• 8514-223-001 REV B page 33 IMPORTANT TRANSIENT VOLTAGE SURGE SUPPRESSORS Like most electrical equipment your new machine can be damaged or have its life shortened by voltage surges due to lightning strikes which are not covered by factory warranty. Local power distribution problems also can be detrimental to the life of electrical components. We recommend

• 8514-223-001 REV B page 10 PROGRAMMING THE WASHER CONTROL The washer control can be programmed to prompt the user for alternate vend prices, change washer cycle times, temperatures and many other options. This can be accomplished in two ways: 1. Manual programming utilizing the “Start”, “Hot”, “Warm” and “Cold” buttons 2. USB download of a cu

• 8514-223-001 REV B page 12 Quick Test Option: When the Quick Test Option is chosen, the washer will begin a shortened wash cycle without the displayed vend price being met. The purpose of this shortened cycle is to test all major components for proper operation. Error Codes should all function normally during this test. The display will show customer prompts in a similar way t

• 8514-223-001 REV B page 23 COIN WASHER DEFAULT CYCLE The following table shows the complete details for the coin washer default cycle. Bath Bath Cycle Time (min.) Water Temp. Delay Fill Spin Time (min.) Prewash 0 Cold Off 0 Wash 9 Warm Off 0 Extend Wash 0 n/a n/a n/a Rinse 4 Cold Off 1 Final Rinse 5 Cold Off n/a Extra Rinse Spin n/a n/a n/a 0 Extra

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 20 Usage Menu: The Usage menu allows for the user to track data about machine usage. See below for detailed information on each sub menu option. 1. “Coin Audit”: The coin audit field shows the accumulation of coin pulses that were sent to the control over each of the left and right coin inputs. Note that this is a count of coin pulses, not an accumulated report of vend value. a. The user can also return the coin audit amounts to the factory default setting (zero

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 4 INSTALLATION INSTRUCTIONS All washers must be installed in accordance with all local, state and national building, electrical, plumbing and other codes in effect in the area. WARNING - THESE INSTALLATION AND SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED PERSONNEL ONLY. TO AVOID INJURY AND ELECTRICAL SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS, UNLESS QUALIFIED. FOUNDATION REQUIREMENTS This machine is designed for use on or over bare concrete floor - not to be used above combu

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 32 Water does not flush softener compartment. Water Valve Coil Check coil continuity at terminals and replace if no continuity. Water Inlet Screens Check water inlet screens for blockage and clean if necessary. Water Check to insure that water is turned on and operating. Pressure Switch Check pressure switch continuity between terminal contacts. If no continuity, check pressure switch hose for obstruction. If the hose is okay then change pressure switch. Water level too high Pressure Switch Check for blockage in pr

• 8514-223-001 REV B page 9 EMERGENCY STOP / SAFETY DOOR LOCK This machine is equipped with a Safety Door Lock that locks the door closed from when the cycle is started until the cycle is complete. The door lock prevents opening the door for up to 3 minutes if the power is interrupted during the cycle. The Emergency Stop button pauses the washer

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 26 COMM ERROR5 VFD Communication Fault Condition This error is a data error on communications between the controller and the VF drive Delay Delay time is 12 seconds. Action Stop the machine and clear the cycle. Keep the door locked until the machine has stopped moving and then unlock the door. Solution The CE errors are communications errors. Data Cable noise can cause the majority of these errors. Check VFD fault light before turning off power. Check the data cable between the controller and the drive. Replace data cable if it appears damaged and fault appears again. P

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 19 press the “Enter” button to move to the minutes. Once the hours and minute are both chosen, the “Enter” button must be held down for 3 seconds to confirm that RTC is meant to be reset to the complete entry. 7. “Date”- Similar to “Time”, if a problem occurs and the RTC date is not accurate, it can be reset to the current date using this option. a. The day of the month in “DATE” can be set by using the “Up” or “Down” buttons to change the number that is flashing. Once the desired day of the month is chosen, press the “Enter” button to move to the month of the year. Once

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 31 Door will not open Thermoactuator Check to see if thermoactuator and its mechanism are stuck or binding and not allowing the door lock motor to open. Check to be sure that the locking thermoactuator is not receiving 120VAC during the last 1 1/2 minutes of the cycle. Also check to see that the unlocking thermoactuator is receiving 120VAC during the last minute of the cycle. If the thermoactuators do not receive voltage at the correct times, change the PCB relay board. If the timing and voltage are correct, replace the thermoactuator. Door Locking Motor Check the door lock motor. Make sure the motor is not stuck or in a bind. If mot

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 7 FUSING REQUIREMENTS: SINGLE-PHASE 115VAC MODELS - 20 AMP TIME-DELAY (DUAL ELEMENT) FUSE (or equivalent circuit breaker) SINGLE- and THREE -PHASE 208-240VAC MODELS - 15 AMP TIME-DELAY (DUAL ELEMENT) FUSE (or equivalent circuit breaker) CONTROLS TRANSFORMER (208-240V models only) The controls transformer is located inside the control trough and steps a range of 208 to 240 volts down to 115 volts. There are two terminals on the controls transformer for the primary (incoming) power. Use the terminal marked “208V” for power supplies between 208 and 219 volts. Use the terminal marked “240V” for power supplies between

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 25 Condition Invalid washer size jumper (harness) configuration. COMM ERROR2 Wrong Washer Size Jumper Configuration Delay Immediate (after the wrong size jumper configuration is read). Washer size/type inputs are read only at power up, before starting a cycle, once every 24 hours, and in factory test mode. Action Stop the washer. Solution Check VFD fault light before turning off power. If the controller was installed in a different size machine before being installed in this machine, a problem can occur.

• Dexter Laundry T-300 VENDED, 8514-223-001 REV B page 6 PLUMBING Water supply hoses are furnished with each machine. The threaded connections on the hoses are ¾-11 ½ NHT. Separate hot and cold water lines must be provided, maintaining 30 psi to 120 psi (207 kPa to 827 kPa) water flow pressure. A 140F (60C) degree hot water supply is recommended for best washing results. Do not exceed 180F (82C) degree water temperature. DRAIN The drain outlet tube at the rear of the machine is 2 ¼ inches (57 mm) in diameter. Any drain hose used must be lower than the drain valve to assure proper draining. ELECTRICAL WARNING SHUT OFF POWER AND WATER BEFORE OPENING ANY SERVICE PANE

More Instructions:

	Dexter Laundry T-300 VENDED Parts & service manual 14-09-2022 87	DOWNLOAD
	Dexter Laundry T-300 VENDED Operator's manual 06-04-2024 66	DOWNLOAD
	Dexter Laundry T-300 VENDED Parts & service manual 23-12-2023 77	DOWNLOAD
	Dexter Laundry T-300 VENDED Operator's manual 17-08-2022 68	DOWNLOAD

Related Products and Documents (Washer):

Comparable Devices:

Similar Resources:

• Frigidaire FTF5000HS0 (16 pages) InstallationInstructionsFull Size Tumble Action Washers| m mNotice d installationMachine a laver par culbutageinstrucciones para ia instalaci6nLavadora de acci6n giratoria de tamale grandem m __For your safetythe information in this manual must befollowed to minimizethe risk of fire or explosion or to prevent property damage, personal injury or lossof life.- …

• Samsung WA13V9 (24 pages) :DVKLQJ0DFKLQHXVHUPDQXDOLPDJLQHWKHSRVVLELOLWLHV7KDQN\RXIRUSXUFKDVLQJD6DPVXQJSURGXFW7RUHFHLYHDPRUHFRPSOHWHVHUYLFHSOHDVHUHJLVWHU\RXUSURGXFWDWZZZVDPVXQJFRPJOREDOUHJLVWHU:$9:$9:$9:$99#8-+%%A'0KPFF  …

• Malmet WDS (53 pages) Malmet (Australia) Pty Ltd Head Office & Customer Service 9-11 McKay Avenue PO Box 373 LEETON NSW 2705 Phone: (02) 6953 7677 Email: [email protected] ISSUE 5 Page 1 15/03/2016 ABN 95 001 717 791 WDS Washer Disinfector Sanitizer Operation, Maintenance and Installation Manual Serial Number: .... …

• Indesit IWB 70852 C ECO HK (16 pages) 1 0716 本文為翻譯本，所有內文以英文為準。生產商保留任何改善本機功能的權利。本機或任何附件會因技術和商業上需要作出更改，恕不另行通知。前置式洗衣機Front Loading Washer IWB 70852 C ECO HK Instructions & Installation Manual 安裝及使用手冊 …

• Whirlpool WFW5090JW0 (36 pages) W11330506BW11330507B – SPIf you have any problems or questions, visit us at www.whirlpool.com. Pour tout problème ou toute question, consulter www.whirlpool.ca.Designed to use only HE High Efficiency detergents.Conçue pour l’utilisation d’un détergent haute efficacité seulement.Para obtener acceso al Manual de uso y cuidado en español, o pa …

• LG T1666NEFTC/01 (124 pages) www.lg.comOWNER’S MANUALCopyright © 2019 LG Electronics Inc. All Rights ReservedMFL68780969Rev.01_052319WASHING MACHINEBefore beginning installation, read these instructions carefully. This will simplify installation and ensure that the product is installed correctly and safely. Leave these instructions near the product after installation for future refer …

Comments, Questions and Opinions: