Digital Monitoring Products XTL Series Operation & User’s Manual
|
Digital Monitoring Products XTL Series, System Setup XTL Series User’s Guide 31 User # User Name Level* Temp Code Temp Days Areas Arm Only HOW TO FILL IN THIS TABLE User # - TheUserNumberof the person authorized to use the system. Level* - Master or Standard authority. Temp Code-Isthiscodeset to expire? Temp Days - The number of days a temporary user has authority to use the system. Areas-Whatareasdoesthis user have the authority to arm and disarm? Arm Only - Is this user restricted to just arming? Refer to the User Codes section of this User’s Guide for additional information. Y N 1 2 3 4 5 6 Y N Y N 1
Digital Monitoring Products XTL Series, Arming and Disarming XTL Series User’s Guide 13 Arming a Home/Away System 1. Enter your user code. The keypad displays HOME AWAY or HOME SLEEP AWAY(youmayhavethreeareas). 2. Select HOME to arm the Perimeter only. 3. Select SLEEP to arm the Perimeter and Interior. 4. Select AWAY toarmthePerimeter,Interior,andBedroom. 5. The system displays any faulted and bypassed zones in the following order: faulted burglary zones, bypassed burglary zones,faulted24-hourzones,andbypassed24-hourzones. 6. At this point you can force arm or bypass any faulted burglary zones. A zone that is force armed is res
© 2013 Digital Monitoring Products, Inc. Information furnished by DMP is believed to be accurate and reliable. This information is subject to change without notice. Silencing an Alarm When the alarm siren is sounding, enter your user code or present your card to a keypad during the Status List display. All/Perimeter or Home/Sleep/Away System IS THIS A FALSE
Digital Monitoring Products XTL Series, 22 XTL Series User’s Guide User Menu Using the Zone Monitor Function 1. Access the User Menu. 2. PresstheCOMMANDkeyuntilZONE MONITOR? displays. 3. Press any Select key. The keypad displays PERIM ALL NBR. 4. Select PERIM to place all disarmed perimeter zones into Zone Monitor. 4a. The keypad displays PERIM? ADD RMV. 4b. Select ADD to add all perimeter zones to Zone Monitor. 4c. Select RMV to remove all perimeter zones. 5. Select ALL to place all disarmed zones into Zone Monitor. 5a. The keypad displays ALL? ADD RMV. 5b. Select ADD to add all disarmed zones to Zone
User Menu XTL Series User’s Guide 19 User Check-in User Code Level: Master or Standard. Function: This feature allows you to monitor the arrival of children from school or employees to work by having a special Check-in Report sent to your email address or cell phone if programmed. Appendix D describes the Email/Cell Phone option. Sending a Chec
Arming and Disarming XTL Series User’s Guide 15 6. The system displays any faulted and bypassed zones in the following order: faulted burglary zones, bypassed burglary zones,faulted24-hourzones,andbypassed24-hourzones. 7. At this point you can force arm or bypass any faulted burglary zones. A zone that is force armed is restored into the system if it later returns
Digital Monitoring Products XTL Series, Arming and Disarming XTL Series User’s Guide 17 Arming Function System Operation: Home/Sleep/Away, or All/Perimeter. You can use theArming shortcut keys, 1, 3, 6, and 7 when the systemisdisarmed.Youmaybepromptedtoenteryourusercode. If any zones are faulted, select force arm or bypass. Refer to the Arming Section for detailed arming operation. Home/Sleep/Away Arming Arm Home — Press 3 for 2 seconds to arm the perimeter. Arm Sleep — Press 7 for 2 seconds to arm the perimeter and interior areas and leave the bedroom area off. This shortcut key is ava
Digital Monitoring Products XTL Series, 6 XTL Series User’s Guide Introduction ALARM CANCELLED An Alarm signal just sent to the central station was cancelled because a user code was entered after the alarm was sent. Also, an Alarm Cancel signal is sent to the Central Station. ALARM VERIFIED Avalidburglaralarmhasoccurredandhasbeenmanuallyveried bytheuser.ThealarmsystemalsotransmitsaVERIFYmessageto the Central Station. ENTER CODE The system requires you to enter a personal user code. User codes can be used for turning your system
Digital Monitoring Products XTL Series, 8 XTL Series User’s Guide Introduction Instant Zone Exterior windows and non-entry doors, or interior protection devices, are typically not programmed with delay times. If these zones fault while the system is armed, an alarm occurs instantly. 24-Hour Zone A24-hourzoneisnotturnedonoroffbyarmingordisarmingyour system. Some examples of 24-hour zones are re zones, panic zones, and temperature control zones. Areas An area is made up of burglary zones that can be armed or disarmed together. The Perimeter area, for exa
Digital Monitoring Products XTL Series, Appendix C XTL Series User’s Guide 37 ARMING AND DISARMING AN AREA SYSTEM PressCOMMAND,thekeypaddisplaysARM DISARM?. Press the Select key under either option. The keypad displays ENTER CODE: -. Present your card to the keypad logo. Once the system validates the card, all areas accessible by you arm or disarm automatically. ENTRY DELAY All Systems - Once the protected door is opened and the entry delay starts, the keypad displays ENTER CODE:
Digital Monitoring Products XTL Series, 26 XTL Series User’s Guide User Menu Permanent Schedules User Code Level: Master only. 1. Access the User Menu. 2. PresstheCOMMANDkeyuntilSCHEDULES? displays. Press any Select key. The keypad displays PRM EXT. Select PRM. 3. The keypad next displays the day of the week you want the schedule to start as SUN MON TUE WED. Press the COMMANDkeytoshowtheremainingdaysoftheweekand then Select the start day. 4. The keypad displays OPENING TIME?.Press
Digital Monitoring Products XTL Series, Cut along dotted lines. Cut along dotted lines. Text For this action OFF(Outputnameor#) TurnstheOutputspeciedtoOFF MOMENTARY(Outputnameor#) TurnstheOutputspeciedtoMOMENTARY Z-WAVEHELP ListofZ-Wavecompatibletextcommands STAUS LIGHTS To receive a status update for all light devices TURNON(Lightname) TurnsthespeciedlighttoON TURNON(Lightname)(Dimmerlevel) Turnsdimmerlightontoaspecictemp TURNOFF(Lightname) Turnsthespecie
User Menu XTL Series User’s Guide 21 Bypass Zones User Code Level: Master or Standard. Function: Allows you to bypass a zone prior to arming the system. Bypassingisusuallydonewhenazonecannotberestoredtonormal andyouwanttoarmthesystem.Oncebypassed,thesystemdoes not respond to any activity on the zone
Cut along dotted lines. MyAccess™ Text Messaging Quick Commands PanelPhoneNumber:________________________ AreaNames: 1. ________________________ 2. _________________________ 3. ________________________ 4. _________________________ 5. ________________________ 6. _________________________ OutputNames: 1. ________________________ 2. __________
Digital Monitoring Products XTL Series, 40 XTL Series User’s Guide Appendix D MyAccess™ Text Messaging Commands For use with the XTL and XTLC only Yoursystemmaybeprogrammedtoallowsimpletextmessagesto be sent to the security system and perform basic user operations. Bytextingamessagefromyourcellphone,thefollowingactions can be performed:Arm/Disarm, CancelAlarm, turn Outputs On/ Off,checkArmedStatus,Turnonandofflights,Lock andunlock doors, and Set the thermostat. The user that is texting commands to the system must have the authority t
Digital Monitoring Products XTL Series, Appendix D XTL Series User’s Guide 39 Appendix D Email/Cell Phone Message User’s Guide YourXTLSeriessecuritysystem’sreportingcapabilitycanbeused tosendreportstoanemailaddressorcellphonenumber(XTLand XTLConly)inmuchthesamewayassomeonesendingyouanemail woulddo.You canreceive reportsofalarms,troubles,orsystem armings and disarmings and know at a glance your
Digital Monitoring Products XTL Series, 32 XTL Series User’s Guide Appendix A Appendix A About the Display Events Section User Code Level: Master or Standard. WhileintheDisplayEventsfunction,usetheCOMMANDandBack Arrow keys to move forward or backward through the list of events. To view more information about each display, press the Select key as directed in the explanations below. Using the Display Events Function 1. Access the User Menu. 2. Press the COMMAND key until DISPLAY
Digital Monitoring Products XTL Series, 34 XTL Series User’s Guide Appendix A Supervisory Event Displays This displays the automatic test report date and time. Description MSG 11:58P 10/17 AUTO RECALL The test report was sent to the central station at the date and time shown. System Monitor Event Displays This displays any problems with the system AC power or battery. Description TBL 11:41A 10/17 AC POWER An AC failure occurred at 11:41 AM onOctober17. SystemMonitorEventTypes-Therearetwoeventtypes: TBL - Trouble RST - Restore SystemMonitorEventNames
16 XTL Series User’s Guide Arming and Disarming Disarming an Area System 1. PresstheCOMMANDkeyuntilARM DISARM displays. During entry delay this process starts at step 3 below. 2. Select DISARM to disarm areas. 3. The keypad displays ENTER CODE: . Enter your user code andpressCOMMAND.ThekeypaddisplaysALL? NO YES. 4.
Digital Monitoring Products XTL Series, Arming and Disarming XTL Series User’s Guide 9 Arming and Disarming How Your System Operates Your system has been programmed to operate in one of three modes: Area, All/Perimeter or Home/Sleep/Away. • All/Perimeter — Your burglary protection is divided into two areas: Interior and Perimeter. Perimeter arming is for when you are staying inside but want the comfort of knowing the exterior doors and windows are armed. Perimeter arming allows you to move freely about inside
Digital Monitoring Products XTL Series, Appendix D XTL Series User’s Guide 43 Common Keypad Displays Listed below are several keypad messages you may see on the display. Follow the instructions in the Possible Solutions column to correct the problem. In many cases, you need to call a service person to correct the problem. Displays not discussed here indicate your service representative should be called. Message Tone at Keypad Meaning Possible Solutions INVALID CODE No The user code you entered is not recognized by the system. Check the user code and try again. CLOSING TIME Yes The schedule has expired but the system has not been armed. Users still on the premises are
Digital Monitoring Products XTL Series, 20 XTL Series User’s Guide User Menu Sensor Reset User Code Level: Master or Standard. Function: Clears Fire and Supervisory zone alarms and trouble keypad displays. Sensor Reset also clears low battery displays from wireless sensors that have restored. Make sure all smoke is cleared from around the area of the smoke detectors before performing a Sensor Reset to prevent the alarm from occurring again. Resetting the Sensors 1. Access the User Menu. 2. When SENSOR RESET? displays, press any Select key. The keypad displays SENSORS OFFforvesecondsfollowedby SENSORS ON. 3. The ke
Digital Monitoring Products XTL Series, 2 XTL Series User’s Guide Practice your escape plans Devising an escape plan is only the beginning. For the plan to be effective everyone should practice escape routes from each room. Second Floor Building Front Building Back First Floor Fire Escape Window Ladder Figure 1: Sample Escape Route Map Early detection The best way to survive a re or other emergency isto get out early. A re alarm system installation, with smoke and carbon monoxide detectors in each room, can greatly decrease your risk of loss or injury. Emergency Evacuation Plans Overview The National Fire
Digital Monitoring Products XTL Series, XTL Series User’s Guide i XTL Series User’s Guide Table of Contents Section Page Section Page Introduction ..............................................................1 XTL, XTLN, XTLN-WiFi, and XTLC Systems ........................1 About Your Security System .............................................1 Emergency Evacuation Plans ............................................ 2 Keypads .........................................................................3 Special Keypad Tones ......................
Digital Monitoring Products XTL Series, 42 XTL Series User’s Guide Appendix D Check Armed Status Text Command Allows you to check the system armed status. If armed, the system will send a message stating the type of system you have followed by ON,suchasALLSYSTEMONorHOMESYSTEMON.Ifdisarmedandno openzones,thesystemwillsendSYSTEMREADY.Ifdisarmedwith openzones,itwillsendSYSTEMNOTREADYfollowedbyanyopen zones.AmessageofACPOWERTROUBLEwillindicatewhenapower failureoccurs.I
Digital Monitoring Products XTL Series, 12 XTL Series User’s Guide Arming and Disarming installation to send a report of the system disarming to the central sta tion. Z-Wave Lock Disarming:IfyoursystemisinstalledwithaZ-Wave compatible lock, a valid user code entered at the lock will unlock the door and disarm the system. Disarming an All/Perimeter System 1. During the entry delay time, the keypad displays ENTER CODE:. Enter your user code. 2. The keypad displays any zones that went into alarm and any communication
Digital Monitoring Products XTL Series, 24 XTL Series User’s Guide User Menu Select YES to restrict this user to arming only. TheArmOnlyusercodecanbypasszonesnotinanormal condition at the time of arming. 10. After you complete your selections, the keypad displays USER # ADDED. 11.PresstheBackArrowkeyoncetoaddanotheruserortwice to exit the User Menu. Changing User codes User Code Level: Master only. 1. Access the User Menu. 2. PresstheCOMMANDkeyuntilUSER CODES? displays. 3. Press any Select key. The
Digital Monitoring Products XTL Series, 10 XTL Series User’s Guide Arming and Disarming Exit Delay: The keypad then displays the exit delay time as it counts down. If the entire system has been armed, your system beeps the exitdelaytoneateight-secondintervalsuntilthelast10seconds whenthekeypadbeepsatthree-secondintervals.Afterexitingthe building,ifyoure-enterduringthecountdowntheexitcountdown restarts, allowing additional time to then disarm or again exit the building during the countdown. This restart can occur only one time. When the exit delay time ex pires,
Digital Monitoring Products XR100FC Security System Operation & user’s manual
XR100FC |
Digital Monitoring Products XR150 Security System Operation & user’s manual
XR150 |
Digital Monitoring Products Canadian XR100 Security System Operation & user’s manual
Canadian XR100 |
Digital Monitoring Products Canadain XR500 Security System Programming manual
Canadain XR500 |
THOMSON Thombox Security System Quick installation manual
Thombox |
Digital Monitoring Products Graphic Touchscreen Security System Operation & user’s manual
Graphic Touchscreen |
Digital Monitoring Products 1912XR Security System Installation manual
1912XR |
DSC Power 832 Security System Installation instructions
Power 832 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | HP | 995C Series | Function manual | hp/995c-series-Z4K.pdf | 24 Sep 2023 | 82 | |
2 | CDA | PC870 | Installation, use and maintenance manual | cda/pc870-787.pdf | 27 Dec 2023 | 32 | |
3 | Philips | EasyStar FC8802 | Operation & user’s manual | philips/easystar-fc8802-D67.pdf | 04 Jun 2023 | 8 | |
4 | Niles | IntelliControl ICS DMS4 | Operation & user’s manual | niles/intellicontrol-ics-dms4-6PZ.pdf | 05 Aug 2022 | 50 | |
5 | Tripp Lite | SU1500XLCD | Owner's manual | tripp-lite/su1500xlcd-R54.pdf | 08 Nov 2023 | 96 | 35.1 Mb |
6 | Sharp | R-3A53 | Service manual | sharp/r-3a53-3RJ.pdf | 05 Dec 2023 | 47 | 5.38 Mb |
Potter
MFG. #5406080 - REV B9/11PRINTED IN USA PAGE 1 OF 2RA-6075RLCD ANNUNCIATOR INSTALLATIONPotter Electric Signal Company, LLC • St. Louis, MO • Cust Service: 866-956-1211 • Tech Support: 866-240-1870 • Canada: 888-882-1833 • www.pottersignal.comInstall in accordance with installation manual, #5403594.DescriptionThe RA-6075R is a LCD remote annunciator …
RA-6075R(2 pages) |
MOFLASH SIGNALLING
7.0 Cable GlandThe X450 and LED450 beacons are supplied as standard with 1 x M20 threaded side cable entry with provision for up to 4 supplied to special order.SAFETY WARNINGIf the X450 and LED450 are used at high ambient temperatures, ie over +400C then the cable entry temperature may exceed +700C and therefore suitable heat resisting cable glands must be u …
X450 Series(2 pages) |
Bosch
Bosch Digital Video Recorders DVR1A DVR1C DVR4C Divar Divar MR Divar XF DiBos Micro DiBos RackmountSystemOperating System Embedded Embedded Embedded Embedded Embedded Embedded Windows XP Embedded Windows XP EmbeddedRack Mountable No No No Yes Yes Yes Yes YesSDK Available No No No Yes No Yes Yes YesWarranty 3 Years 3 Years 3 Years 3 Years 3 Years 3 Years 3 Ye …
DVR1A(2 pages) |
Viking
• Vandal Resistant Features: 14 gauge, louvered, stainless steel faceplate with stainless steel speaker/mic screen, heavy duty metal keypad and “Call” button• Optional EnhancedWeather Protection (EWP) • Yellow “in use” LED• Volume adjustments for microphone and speaker• Advanced call progress detection: disconnects on busy signal, ret …
K-1700-3(4 pages) |
Digimerge
PACKAGE CONTENTS:ATTENTION: • * Channel/ Port configuration and HDD (hard disk drive) capacity may vary by model. Check your package for specific content information.• Monitor and Cameras are not included.• Ethernet Cable, Broadband Router and Computer are required for local and remote monitoring (not included).• For detailed setup and software …
DH200(2 pages) |
Philio Technology Corporation
PSR07 Smart Color ButtonThis device is a multiple functions button switch. It is able toswitch the appliances on/off or adjust the percentage of dimmer.It can also work as a timer. The well designed wall bracket andmagnetic back let the switch can be fixed on the wall. This productcan be included and operated in any Z-WaveTM network wit …
PSR07(6 pages) |
HP Computer Accessories USB Media Docking StationHP USB Media Docking Station User Guide (Maintenance and service manual), @X58MX5 USB Media Docking Station, 70 |
Husqvarna Lawn Mower YTH1542XPPDF Guide (@3978DS), Husqvarna YTH1542XP Lawn Mower (21st Jan 2024) YTH1542XP, 44 |
Boss Audio Systems Car Receiver MP3-3195RPDF Manual (@X683L5), Boss Audio Systems MP3-3195R Car Receiver (Monday 25-09-2023) MP3-3195R, 17 |
QUAN SHENG Two-Way Radio TG-007PDF Manual (@2J888S), QUAN SHENG TG-007 Two-Way Radio (04.09.2023) TG-007, 35 |
Ilsintech Welding System Keyman S1Ilsintech Welding System Keyman S1 Instruction manual Keyman S1, 90 |
Christie Projector LX380Christie Projector Specifications (File: christie-lx380-specifications-2, Wed 09.2023) LX380, 2 |
Electro-Voice Portable Speakers Sb120a#IK69PY Sb120a: Electro-Voice Portable Speakers Owner Documentation Sb120a, 4 |
Kenwood Car Video System KVC-1000KVC-1000 (Car Video System ePDF User Manual, #4AOUM9) KVC-1000, 36 |
Dimplex Indoor Fireplace EF3003-230EF3003-230 (Indoor Fireplace ePDF User Guide, #PXN176) EF3003-230, 16 |
Sears Refrigerator Kenmore 461.95882Sears Product Manual: Kenmore 461.95882 PDF Use & care manual - X6E997 Kenmore 461.95882, 21 |
Skil Measuring Instruments ME981901#ABX38L: ME981901 Measuring Instruments Owner's manual ME981901, 100 |
Sony Monitor XVM-R70 - MonitorMonitor Product manual (Sony XVM-R70 - Monitor) XVM-R70 - Monitor, 3 |