DynaColor DH701 Installation Manual
|
DynaColor DH701, Installation Guide 35 4) Fix the Indoor Mount Kit to the gooseneck tube with the supplied screws and washers. 5) Connect the cables to the dome camera. Then attach the dome to the Indoor Mounting Kit and fix them with the supplied screw. Please refer to 4.2.4 Ceiling Mounting with Straight Tube: step 6~9 for information about mounting with Indoor Mount Kit. Wall Mounting: Gooseneck Tube + Indoor Mount Kit 4.4.2 Mini Pendant Mount Items Needed: • Dome Camera • Mini Pendant Mount and other equippe
Installation Guide 22 Corner Thin Box 300(L)×164(W)×222(D) mm (11.8×6.5×8.7 inches); 3 kg (6.7 lbs); Supplied with washer×4, M8*16 screw×4 and spring washer×4. Corner Wide Box 232(L)×234(W)×210(D) mm (9.1×9.2×8.3 inches); 2.7 kg (6 lbs); Supplied with washer×4, M8*16 screw×4 and spring washer×4. Pole Thin Box 291(L)×136(W
Installation Guide 5 Table of Contents 1. Introduction................................................................................................................7 2. Standard Package Content .......................................................................................8 3. Dome Setups and Cable Connection ..........................................................
DynaColor DH701, Installation Guide 29 Step 2: Attach the separated wing to the dome, as shown in the figure. STEP 3 Place the Red Sticker on the ceiling plate, and cut the circle part out of the ceiling. STEP 4 Put up the T-Bar into the ceiling opening. STEP 5 Rotate T-Bar wings of the hinge to fix the T-Bar at the edge of the ceiling opening.
DynaColor DH701, Installation Guide 49 Cable Definition (D Protocol Keyboard to PTZ Camera) For SpeedDomeFor D Protocol Keyboard Tx- Tx + GND Rx- Rx+ 1 2 3 4 5 6 Tx - Tx + GND Rx - Rx+ 1 2 3 4 5 6 GND 6.2 Using Philips Allegiant Keyboard The dome cameras can be integrated into Philips Allegiant systems through D77R3 repeaters. Please follow the instructions to control dome cameras through Philips Allegiant systems. Symbol Definition <shot> Command dome cameras to go to specific preset position. <set> Set preset position. Special Function 7 6 <set> Exit OSD menu directly. 7 7 <set> 1. Display or hide OSD menu. 2. Virtual key to
DynaColor DH701, Installation Guide 8 2. Standard Package Content Before proceeding, please check the box contains the items listed here. If any item is missing or has defects, DO NOT install or operate the product and contact your dealer for assistance. Dome Body Hard Ceiling Mount and Decoration Ring Fixing Plate 5.4” Optical Cover 50-cm data cable for Power Supply, Video and RS-485 (24V AC model) 50-cm Data Cable for Power Supply, Video and RS-485 (12V DC model) Quick Guide CD: Operation Manuals Power Adaptor
DynaColor DH701, Installation Guide 27 STEP 5 Fix the Mount to the holes on the hard ceiling with three screws, as marked in the figure. STEP 6 Thread the data cable through the center hole of the Mount and connect the cable to the dome body. STEP 7 Attach the dome body to the Mount and rotate the dome clockwise. Tighten the fixing screw, as marked in the figure, to fix the dome body. STEP 8 Fix the decoration ring to the bracket. NOTE: Make sure the optical cover is removed before carrying out the procedure. STEP 9 Place the optical cover back to the dome camera.
DynaColor DH701, Installation Guide 36 2) To avoid insects entering the pendant mount, you could block the cable entry hole with the supplied sponge in two ways. See the illustrations below. 3) Thread the cables through the Mini Pendant Mount and fix the pendant mount on the wall with proper screws and screw anchors (not supplied). 4) Thread the cables through the Indoor Mount Kit and fix it to the Mini Pendant Mount with the supplied screws and washers. 5) Connect the cables to the dome camera. Then attach the dome to the Indoor
DynaColor DH701, Installation Guide 33 9) Mount the dome camera to the Indoor Mount Kit. (Ensure the dome camera is fixed completely, and the thread holes on the Lock Screw Plate and Indoor Mount Kit are aligned). Afterwards, screw the supplied standard screw / security screw, as shown in the picture. Ceiling Mounting: Straight Tube + Indoor Mount Kit
DynaColor DH701, Installation Guide 34 4.4 Wall Mount 4.4.1 Wall Mounting with Gooseneck Tube The following figures show how cables run through the tube in different ways. Cables exposed Cables recessed Items Needed: • Dome Camera • Gooseneck Tube and other equipped items (optional accessory) • Indoor Mount Kit and attached components (optional accessory) • Screws and Screw Anchors for fixing the gooseneck tube (not supplied) Tools Needed: • Tool for drilling • Tool for screwing Follow the steps to mount the dome with the
Installation Guide 19 Ceiling Panel For ceiling mounting. Zn platted; 610×305 mm (24×12 inches); Diameter: 155 mm (6.1 inches) Gooseneck Tube Iron; 298×385 mm (11.73×15.56 inches) ; 2.1 kg (4.6 lbs) Supplied with rubber washer-8×1, pendant tube washer×1, spring washer-8×1 and waterproof rubber×1, M8*12 screw×1. Mini Pendant Mount 184
DynaColor DH701, Installation Guide 4 • Do not use strong or abrasive detergents when cleaning the camera body Use a dry cloth to clean the camera when it is dirty. In case the dirt is hard to remove, use a mild detergent and wipe the camera gently. • Never face the camera towards the sun Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise, the camera may be smeared or damaged.
DynaColor DH701, Installation Guide 44 5. System Expansion 5.1 Connecting with Connector Box Ideally being used in indoor installation circumstances, a Connector Box provides easy wiring and well organized connection between alarms, cameras and other devices, for easy installation. To connect the connector box with other devices: • Use a RS-485 cable (CAT 5 is recommended) to complete RS-485 communication wiring with control devices such as DVRs and Control Keyboards. • Use a 22 pin cable to connect the connector box to the dome. For more detailed info
DynaColor DH701, Installation Guide 16 Insert the terminal into the pin holes on the connector housing, with the hook outward, as indicated in the figure. To unlock the terminal, press the hook, as indicated in the figure, with a proper tool and pull it out gently. Connect the 22-pin connector to the dome camera.
Installation Guide 21 Corner Standard Mounting Plate 222(L)×204(W)×117(D) mm (8.7×8×4.6 inches); 2 kg (4.4 lbs). Supplied with washer-8×4, spring washer×4, M8*16 screw×4, M8 nut×4. Pole Thin Direct Mounting 232(L)×136(W)×60(D) mm (9.1×5.4×2.4 inches); Diameter: 112~140 mm (4.4~5.5 inches); 0.7 kg (1.6 lbs). Supplied with stainless s
DynaColor DH701, Installation Guide 23 Pole Wide Box 270(L)×166(W)×155(D) mm (10.6×6.5×6.1 inches); 3.2 kg (7.1 lbs); Supplied with M8*16 screw×4, washer×4, spring washer×4, stainless steel straps×4. Wall Box Mounting 270(L)×166(W)×95(D) (10.6×6.5×3.7 inches); 2.2 kg (4.84 lbs); Supplied with M8*16 screw×4, washer×4, spring washer×4 Stainless Steel Straps For fixing Pole Direct Mounting/ Pole Box on the pole. Length: 700 mm (27.5 inches); Width: 0.63”; 0.02 kg (0.04 lbs) Stainless Strap Cutter For tension, cut and crimp stainless steel straps. 1.4 kg (3.1 lbs) Suitable for straps width: 1/2”, 5/8”, 3/4”
DynaColor DH701, Installation Guide 32 supplied) Tools Needed: • Tool for drilling • Tool for screwing Follow the steps to mount the dome with the straight tube. 1) Ensure that the ceiling can support the weight of the dome camera and straight tube. 2) Make a cable entry hole on the ceiling. 3) Fix the suspension bracket to the ceiling with proper screws and screw anchors (not supplied). 4) Thread the cables through the straight tube and the Indoor Mount kit. NOTE : After threading the cables, please block the cable entry hole with the supplied sponge(s) to avoid insects entering the tube. 5) Fix the Indoor Mount Kit to the straight tube with the sup
DynaColor DH701, Installation Guide 38 Indoor Mounting Kit and fix them with the supplied screw. Please refer to 4.2.4 Ceiling Mounting with Straight Tube: step 6~9 for information about mounting with Indoor Mount Kit. Wall Box Mounting: Wall Box + Gooseneck + Indoor Mount Kit 4.5 Corner Mount 4.5.1 Corner Standard/Mini Mounting Plate With the corner standard/mini mounting plate and gooseneck tube/mini pendant mount, the dome can be mounted on corner wall. Items Needed: • Dome Camera • Gooseneck Tube/Mini Pendant Mount and other equipped items (optional accessory) • Corner Standard/Mini Mounting Plate (optional accessory) • Indoor Mount Kit and attached co
DynaColor DH701, Installation Guide 13 3.2.2 22-Pin Data Cable DC 12V Data Cable Power Input DC12 Female Jack Video Output BNC Connector RS485 Connector 4-wire 2-wire AC 24V Data Cable Power Input 3-Pin Terminal Block Video Output BNC connector RS485 Connector 4-wire 2-Wire NOTE: Be careful not to pull the cables improperly during installation. Additionally, it is suggested to fasten the cables after cable connection is completed. Furthermore, when wiring the power cable, make sure the G/Y wire (Gr
DynaColor DH701, Installation Guide 31 STEP 9 Fix the decoration ring to the bracket and then place back the optical cover. NOTE: Make sure the optical cover is removed before carrying out the procedure. 4.3.3 In-ceiling Mounting with Ceiling Panel To mount the dome camera to a suspended ceiling with the T-Bar, the ceiling panel could be employed, as shown in the figure below. Follow the steps below for installing the ceiling panel. Step 1: Cut the ceiling half. Step 2: Put the ceiling panel upward to the ceiling opening. Step 3: Attach and fasten the T-Bar mount onto the panel (Refer to the previous section 4.2.2 In-ceiling Mounting for further details). 4.3.4 C
DynaColor DH701, Installation Guide 1 Preface The information given in this manual was current when published. The company reserves the right to revise and improve its products. All specifications are subject to change without notice. Notice This manual provides the installation information for the indoor integrated high speed dome. To work with the dome cameras, any installer or technician must have the following minimum qualifications: • A basic knowledge of CCTV systems and components • A basic knowledge of e
Sensormatic RT330C3 Security Camera Instructions
RT330C3 |
ring Spotlight Cam Security Camera Manual
Spotlight Cam |
Interlogix UVD-XP4DNR(-P) Security Camera Operation & user’s manual
UVD-XP4DNR(-P) |
Vitek VTD-C510 Security Camera Specifications
VTD-C510 |
DynaColor W series Security Camera Installation manual
W series |
DynaColor S3 Security Camera Installation manual
S3 |
Sony HDC-X300K Security Camera Brochure & specs
HDC-X300K |
DynaColor QIG-510 Series Security Camera Installation manual
QIG-510 Series |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Conrad | BT-FSE 1 | Operating insructions | conrad/bt-fse-1-21K.pdf | 16 Apr 2024 | 8 | |
2 | MG | CamStick-SD Mini DVR | Instructions | mg/camstick-sd-mini-dvr-91S.pdf | 10 Apr 2024 | 4 | |
3 | Elite Screens | Ez-Frame Series | Operation & user’s manual | elite-screens/ez-frame-series-381.pdf | 08 Oct 2022 | 8 | 0.4 Mb |
4 | Sony | XP-MP3 | Operating instructions manual | sony/xp-mp3-F69.pdf | 29 Dec 2022 | 146 | |
5 | Zanussi | ZFC 77/31 FF | Instruction booklet | zanussi/zfc-77-31-ff-IKA.pdf | 22 Nov 2023 | 20 | 1.23 Mb |
6 | Sony | SRF-M35 | Operating instructions | sony/srf-m35-4MV.pdf | 24 Aug 2022 | 2 | 0.11 Mb |
Spypoint
COMPONENTESKOMPONENTEN Starten123456781512131114101918171691Praxistip! Trennen Sie einen gewünschten Abschnitt dieser Anleitung ab und platzieren Sie diesen im Kameragehäuse.COMPOSANTSQuick start guidev1.4Models: BF-6 BF-8HD-7 2N1C6 ECLYPSEM8P INTSPY INTPSPYSurveillance cameraAdventure seriesAdventure series Série aventureAbenteuer-Serieserie de ave …
BF-6(2 pages) |
ENS Secuirity
Package Overview Installation1234► Connecting Network Cable213* 1 It is recommended to install the water-proof cap for network cable connection.* 2 If the PoE network switch is used to connect the camera that supports PoEpower supply, DC12V power supply is not required.① Loosen the nut from the main element.② Run the network cable (without RJ 45 conne …
TD-9541E2(2 pages) |
KGuard Security
QRT-502 connection method 1. Turn on QRT-502 first, then use the paperclip to press the Reset at the back for about 10 seconds, you will hear the DA ...DA ...DA, after releasing, QRT-502 will restart and wait for another sound Take the next step 2. After that, hold the paper clip and press Reset New York for 5-7 seconds. At this time, the QRT-502 light wi …
QRT-502(3 pages) |
FLIR
PT-Series CameraInstallation ManualFLIR Commercial Systems, Inc.70 Castilian DriveGoleta, CA 93117Phone: 888.747.FLIR (888.747.3547)International: +1.805.964.9797www.flir.comDocument Number: 427-0032-00-12Version: 150Issue Date: January 2012This document is controlled to FLIR Technology Level EAR 1. The information contained in this document is proprietary a …
PT series(27 pages) |
COP-USA
file:///C|/COP/specs/CM25W2-5.htm CM25W-2.5 - Wide Angle Bullet Camera Type:Color Indoor/ Outdoor Weather ResistantPick-up device:1/4" CCD image sensorPicture elements : EIA//NTSC: 512 H x 492 V - CCIR/PAL: 512 H x 582 V Horizontal resolution:420 TVL Minimun Illumination:0.1 LuxHorizontal Sync. frequency:EIA//NTSC: 15.734 KHZ - CCIR/PAL: 15.625 KHZVerti …
CM25W-2.5(1 pages) |
Honeywell
HED1PR3/HED3PR3 True Day/Night Indoor/Outdoor IR Ball IP Camera Quick Installation Guide Document 800-21229V1— Rev A — 10/2015 Thank you for purchasing a HED1PR3/ HED3PR3 camera. Follow the instructions in this guide to install and log in to your camera. For instructions on configuring the camera, refer to the Performance Series IP Cameras User Guide on …
Performance HED1PR3(2 pages) |
Carpigiani Beverage Dispenser 193 BAR PCarpigiani Beverage Dispenser 193 BAR P Instruction manual 193 BAR P, 37 |
Samsung Monitor T240 - SyncMaster - 24" LCD MonitorSamsung Monitor Guía de inicio rápido (File: samsung-t240-syncmaster-24-lcd-monitor-monitor-20, 28/02/2024) T240 - SyncMaster - 24" LCD Monitor, 20 |
Frigidaire Cooktop FEF369CGTDCooktop Wiring diagram (Frigidaire FEF369CGTD) FEF369CGTD, 1 |
REVELL Toy KIT 4241REVELL KIT 4241 Toy Assembly manual KIT 4241, 12 |
Makita Impact Driver TD090DInstruction manual for Makita TD090D Impact Driver TD090D, 44 |
Hyundai Radio H-1505User Guide: Hyundai H-1505 (72QA8U, Upd.13th Sep 2023) H-1505, 11 |
Nokia Cell Phone 6555 RM-276Nokia Cell Phone 6555 RM-276 Service schematics 6555 RM-276, 9 |
Toastmaster Iron 3310XIron Use and care manual (Toastmaster 3310X) 3310X, 7 |
Hasbro Game My Little Pony Balloon Flying Assortment 61644#62C73L: My Little Pony Balloon Flying Assortment 61644 Game Instruction manual My Little Pony Balloon Flying Assortment 61644, 4 |
Daewoo Air Conditioner DWC-051CUser Guide: Daewoo DWC-051C (4DA9I9, Upd.Tuesday 14-11-2023) DWC-051C, 16 |
Sony CD Player Walkman D-EJ775Sony Walkman D-EJ775 CD Player Operating instructions manual Walkman D-EJ775, 20 |
Planet Switch GSD-804P#184SCK GSD-804P: Planet Switch Owner Documentation GSD-804P, 24 |