Airsight XX60A Operation & User’s Manual

Text of Airsight XX60A User Guide:

• 9 Figure 1.9 2.1.1 .1 Basic Properties There is some device information in the Basic Properties, such as Device ID, System Firmware Version, and Web UI Version.（Figure 2.0). The Device ID is the camera’s MAC ID, which should be the same as shown on the sticker on the bottom of the camera. Every camera has a unique MAC ID. So if there are many IP addresses show

• Airsight XX60A, 46 If it shows the following errors when you click Test. Please check that the information you filled in is correct and try again. 1) Cannot connect to the server. 2) Network Error. Please try later. 3) Server Error. 4) Incorrect user or password. 5) The sender is denied by the server. Maybe the server needs to authenticate the user, please check and try again. 6) The receiver is denied by the server. Maybe because of the anti-spam privacy of the server. 7) The message is denied by the server. Maybe because of the anti-spam privacy of the server. 8) The server does not support the authentication mode used by the device. Report Internet IP by Mail: If selected, you will receive e-mails that

• Airsight XX60A, 11 2.1.1.3 Upgrade Firmware Enter the correct User and Password to upgrade system Firmware and Web UI. Please upgrade system firmware first and then upgrade Web UI or it may damage the camera.（Figure 2.3). Figure 2.3 Please download the firmware package for the correct type of your camera before you upgrade. Follow the upgrade document carefully to upgrade. Please see readme file first before you upgrade. CAUTION: You should not upgrade the firmware unnecessarily. It is possible to damage the camera if a mistake is

• Airsight XX60A, 22 Mode: This mode is optional, 50HZ/60HZ for the users who use 50HZ/60HZ frequency, outdoor for users who want to use the camera to monitor towards an outdoor environment. NOTE: The camera should be used in an indoor environment (unless protected from the elements). Bright: Set the parameters to adjust the image quality of the video. Click to adjust the value. Contrast: Set the parameters to adjust the image quality of the video. Click to adjust the value. Default all: Click it to set all the parameters back to the factory setting. NOTE: If

• Airsight XX60A, 4 1.3 Product Views 1.3.1 Front View Figure 1.1 1 Wireless Antenna: WI-FI Antenna (rotate to vertical position as shown above). 2 Housing: Alloy waterproof housing. 3 Infrared LEDs: 66 infrared LEDs with 8-15 meter night vision. 4 LENS: CMOS sensor with fixed zoom lens. . 1.3.2 Cable Interface Figure 1.2 Audio Output: The jack is used to connect an external speaker or audio output device. Audio Input: The jack is used to connect an external microphone or audio input device. I/O Alarm Pin: 1 Alarm input (GND) 2 Input 3 Output A 4 Output B. Network Interface: RJ-45/10-100 base T. Network Light: The green LED will be on when the network is connected, the yellow LED will blink when

• Airsight XX60A, 37 This is the most important step. You need to set port forwarding in your router, to refer to the IP of your camera correctly, for DDNS to work. There are so many kinds of routers, so it’s difficult to show fixed steps, but here are some samples of different router’s port forwarding settings, just for reference: TP-LINK: 1. Login to the router. 2. Choose “Forwarding”, select “Virtual Servers” 3. Click the Add New button, pop-up below: Figure 7.5 Fill in the service port (don’t use 80), IP address of the camer

• Airsight XX60A, 3 1. INTRODUCTION This is an integrated wireless IP Camera solution. It combines a high quality digital Video Camera with network connectivity and a powerful web server to bring clear pictures to your Desktop from anywhere on your local network or over the Internet. The main function of the camera is to transmit remote video over IP network. The high quality video image can be transmitted with 30fps speed on the LAN/WAN by using MJPEG hardware compression technology. It is based on the TCP/IP standard, build-in WEB server which supports Internet Explorer. Therefore the management and maintenance of your camera becomes simple by using the network to achieve the remote configurat

• 55 4. APPENDIX 4.1 Frequently Asked Questions Note: For most problems you might encounter, please check Network connections first. Check the working status revealed by the indicators on the network server, hub, exchange and network card. If abnormal, check the network connections. 4.1.1 I have forgotten the administrator username and/or password. To reset the administrator username and password,

• Airsight XX60A, 28 Click Live Video and then select to see four channels, or to see nine channels. In this case, you can see all the cameras from a remote position by internet, for example, if you are on a business trip, you can use the first camera’s (Host camera) DDNS to view all the devices via the internet. Figure 5.3 3.1.3 Upgrade Device Firmware If you want to upgrade the camera, please upgrade Device Firmware first, then upgrade Web UI. Click Browse and choose correct bin file, then click Submit to do upgrading. NOTE: Before doing an upgrade via Browser, please make sure the IP Camera Tool of your computer could find the camera’s IP. Attention: Please keep the power

• Airsight XX60A, 49 3.18.2 Motion Detect Sensitivity You can choose level 1-10; level 10 means the most sensitive, 1 means the least sensitive. Figure 9.9 3.18.3 Alarm Input Armed / IO Linkage on Alarm If you want to connect external alarm devices, when it’s an alarm input device, choose Alarm Input Armed to enable it, when it’s an output device, choose IO Linkage on Alarm to enable it. Figure 10.0 There are two options for Trigger Level. (Figure 10.1). High: When the external alarm device is close, then the alarm is triggered. Low: W

• Airsight XX60A, 21 Figure 4.1 Audio Video Settings   Figure 4.2 Audio buffer: Click this icon, it will show five numbers, which means 1/2/3/4/5 seconds buffer of audio. Reversal: Click this icon to reverse (flip) the image. Click again to go back to normal. Mirror: Click this icon to see a mirror image. Click again to go back to normal. NOTE: You can choose Reversal and Mirror function when you set up the camera in a special position (upside down for example). Mode, Bright, Contrast Settings  Figure 4.3

• Airsight XX60A, 41 3.10 Date &Time Settings Set the date and time for your camera. Choose the Clock Time zone of your country. You can choose Sync with NTP Server (Figure 8.3) or Sync with PC Time (Figure 8.4). Figure 8.3 Figure 8.4 3.11 Users Settings Eight accounts are acceptable for this system. Here you can set the user names and password as Administrator, Operator or Visitor, with permission for them as below:  Visitor: In this mode, you can only view. (Details 2.7).  Operator: You can control the direction of IP Camera and set some parameters. (Details 2.8).

• Airsight XX60A, 7 Figure 1.7 After this is done, the icon “IP Camera Tool” will be displayed on your desktop. CAUTION: Before installing and using the product, please read the following precautions carefully and make sure they are fully understood. Use only the power adaptor included with the product. Use of an unauthorized power adapter may cause damage to your IP Camera. Do not touch the lens of the IP Camera. The optimum focus range has been set for you. If you turn the lens, it may cause incorrect focus and blurry images. Do not turn the Pan/Tilt mechanism by force, it may cause damage to

• Airsight XX60A, 18 Status of Channels: There are 9 icons at the bottom of the UI which show the status of each channel of the camera. Grey color, means there is no device connected to the main device for this channel. Green color, means the device is connected for this channel, and it works well. Red color, means the device for this channel is recording. Yellow color, means this channel is set in multi-device already, but it fails to connect to the main device. OSD Settings:   Figure 3.6 OSD: Means “On-Screen Display”, click “Audio video” > “OSD”, set display date

• 43 Figure 8.7 Set the pilot lamp mode, to one of the following three options: (1) Non-connected network out: Blinks while connected to the internet and turn off when disconnected. (2) Non-connected network with more slow-frequency flicker: Blinks while connect to the internet and more slower when disconnected. (3) Extinguished: Stays OFF. 3.14 Backup & Restore Figure 8.8 1 ） Backu

• 19 Figure 3.7 Rate and Resolution: Rate: Set video frame here, from “full-speed to 1fp/5s”. (Figure 3.8). Resolution: Set the resolution to be 160*120/VGA (640*480)/QVGA (320*240). (Figure 3.9). NOTE: When doing recording, Rate and Resolution parameter settings is very helpful for getting smaller sized record files, lower the parameter to get a smaller file. Figure 3.8 Figu

• Airsight XX60A, 8 2. SOFTWARE OPERATION 2.1 IP Camera Tool When the Device has been mounted properly, you can double-click the Icon “IP Camera Tool” and a dialog box shown in Figure 1.8 will pop up. Figure 1.8 Note: The software searches IP Servers automatically over your LAN. There are 3 cases: 1. No IP Cameras found within LAN. After about 1 minute search, the Result Field will show “not found IP Server” and the program shut down automatically. 2. IP Cameras have been installed within LAN. All the IP Cameras will be listed and the total number is displayed in the result field as shown in Figure 1.8. 3. The IP Cameras installed within LAN do not share the same subnet with the monitorin

• Airsight XX60A, 13 (2) “Server Push Mode”: available in Firefox, Safari, and Google Chrome browser. (3) “Sign in mobile phone”: available in Mobile phone. 2.3 For IE Browser Choose ActiveX Mode (For IE Browser), and sign in. Figure 2.7 Figure 2.8 The first time you login to the camera, you might get an ActiveX prompt as in the picture above, please click the prompt and choose Run Add-on, refresh and login to the camera again, then will see live video, as below.

• Airsight XX60A, 33 Figure 6.5 3.5 ADSL Settings When connected to the Internet through ADSL directly, you can enter the ADSL username And password obtained from ISP.  Figure 6.7 3.6 UPnP Settings Click UPnP Settings to choose Using UPnP to Map Port:

• Airsight XX60A, 12 2.To access the camera by IE Browser directly, just type the camera’s IP address, for example, if the camera’s IP address is 192.168.1.123: Figure 2.4 Figure 2.5 The default user name is admin, no password (leave blank). Input the correct user name and password, the Sign In interface will pop-up. There are three models to login (figure 2.6). Figure 2.6 (1) Active Mode (For IE Browser): available in IE 6.0 or above.

• Airsight XX60A, 50 Figure 10.1 There are two options for Output Level. (Figure 10.2). High: When chosen, the IO Pins work as a switch that is closed. Low: When chosen, the IO Pins work as a switch that is switching off. Figure 10.2 3.18.4 IO Pins for IO Alarm Linkage Figure 10.3 I/O PINS: 1 Alarm input 2 Alarm input 3 Alarm output 4 Alarm output Input pins: The input pins can be used for 1-way external sensor input. For example, you may connect a Passive Infrared (PIR) Sensor to it for motion detection. When the external sensor is triggered, the IP camera can be programmed to send an e-mail with a picture or to control the internal relay output. If you link an external al

• Airsight XX60A, 2 CONTENTS 1. INTRODUCTION.......................................................................................................................................................... 3 1.1 FEATURES...............................................................................................................................................................................................3 1.2 PACKING LIST..............................................................................................................................................

• Airsight XX60A, 15 Figure 3.1 Click OK and restart the browser. You can also click “Start” menu->“Internet Explorer”, and choose “Internet attributes”, or via “Control Panel” ->“Internet Explorer”, to access Security settings. NOTE: Make sure that your firewall or anti-virus software doesn’t block the software or ActiveX. If you couldn’t see live video, please close your firewall or anti-virus software, and try again. If you allowed the ActiveX to run, but still cannot not see live video, only a Red Cross in the center of the video, and the device status light changed to yellow color not green, please change to another port

• Airsight XX60A, 42 Figure 8.5 3.12 Pan/Tilt/Zoom (PTZ) Settings Figure 8.6 1. Go center on boot: The camera rotates to the center automatically when it starts. 2. PT speed: Set Pan/Tilt speed. 3. Upward patrol speed: Set the speed of cruising upward. 4. Downward patrol speed: Set the speed of cruising downward. 5. Leftward patrol speed: Set the speed of cruising leftward. 6. Rightward patrol speed: Set the speed of cruising rightward. NOTE: Value 0 means the fastest, value 10 means the slowest. In order to protect the camera’s motor, we recommend that setting the speed to value 5. 3.13 Indicator Settings

Related Products and Documents (Security Camera):

Comparable Devices:

Similar Resources:

• Panasonic BB-HCM527 (2 pages) Important InformationNetwork Camera (PoE Ready)Model No.BB-HCM527BB-HCM547Indoor Use OnlyOutdoor Ready© Panasonic System Networks Co., Ltd. 2008PQQX16404XA KK0808CM2120 (CE)How to Use the DocumentationThis manual is written for both the BB-HCM527 (Indoor Use Only) and the BB-HCM547(Outdoor Ready). Available features and operations vary slightly depending …

• Bosch FLEXIDOME AN micro 1000 (2 pages) Vídeo | FLEXIDOME AN micro 1000FLEXIDOME AN micro 1000 www.boschsecurity.es Esta cámara minidomo es una cámara de videovigi-lancia analógica lista para usar. El sensor de altorendimiento, 960H y CCD de 1/4 pulgadas propor-ciona una resolución de 720 líneas de TV. La cáma-ra representa una solución perfecta para los entor-nos con condiciones adversas …

• BURG-WACHTER SUNTEC SNC-4302 (2 pages) Kurzanleitung / Quick installation guide SNC-4302 Version 1.0sfi/0312/dt-engl/A5 KURZANLEITUNG IP-Kamera SNC-4302 Um die IP-Kuppelkamera in Betrieb zu nehmen, gehen Sie bitte wie folgt vor: 1. Installieren Sie die Kamera an der gewünschten Stelle. Element Definition Beschreibung 1 Reset Zurücksetzen auf Werkseinstellungen. 2 Objektiv Drehen Sie das O …

• Orion GST-2050 (2 pages) HD-SDI 3-AXIS DAY & NIGHTIR DOME CAMERAGST-2050MANUAL◐ HOW TO INSTALL1. Opening the dome2. Removing the dome3. Camera installation:::Pushing the latch button.(Remove the protectionsheet after installing.)Lift the dome. When you push the latchbutton, it is unlocked and you can lift the dome.(1) Fix the camera set with the supplied screws on ceiling or w …

• Santec SCC-10KEIF (20 pages) Version 1.0sfi/1214/dt-engl/A5 BEDIENUNGSANLEITUNG / USER MANUAL DEUTSCH / ENGLISH HD-CVI Mini-Kuppelkamera mit IR-LEDs HD-CVI mini dome camera with IR LEDs Modell / Model: SCC-10KEIF VTC-432IRHWD …

• Sensormatic VM96 (4 pages) Quick Reference Guide VM96 VERSION 5 QUICK REFERENCE GUIDE (8000-0848-05, REV. B) 1 of 4 Using View Manager® 96 Version 5 A B C D Ac tvt y Photo On Off VC R Clear Entry Menu Close Open Lock Mon Cam Prev Next Ac k Help 1 2 3 4 5 6 7 8 9 0 Vi ew Patrn Zone Seq Hold Unless otherwise noted use your TOUCH TRACKER to perform these tasks. Select a Monitor 1. En …

Comments, Questions and Opinions: