Manualios.com

GRAUPNER ASH 31 MI Instruction Manual

GRAUPNER ASH 31 MI Manual Online:

4.65, 1772 votes
GRAUPNER ASH 31 MI User Manual
GRAUPNER ASH 31 MI User Guide
GRAUPNER ASH 31 MI Online Manual

Text of GRAUPNER ASH 31 MI User Guide:

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 5 As you can see in the photos, stops in the hull are adhered at the ends of the flaps so that the flaps end flush with the outer contour of the hull. The ribs for the extend/retract drive and the retractable landing gear are only attached in the hull and still have to be adhered with 24-hour epoxy resin. The retractable landing gear and the extend/retract drive are mounted in the hull after the adhesive has hardened. Please follow the instruc

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 22 The purchaser must assert claim for guarantee performance in writing, which is to be accompanied by the original purchase receipt (e.g. invoice, receipt, delivery note) and this guarantee card. The purchaser must also return the defective goods to the above address at his/her own cost. The purchaser is to state in the claim the nature of the material or processing defect or the defect's symptoms specifically enough that a review of our guarantee obligation is possible. The transpo

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 11 fastened in the wing halves. The steering linkage is attached with a double elbow on the servo lever; see photo. To mark the length of the steering linkage, it must be attached to the lever in the landing flap. For this purpose, a threaded bush is soldered onto the end of the linkage and fitted with an M2 nut and an M2 clevis. When marking the length of the linkage, move the servo to the retracted position. F

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 6 The screw must be secured against loosening with UHU thread-lock. For the assembly of the tail wheel and the rudder servo, the recess at the hull end must be cut out and filed down to match the tail wheel. Adhere the fin end and rudder servo board together. Extend the rudder servo connection cable with the appropriate extension cable. Secure the plug connection against loosening. Using rubber bushes, rivets and the accompanying screws, fasten the servo to the board. Attach the rud

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 15 ASH 31 MI rudder throws Rudder +/- 45 mm Elevator +/- 8 mm Aileron 15 mm upward 5 mm down Center aileron 16 mm upward 6 mm downward Camber-changing flap 5 mm upward 4 mm downward All rudders move for with the aileron throw. With the specified throws the outer aileron have an equal throw to the inner camber-changing flaps. Exponential value for aileron 33 % for elevator 26 %

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 16 Do not extend the landing flaps too quickly and too far; they operate effectively. Extending the flaps approx. 5 mm is sufficient for the landing approach. Now all that remains is to have fun flying your ASH 31 MI. We hope you enjoy! Your team ! Part no. Designation Qty. Material Dimensions 1 Hull 1 GRP Finished part 2 Drive system flaps 1 pair GRP Finished part 3 Landing gear flaps 1 pair GRP Finished part 4 Hinged joints 8 plastic

  • GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 17 39 Clevis 8 Steel M2 40 Control arm 6 GRP Finished part 41 Threaded rod 8 Steel M2 42 Winglet 2 GRP Finished part 43 Fastening pin 2 Steel Ø 3x30 44 Fastening pin 2 Steel Øx30

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 14 Assembly of the ASH 31 MI Insert the wing halves on the hull using the mating so that the servo connection cables can be connected; then push both wing halves all the way onto the hull so that the root ribs are against the hull; insert the four anti-twist devices in the holes of the profile recesses of the hull. The two wing halves are secured by screwing in the locking screws with washers from the inside of the hull. Fit the outer wing on the inner wing using the GRP

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 4 Order no. 3935.65 For connection to the receiver 2 units Order No. 1587-20 Hook-and-loop cable tie 1 package As a receiver battery, we recommend a two-cell LiPo battery with a capacity of at least 5 Ah, e.g. Order no. 99013, which must always be well-maintained before and after flight. Rechargeable batteries are recommended for the receiver and transmitter, because they offer the great

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 18 The complete operating and assembly instructions must be read carefully before attempting to put the model into operation for the first time. You are solely responsible for the safe operation of your RC model aircraft. Youths who perform assembly and/or operate the model must be responsibly supervised by an adult who is familiar with the circumstances and potential hazards involved with RC model aircraft. Questions about the safe operation

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 23 • Protect the model and RC components against damage or slipping while they are being transported. • IMPORTANT: The rechargeable battery built into the model must not be disposed of in household waste. The rechargeable battery must be turned in at an appropriate collection point. IMPORTANT: The model and the transmitter may not be thrown away as household waste but must be turned in to a collection point for electrical waste materials. Ask your local authorities abo

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 1 for Order no. 42125 42135 Instruction Manual ASH 31 MI RC Glider and Electric Aircraft for Slope Flying, Towing and Electric Flight A remote control with 6 functions is needed! This models is not a beginner model and is only intended for experienced model builders! The present model is a technically mature design with well-balanced flight characteristics. The pre-assembly of a number of the individual parts enable

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 10 The cable on the servo can be left for the connection of the servo to the receiver, or it can be soldered to a G 6 plug (as shown in the photo), which is adhered in the recess. In parallel, the counterpiece must be adhered to the elevator support in the hull. Extreme care must be taken in the process in order to ensure that the plug

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 12 Before adhering the torsion pins, they must be roughened at the points to be adhered. When adhering, approx. 15 mm should protrude from the root ribs. As is shown in the photo, the servo connection cables can be run together using a G 6 plug connector. Attach the wiring harness in the hull from the receiver to the plug connection. In the process, the plus and minus leads can be run to

  • GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 20 Prior to every flight, check the entire RC system as well as the model aircraft for full functionality and range. Switch the transmitter on first and then the receiver system. In reverse order upon shutdown, be sure to switch off the receive

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 3 When using adhesives with solvents, make sure that the room is well-ventilated. Observe the manufacturer's notices. Remote control system Strongly recommended: Computer system mc-32 Recommended servos: Rudder DES 678 BB,MG Order no. 7943 1 unit Elevator DS 3288 BB,MG Order no. 5187 1 unit Outer aileron DS 3288 BB,MG Order no. 5187 2 units Center aileron DS 3288 BB,MG Order no. 5187 2 units Camber-changing flap DS 3

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 2 Technical data Wingspan, about 4510 mm Length about 1785 mm Wing airfoil TA06/11 Tailplane airfoil NACA 009 Total surface area about 79 dm² Flying weight depending on equipment from about 5500 g Glider 7000 g Electric Center of gravity about 95 mm behind the leading edge measured on the left and right of the hull. Longitudinal dihedral about 1° Notices for the construction of the model Before

  • GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 8 Adhere the boards for the receiver and drive battery fastening in the hull as shown in the two photos. In the following photo you can see the installation of the voltage regulator PS 5.9 volt. The cockpit canopy The co

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 7 Drill a Ø 2 mm hole on the left and right side of the hull for the bearing shaft of the tail wheel corresponding to the specifications in the photo. Mount the tail wheel together with the bearing shaft in the hull. Adhere the bearing shaft on the right and left sides of the inside of the hull. Check whether the rudder can move equally far to the left and right. Remove t

  • GRAUPNER ASH 31 MI, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Changes reserved! No liability for printing errors ID. no. 0063067 07/2012 19 Inform all persons passing by or watching about the hazards associated with your model before you start it. Always keep the necessary safe distance between the flying model and persons or objects; never execute low flying passes over or toward other persons! Model flying activity may only be pursued when outdoor temperatures are between -5 °C and +35 °C. Temperatures outside this range can lead to changes, e.g. rechargeable battery capacity, material characteristics and i

Related Products and Documents (Toy):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Volvo V70 Owner's manual volvo/v70-NIM.pdf 11 Mar 2023 306 7.59 Mb
2 Arbiter Systems 1088B Quick setup manual arbiter-systems/1088b-T73.pdf 17 Dec 2022 4
3 Metabo KS 55 Original instructions manual metabo/ks-55-82F.pdf 03 Aug 2023 76
4 Belkin 16-Port Gigabit Switch Operation & user’s manual belkin/16-port-gigabit-switch-H42.pdf 02 May 2023 266 8.48 Mb
5 Panasonic KX-TVP150 Operation & user’s manual panasonic/kx-tvp150-3PA.pdf 27 Aug 2023 581
6 Waldorf Attack Operation manual waldorf/attack-842.pdf 22 Apr 2023 37

Similar Resources:

  • Manzano Laser Works

    V1 Buzz Bomb

    (14 pages)
    V1 Buzz Bomb Construction ManualV1 Buzz Bomb1/9 Sport ScaleIntroductionIn the late stages of World War II, the Germans invented a new and terrible weapon, the V1 flying bomb. Though not nearly as accurate as today’s cruise missiles, it could hit a target such as a city from several hundred kilometers away.They were a 4,000 lb, 350 to 400 MPH pilot-less dr …
  • Makeblock

    mDrawBot Kit

    (9 pages)
    1 / 9 mDrawBot FAQs Q1. Why my PC can't install the driver of the Makeblock Orion successfully? A: If your PC can't install the driver for Makeblock Orion automatically, please manually download it and install. Dowonload link: http://learn.makeblock.cc/driver_installation/ To check whether the driver has been installed successfully: 1. Open R …
  • Eduard

    EA-18G exterior

    (6 pages)
    1/6EA-18G exterior 1/48 scale detail set for ITALERI kit •sada detailù pro model ITALERI 1/4848 74548 745ORIGINAL KIT PARTSPÙVODNÍ DÍLY STAVEBNICEPHOTO-ETCHED PARTSLEPTANÉ DÍLYPARTS TO BE REMOVEDDÍLY K ODSTRANÌNÍFILLTMELITeduardREMOVEODSTRANITOPTIONVOLBA?REPLACENAHRADITBENDOHNOUTGRINDOBROUSITSYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽDRILL HOLEVRTAT …
  • Vmar

    Piper J3 Cub 2000 Giant Scale ARF

    (15 pages)
    1Before beginning assembly,please read these intructions thoroughly.Photograph is nitro versionINSTRUCTION MANUALUNDER SAFETY PRECAUTIONSThis radio control model is not a toy!It is highly recommended that first-time builders seek advice of experienced modelers before beginning assembly.Assemble this kit only in places out of children’s reach!Take enough sa …
  • Phoenix Model

    YAK54 YAKOVLEV

    (16 pages)
    I/C FLIGHT GUIDELINESWhen ready to fly, first extend the transmitter aerial.Operate the control sticks on the transmitter and check that the control surfaces move freely and in the CORRECT directions.ALWAYS land the model INTO the wind, this ensures that the model lands at the slowest possible speed.Switch on the transmitter.Switch …
  • TWM

    Extra 300 EP (40)

    (12 pages)
    Wing SpanWing AreaFlying WeightFuselage Length 50.5 in / 1280 mm450 sq in / 29 sq dm53.5 oz / 1510 g42.5 in / 1100 mm450W Motor SystemRequires : 4-channel radio w/ 4 mini servos, Outrunner Motor KM374810, w/ Propeller Adaptor HW2340102, 40A Brushless ESC with 11x8E proepller, 4 cells 14.8 …

Comments, Questions and Opinions: