Manualios.com

Graphtech SK200-09 Operation & User’s Manual

Graphtech SK200-09 Manual Online:

3.65, 2338 votes
Graphtech SK200-09 User Manual
Graphtech SK200-09 User Guide
Graphtech SK200-09 Online Manual

Text of Graphtech SK200-09 User Guide:

  • Graphtech SK200-09, 2-9 2.6 Checking the Interface Connection For Windows XP. (1) Launch the Control Panel using the [Start] menu on the Windows desktop. (2) The screen shown below is displayed when you click on the “Printers and Other Hardware” icon. (3) The screen shown below is displayed when you click on the “Scanners and Cameras” icon. Check that “Graphtec SK200-09” is displayed here.

  • III CONTENTS TO ENSURE SAFE AND CORRECT USE ................................................................................... i Safety Precautions ..................................................................................................................... ii Installation Precautions .......................................................................

  • Graphtech SK200-09, 4-2 4.2 Cleaning the Feed Rollers (1) Turn off the scanner. (2) Open the top cover as described in Section 4.1, “Opening and Closing the Top Cover”. (3) While rotating the feed rollers, wipe them clean using a soft cloth that has been moistened with water or a neutral detergent (diluted with water) and firmly wrung out. Feed rollers (4) Wipe the feed rollers once again using a soft, dry cloth to remove all the moisture. (5) Close the top cover as described in Section 4.1, “Opening and Closing the Top Cover”. Caution •Take care not to get your fingers caught in

  • Graphtech SK200-09, 4-9 (5) Calibration ends after approximately 10 minutes. Click the [OK] button to complete calibration. (6) To check the calibration results, click the [Confirm] button in the Calibration screen (shown in step (2) above). (7) The following prompt is displayed. Insert the calibration sheet into the scanner once again as instructed. (8) Click the [OK] button to start scanning. The scanned data is displayed when scanning is complete. Colors may differ slightly for individual sensors to make it easier to identify problem areas in calibration. This does not indicate a defect. Check that there are no vertical streaks, such as white patches, in the scanned data

  • Graphtech SK200-09, 3-2 3.2 Loading a Document How to use the document guides Insert the document (the surface to be scanned) face up into the scanner until the top edge of the document contacts the feed rollers. At this time, make sure that the document is straight and that it is centered in the scanner. (1) With the top cover in the closed status, turn on the scanner’s power supply. (2) Move the document guides to the left and right until they are adjusted to the document width. (3) Place the document between the document guides, and then in

  • Graphtech SK200-09, 4-4 4.4 Cleaning the Image Sensors (Transparent Contact Plates) The scanner’s image quality drops when the transparent contact plates over the image sensors become dirty, so clean the image sensors whenever necessary. (1) Turn off the scanner. (2) Open the top cover as described in Section 4.1, “Opening and Closing the Top Cover”. (3) As shown below, wipe off any soiled areas on the transparent contact plates using a soft cloth that has been moistened with water or a neutral detergent (diluted with water) and firmly wrung out. Transparent contact plates (4) Wipe the transparent contact plates once again using a soft, dry cloth to remove a

  • Graphtech SK200-09, 4-1 CHAPTER 4 DAILY MAINTENANCE 4.1 Opening and Closing the Top Cover Opening the top cover (1) Turn off the scanner. (2) Push the left and right open levers on the top cover in the upward direction to unlock them, and then open the cover fully (approximately 60 degrees). (3) When the cover is fully open, lower it slightly to engage the top cover fixing stay that holds the top cover in place. 2 1 Closing the top cover (1) Raise the top cover slightly from its open status to disengage the top cover fixing stay, and then close the cover gently. (2) Check that the left and right levers on the top cover are locked. 2 1 Caution Take care not to get you

  • 2-4 2.4 Connecting the Scanner to a Computer USB Connection A USB cable is used to connect the scanner to the computer, via the respective USB interface connectors. The connectors at the computer and scanner ends of the USB cable have different shapes. Make sure that the cable is oriented correctly before making the connection. Make sure that both the scanner a

  • Graphtech SK200-09, I-1 INDX A Adobe Acrobat Reade ................................. 1-1 Anti-curling guides............................... 1-1, 1-2 Anti-curling guides, Attaching ...................... 1-5 B BEFORE USING THE SCANNER .............. 1-1 C Calibration ................................................... 4-8 Calibration sheets ....................................... 1-1 Carrier sheet, Using .................................... 3-4 Cleaning paper ............................................ 1-1 Color correction .

  • Graphtech SK200-09, v Caution When disconnecting the power cable, be sure to hold on to the plug, and not pull on the cable itself. • Pulling on the cable will expose the core wires, or cause damage such as broken wires. Current leakage from the exposed or damaged areas may result in a fire hazard or electric shock. Before cleaning the scanner, be sure to unplug the power cable from the power outlet. • Failure to do so may result in electric shock. Do not allow dust or metallic matter to adhere to the power plug. • If the power plug becomes dirty, thoroughly wipe it clean. • The use of a dirty powe

  • Graphtech SK200-09, IV CHAPTER 4 DAILY MAINTENANCE...................................................... 4-1 4.1 Opening and Closing the Top Cover ..........................................................................4-1 4.2 Cleaning the Feed Rollers ........................................................................................... 4-2 4.3 Cleaning the Gap Rollers ............................................................................................4-3 4.4 Cleaning the Image Sensors (Transparent Contact Plates) ..................................... 4-4 4.5 C

  • Graphtech SK200-09, vii Caution Take care not to drop metallic items such as paper clips or staples, or spill water, other fluids or flammable solvents (alcohol, benzene, thinner, etc.) inside the scanner. • Metallic items or fluids coming into contact with the internal electrical components may result in a fire hazard or electric shock. If such items or fluids fall or are spilled inside the scanner, immediately turn off the power, remove the power plug from the power outlet and either contact the store where you purchased your scanner or your nearest Graphtec representa

  • Graphtech SK200-09, 2-5 2.5 Installing the Driver Software C heckpoint The procedure outlined below is based on the requirement that you are logged on to Windows with administrator rights. Consult your Windows XP or Windows 2000 manual for more information. For Windows XP (1) Use the USB cable to connect the scanner to the computer, and then turn on the computer. (2) When Windows starts up, insert the CD-ROM supplied with the scanner into the CD- ROM drive. The “Start” screen opens automatically. Click the [Quit] button to close the “Start�

  • Graphtech SK200-09, 5-1 CHAPTER 5 TROUBLESHOOTING PROCEDURES If the scanner seems to be operating abnormally, perform the troubleshooting procedures described in this chapter before requesting a service call. 5.1 The scanner Is turned on but doesn’t operate at all 5.2 The scanner operates improperly after connection to the computer 5.3 The control panel’s red ERROR LED is lit Cause The power cable has come loose. The scanner is connected to a power outlet that does not provide the rated power supply or supply voltage. The power outlet is not supplying a supply voltage. Remedy Insert the power plug firmly.

  • 503-10 Shinano-cho, Totsuka-ku, Yokohama 244-8503, Japan Tel : +81 (045) 825-6250 Fax : +81 (045) 825-6396 Email : [email protected] Web : www.graphteccorp.com Printed in Japan

  • Graphtech SK200-09, A-1 APPENDIX Appendix A Options and Consumables Optional and consumable items can be obtained from the store where you purchased your scanner or your nearest Graphtec representative. Options Consumables Part no. Item name IS0907 Carrier sheet (A0) IS0908 Carrier sheet (A1) IS0917 Calibration sheet EM-CP Cleaning paper (50 sheets) Part no. Item name ST0064 High stand

  • Graphtech SK200-09, 2-2 2.2 Turning the Power On and Off The LED (blue) on the [POWER] button changes as follows to indicate the scanner’s power supply status. • Unlit: The scanner is turned off. • Lit: Lights when the scanner is turned on and remains lit while it is operating normally. • Flashing: Flashes when the scanner is in power-saving mode. Turning the Power On Press the [POWER] button on the scanner’s control panel. When the scanner is in the power-on status, the [POWER] button lights blue. ON Turning the Power Off Press

  • Graphtech SK200-09, I INTRODUCTION Thank you for choosing the Graphtec SK200-09 Image Scanner. Please read this manual thoroughly before attempting to use your new product to ensure that you use it safely and correctly. Notes on this Manual (1) No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, without the prior written permission of Graphtec Corporation. (2) The product specifications and other information in this manual are subject to change without notice. (3) While every effort has been made to provide complete and accurate information, please conta

  • Graphtech SK200-09, 2-7 For Windows 2000 (1) Use the USB cable to connect the scanner to the computer, and then turn on the computer. (2) When Windows starts up, insert the CD-ROM supplied with the scanner into the CD- ROM drive. (3) Turn on the power to the scanner. (4) The screen shown below appears. Click [Next] to move to the “Install Hardware Device Drivers” screen. (5) When this screen is displayed, select the option “Search for a suitable driver for my device (recommended)” and then click [Next] to display the “Locate Driver Files” screen. (6) When this screen is displayed, select the check box entitled “Specify a location” and click [

  • Graphtech SK200-09, 4-7 4.7 Scanner Calibration Calibrate the scanner if scanning quality is observed to deteriorate, with scanned results such as those described below • The scanned image is distorted • Areas of uneven color appear in the scanned image • Other unsatisfactory results (but excluding problems related to media quality, such as folds, creases, or paper curl) Preparation and checks Recommended usage environment Monitor: 1024 x 768 pixels, High Color or better resolution C heckpoint A low-resolution monitor will make

  • Graphtech SK200-09, 1-3 (10) EJECT key .................. Press this key to feed the document. If this key is pressed when the scanner is in document-loaded status, the document-loaded status is canceled and the document is ejected to the front of the scanner. If this key is pressed after the scanning operation has been canceled or after scanning of the document was halted partway through the scanning operation, the document-loaded status is canceled and the document is ejected to the rear of the scanner. (11) STOP key .................... Compulsorily stops scanning of the document. If the ERROR LED flashes when the top cover is in the closed status, press this key to suspend the scanning o

  • i TO ENSURE SAFE AND CORRECT USE •To ensure the safe and correct use of your Image Scanner, read this manual thoroughly prior to use. • After reading this manual, store it in a safe place for reference as necessary. • Do not allow small children to touch the Image Scanner. • The following describes important points for safe operation. Be sure to observe them strictly.

  • ix WARNING Only computers or peripherals (computer input/output devices, terminals, printers, etc.) certified as complying with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules, may be attached to this product when this product is operated in a residential environment. Operation with non-certified peripherals is likely to result in int

  • Graphtech SK200-09, 5-2 5.4 The control panel’s red ERROR LED is flashing 5.5 The document isn’t properly fed to the initial scanning position 5.6 The scanned image data is completely white or completely black 5.7 The image quality has dropped Cause The scanner was turned on with a document left loaded inside it. The top cover was opened during a scanning operation or while a document was left in the scanner. If the document is jammed… The length of the actual document is longer than the document length setting made in the Scanning Arts SP driver. The top cover is not fully locked. Remedy Open the cover and remove the document (see Secti

Related Products and Documents (Scanner):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Monoprice PID 8420 Operation & user’s manual monoprice/pid-8420-98H.pdf 18 Jul 2022 3
2 Mitsubishi Electric FL6900U Specification sheet mitsubishi/fl6900u-D8Z.pdf 03 Jun 2023 2
3 Asus RS320Q-E7 RS12 Operation & user’s manual asus/rs320q-e7-rs12-34Y.pdf 09 Jul 2023 158 5.45 Mb
4 HP Pavilion dv8-1000 - Entertainment Notebook PC Operation & user’s manual hp/pavilion-dv8-1000-entertainment-notebook-pc-713.pdf 25 Mar 2023 34 1.21 Mb
5 Samsung DVD-M405 Operation & user’s manual samsung/dvd-m405-NDJ.pdf 10 Mar 2024 20 1.51 Mb
6 Progression Fitness B890P Owner's operating manual progression-fitness/b890p-35D.pdf 06 Oct 2022 19

Similar Resources:

  • Avision

    AN230W

    (2 pages)
    Network Scanner EN Getting Started RU Краткое руководство PL Rozpoczęcie użytkowania JP 入門 KR 시작하기 ZT 入門指南 HR הדובעה תליחת Connect the Network Cable and Turn on the Power Obtain the IP Address Set Date and Time 2.1 2.2 2.3 2.4 …
  • Epson

    WorkForce 600 Series

    (8 pages)
    *411556300**411556300*Canada only: For French speakers, remove sticker(s) from the backing sheet and place over corresponding text on the control panel. Caution: Do not open ink cartridge packages until you are ready to install the ink. Cartridges are vacuum packed to maintain reliability.If anything is missing, contact Epson a …
  • Renkforce

    Smart Scanner ET16 Plus

    (8 pages)
    SicherheitshinweiseLesen Sie sich die Bedienungsanleitung aufmerksam durch und beachten Sie insbesondere die Sicherheitshinweise. Falls Sie die Sicherheitshinweise und die Angaben zur sachgemäßen Handhabung in dieser Bedienungsanleitung nicht befolgen, übernehmen wir für dadurch resultierende Personen-/Sach-schäden keine Haftung. Außerdem erlischt in s …
  • Epson

    PowerLite 715c

    (2 pages)
    STARTHEREEPSON®PowerLite®505c/715cQuick SetupConnect the power cord to your projector and plug the other end into a grounded outlet.The power light turns orange.3Connect the other end to your laptop’s video or monitorport. If you can’t connect the cable to your PowerBook®, youmay need to use an adapter. See your User’s Guidefor instructions …
  • Epson

    CX4800 - Stylus Color Inkjet

    (17 pages)
    Epson Stylus CX4200 Series/Epson Stylus CX4800 Series5/05 1Epson Stylus CX PartsAccessoriesInk CartridgesMediaPaper support extensionFeeder guardLeft edge guidePaper supportMemory card cover (Epson Stylus CX4800 Series only)USB external device connector(camera only)Document coverDocument tableMemory card slots (Epson Stylus CX4800 Series only)Output tray and …
  • Molecular Devices

    NanoScan SP Series

    (6 pages)
    www.prior.com QUICK START GUIDE USE OF METAMORPH WITH THE NANOSCAN SP RANGE OF SAMPLE SCANNERS AND THE NANOSCAN OP OBJECTIVE POSITIONER The NanoScan SP series sample scanners and the NanoScan OP400 objective positioner have basic control within Metamorph using the NanoScan Z functionality. CONNECTING YOUR SYSTEM - FRONT OF UNITPOS MON connector analogue po …

Comments, Questions and Opinions: