Manualios.com

Allied GE4900 Operation & User’s Manual

Allied GE4900 Manual Online:

4.25, 873 votes
Allied GE4900 User Manual
Allied GE4900 User Guide
Allied GE4900 Online Manual

Text of Allied GE4900 User Guide:

  • Allied GE4900, GE4900 User Manual 70-0031A-B AVT Inc. 29 Triggering during the Readout State o For applications requiring the fastest triggering cycle time whereby the camera image sensor is exposing and reading out simultaneously, then the User Trigger signal should be applied as soon as a valid Trigger Ready is detected. o In this case, Trigger Latency and Trigger Jitter can be up to 1 line time since Exposure must always begin on an Interline boundary.

  • GE4900 User Manual 70-0031A-D AVT Inc. 13 Camera Installation Computer Interface The Prosilica GE Series cameras will work with any Gigabit Ethernet network card; however Prosilica strongly recommends using Gigabit Ethernet components that support Jumbo Frames. A Jumbo Frame is loosely defined as a frame size greater than 1500 bytes however typical Jumbo F

  • Allied GE4900, GE4900 User Manual 70-0031A-D AVT Inc. 2 Specifications Sensor Type Kodak KAI-16000 Sensor Shutter Type Progressive Interline Image Resolution 4872 x 3248 pixels Pixel Size 7.4µm x 7.4µm Optical Format 35mm optical format (43.3mm physical diagonal ) Lens Mount Nikon Bayonet (F-mount) -adjustable Color Sensor Filter Pattern † Bayer Full Resolution Frame Rate 3.35 fps Frame Rate (1024 x 1024 ROI) 7.04 fps I/O 1 isolated TTL compatible input, 3 isolated TTL compatible outputs. 1 RS-232 input/output. Power Requirements Less than 6.0W †† . 12V nominal. Digitization 12 Bits Trigger latency* 4.2µs Trigger Jitt

  • Allied GE4900, GE4900 User Manual 70-0031A-B AVT Inc. 24 GE IO Schematic VDD-3.3 LOGIC TXD ISO+5V MAX3221CPWR MAXIM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 EN C1+ V+ C1- C2+ C2- V- RIN ROUT INVALID DIN FORCEON DOUT GND VCC FORCEOFF ISO+5V SYNC OUT 1 LOGIC TRIGGER INPUT ISO_+5V SN74ACT244PWR TEXAS INSTRUMENTS 3 5 7 9 12 14 16 18 17 15 13 11 8 6 4 2 20 19 10 1 2Y4 2Y3 2Y2 2Y1 1Y4 1Y3 1Y2 1Y1 2A4 2A3 2A2 2A1 1A4 1A3 1A2 1A1 VCC 2OE GND 1OE IN TRIGGER INPUT MINI-SMB ISO+5V 0.1u IL716-3 NVE 1 2 3 4 5 6 7 89 10 11 12 13 14 15 16 VDD1 GND1 IN1 IN2 OUT3 OUT4 NC GND1G

  • GE4900 User Manual 70-0031A-D AVT Inc. 8 Item 4: Mini-SMB Sync Out 1 This Mini-SMB port on the camera uses an Amphenol 903-406J-51R connector. A suitable mating cable connector is Amp 413985-3 which can be used with RG174 coaxial cable. Contact Prosilica to purchase cabling. This connector is particularly useful for triggering mul

  • Allied GE4900, GE4900 User Manual 70-0031A-D AVT Inc. 17 Installing GigE Viewer for Testing o The latest Viewer software can be downloaded from http://www.prosilica.com/support.htm. o Run the GigE Viewer Installer.exe. This will install the Prosilica Digital Camera drivers as well as the Prosilica GigE Viewer application program. o Plug in the Prosilica camera via the Gigabit Ethernet port. Plug in the power connection. Verify that the Status LED 1 is a solid green. Run the Prosilica GigE Viewer Application. It will take a few seconds for the camera to be recognized. If the camera does not appear in the Viewer list a

  • Allied GE4900, GE4900 User Manual 70-0031A-B AVT Inc. 25 Hirose 12-pin Trigger Schematic USER TRIGGER (5V TTL DRIVER) SYNC OUT 2 ONE GROUND RETURN IS SUFFICIENT. SYNC OUT 3 (5V TTL RECEIVER) TRIGGER INPUT SYNC OUT 2 (5V TTL RECEIVER) USERS TRIGGER CIRCUIT CABLE SIDE SYNC OUT 3 1 2 3 4 5 6 7 8 9 10 11 12 HIROSE HR10A-10P-12P 1 2 3 4 5 6 7 8 9 10 11 12 The trigger circuit is connected to a Texas Instruments SN74ACT244PWR buffer/driver inside the camera. The required trigger input current is less than 10uA and the maximum sync output

  • Allied GE4900, GE4900 User Manual 70-0031A-D AVT Inc. 3 Supported Features Imaging Modes free-running, external trigger, fixed rate, software trigger Fixed Rate Control 0.001 fps to maximum frame rate External Trigger Delay 0 to 60 seconds in 1 microsecond increments External Trigger Event rising edge, falling edge, any edge, level high, level low Exposure Time 625 microseconds to 60 seconds in 1 microsecond increments Gain 0 to 28dB Region of Interest (ROI) independent x and y control with 1 pixel resolution*** Horizontal Binning 1 to 8 pixels Vertical Binning 1 to full resolution of sensor*** Pixel Formats

  • Allied GE4900, GE4900 User Manual 70-0031A-D AVT Inc. 7 Sync Out 2 and Sync Out 3 These signals only function as outputs and can be configured as follows: Exposing Corresponds to when camera is integrating light. Trigger Ready Indicates when the camera will accept a trigger signal. Trigger Input A relay of the trigger input signal used to “daisy chain” the trigger signal for multiple cameras. Readout Valid when camera is reading out data. Strobe Programmable pulse based on one of the above events. Imaging

  • Allied GE4900, GE4900 User Manual 70-0031A-D AVT Inc. 22 All stats 0 while streaming. Firewall likely blocking traffic • All stats 0. Likely a firewall is blocking incoming traffic. Disable your firewall. Check your camera trigger settings. Many camera trigger modes require a software or hardware trigger event to capture frames. • Packets are incoming, but all dropping. Be sure you have JumboFrames enabled on your NIC. Otherwise, decrease your PacketSize setting to 1500. • All packets completing as normal, but black image. Check ExposureValue, ExposureMode, and be sure your scene is suitably lit.

  • Allied GE4900, GE4900 User Manual 70-0031A-D AVT Inc. 1 Introduction The GE4900 series of cameras are sensitive, 3 frames per second, 16 megapixel, Gigabit Ethernet cameras based on the Kodak KAI-16000 CCD sensor. Precautions READ INSTALLATION GUIDE CAREFULLY. This document contains specific information which is necessary for the correct operation and treatment of this product. DO NOT OPEN THE CAMERA. WARRANTY IS VOID IF CAMERA IS OPENED. This camera contains sensitive components which can be damaged if handled incorrectly. KEEP SHIPPING MATERIAL. Poor p

  • Allied GE4900, GE4900 User Manual 70-0031A-B AVT Inc. 26 Mini-SMB Trigger Schematic OUT RG-174 COAX CABLE TRIGGER INPUT IN USERS TRIGGER CIRCUIT MINI-SMB MINI-SMB SYNC OUT 1 RG-174 COAX CABLE USER TRIGGER (5V TTL DRIVER) SYNC OUT 1 (5V TTL RECEIVER) The trigger circuit is connected to a Texas Instruments SN74ACT244PWR buffer/driver inside the camera. The required trigger input current is less than 10uA and the maximum sync output current is 24mA. See the Texas Instruments SN74ACT244PWR for more detailed information. Note that the trigger input signal is not terminated to match the cable impedance.

  • Allied GE4900, GE4900 User Manual 70-0031A-B AVT Inc. 28 Notes on Triggering Definitions o User Trigger is the trigger signal applied by the user. o Logic Trigger is the trigger signal seen by the camera internal logic. o Tpd is the propagation delay between the User Trigger and the Logic Trigger. o Exposure is high when the camera image sensor is integrating light. o Readout is high when the camera image sensor is reading out data. o Trigger Latency is the time delay between the User Trigger and the start of Exposure. o Trigger Jitter is the error

  • GE4900 User Manual 70-0031A-D AVT Inc. 4 Mechanical 109.7* M3 3MM DEEP 16 PLCS TYP 50 TYP 26 TYP 49* 66 66 All dimensions are in mm. *Add 0.3mm for color cameras due to addition of IR blocking filter. Figure 1. GE SERIES mechanical dimensions.

  • Allied GE4900, GE4900 User Manual 70-0031A-D AVT Inc. 15 o Select the Internet Protocol (TCP/IP) check box and then select Properties. See Figure 6. Network card TCP/IP address.. Select the Use the following IP address and enter an IP address of 169. 254. x. y, where x and y can be any number. Press the TAB key after entering the IP address and the subnet mask will automatically be entered. The subnet mask is 255. 255. 0. 0. Click OK to save changes. Note that if Windows reports a conflict with the above IP address, simply repeat the above steps and change the last digit of the

  • GE4900 User Manual 70-0031A-D AVT Inc. 11 Adjusting the F-mount SET SCREW 3 PLCS TYP F MOUNT FRONT ASSEMBLY Figure 4. Camera Front View. THE F-MOUNT IS ADJUSTED AT THE FACTORY AND SHOULD NOT REQUIRE ADJUSTING. If for some reason, the F-mount requires adjustment, use the following method. Attach F-mount compatible lens Use a

  • Allied GE4900, GE4900 User Manual 70-0031A-D AVT Inc. 21 The following example is not on the same Subnet: NIC IP 169.250.23.2 Subnet Mask: 255.255.255.0, CamIP 169.254.13.0 Subnet Mask: 255.255.0.0. This can happen if you use a non AutoIP range on your NIC and it doesn’t have access to a DHCP server. Either change your NIC IP to be in the AutoIP range, or fix the camera IP address to be on the same subnet as your NIC. • Camera is not listed, or flashing “Camera Unavailable”: There may be multiple NICs on your system set to the same subnet. The camera can not know which card to resolve

  • Allied GE4900, GE4900 User Manual 70-0031A-D AVT Inc. 20 Trouble Shooting Is the camera getting power? The right LED is the camera power indicator. If unlit, check the power adaptor. If possible, swap with one that is known to work. If using a custom power adaptor, be sure the adaptor and wire gauge is rated to at least 500 mA. If the right LED still does not light up, contact Prosilica support. Is the camera powered, but not detected in SampleViewer? Damaged or poor qual

  • Allied GE4900, GE4900 User Manual 70-0031A-D AVT Inc. ii Table of Contents Table of Contents ............................................................................................................................ ii Introduction .................................................................................................................................1 Precautions ..................................................................................................................................1 Warranty .

  • Allied GE4900, GE4900 User Manual 70-0031A-D AVT Inc. 19 Figure 10. Network card advanced settings. o Set Maximum Frame Size or Jumbo Frames to the maximum possible value. A typical value is 9000. If the list contains a property called Receive Descriptors, then change this value to its maximum value. Select OK to save properties. o From the main properties dialog as in Figure 9, make sure that only the Internet Protocol (TCP/IP) check box is selected then click OK. The card is now optimized for use with the Prosilica camera. o Open the viewer and set the PacketSize to 8228.

  • Allied GE4900, GE4900 User Manual 70-0031A-D AVT Inc. 12 Loosen F-MOUNT FRONT ASSEMBLY Use a 1.5mm hex wrench to loosen the 3 set screws which hold the F-mount front assembly to the camera body. Image to Infinity Set the lens to infinity and image a distant object. The distance required will depend on the lens used but typically 30 to 50 feet should suffice. Gently move the F-mount front assembly until the image is in focus. Carefully tighten the 3 set screws. Recheck the focus.

  • Allied GE4900, GE4900 User Manual 70-0031A-D AVT Inc. 6 Item 1: GIGABIT ETHERNET PORT This port conforms to the IEEE 802.3 1000BASE-T standard for Gigabit Ethernet over copper. It is recommended that CAT5E or CAT6 compatible cabling and connectors be used for best performance. Cable lengths up to 100m are supported. Item 2: General Purpose I/O PORT 1 2 3 4 5 6 7 8 9 10 11 12 PIN FUNCTION 1 Trigger Input 2 Sync Out 2 3 Sync Out 3 4 RS-232 RXD 5 RS-232 TXD 6 DNC 7 DNC 8 DNC 9 DNC 10 Isolated Ground 11 Isolated Ground Figure 3. General Purpose I/O Pin out. Camera rear view. 12 Isolated Ground The General Purpose I/O port

  • Allied GE4900, GE4900 User Manual 70-0031A-D AVT Inc. 14 Gigabit Ethernet Setup for Windows o Install network card in computer. o Boot the PC and cancel the “Found new Hardware Wizard” window that may appear when Windows detects the new card. o Install the driver that came with the network card. o Once the driver is installed, open the Network Connections Dialog as follows: From the Windows desktop select start, then select Control Panel, then double click on the Network Connections icon. Double click the relevant network card listed or right

  • Allied GE4900, GE4900 User Manual 70-0031A-B AVT Inc. 27 Trigger Timing Diagram User Trigger Logic Trigger Exposure Readout Trigger Ready Imaging Tpd Trigger Latency Interline Time Expose Start Delay Trigger Jitter Idle Registered Exposure Time Readout Time N N+1 N N+1

  • Allied GE4900, GE4900 User Manual 70-0031A-D AVT Inc. 18 System Optimization o Open the Network Connections Dialog as follows: From the Windows desktop select start, then select Control Panel, then double click on the Network Connections icon. Double click the relevant network card listed or right-click the relevant network card and select Properties. This will open the properties window for your network card. See Figure 9. Figure 9. Network card main properties window. o From the Pr

  • Allied GE4900, GE4900 User Manual 70-0031A-D AVT Inc. 9 Item 7: AUXILIARY POWER PORT This port is required to provide power to the camera. This port provides threaded captivation of the power cable if required. The captivated cable mating connector is the Switchcraft 760K. This connector can be purchased from Prosilica or from http://www.digikey.com. Cameras designated as “A”, with serial number 02-2xxxA-xxxxx can accept an input voltage range of 5V to 17V DC. Cameras designated as “C”, with serial numbers 02-2xxxC-xxxxx and later versions can accept an input voltage range of 5V to 24V DC

Related Products and Documents (Digital Camera):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Tchibo CAFISSIMO MINI Instruction manual and warranty tchibo/cafissimo-mini-I6E.pdf 21 Jan 2024 15
2 Sony Vaio Pro 13 Quick start manual sony/vaio-pro-13-YZ9.pdf 10 Jan 2023 2
3 audiophony Ti300 Operation & user’s manual audiophony/ti300-5N7.pdf 18 Jul 2023 12
4 TONWERK T-LINE?eco2 Operating instructions manual tonwerk/t-lineeco2-97Y.pdf 05 Sep 2022 238
5 Yealink Yealink SIP-T26P Operation & user’s manual yealink/yealink-sip-t26p-5MM.pdf 11 Aug 2023 54
6 Maytag MSD2542VE - 25.0 cu. Ft. Refrigerator User instructions maytag/msd2542ve-25-0-cu-ft-refrigerator-Y8G.pdf 31 May 2023 51

Similar Resources:

  • Samsung

    Series 4000

    (16 pages)
    - 1 -Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance. Product design and specifications may be changed without notice.Still image warningAvoid displaying still images (such as jpeg picture files) or still image elements (such as TV channel logos, panorama or 4:3 image format, stock …
  • Kaiser Baas

    X360

    (6 pages)
    X360 | Quick Start Guide X360 | Quick Start GuideQUICK START GUIDEENGLISHHold the POWER button for 3 second to turn the X360 ON.1Video Mode is selected by default. Press the Record Button to start recording.2To toggle between Video and Photo Mode, click the Power button.3Note: Before using the X360 for the first time it is recommended that you fully char …
  • OWIM

    Z31833

    (81 pages)
    IAN 103897 IMITATION SURVEILLANCE CAMERA ÜBERW ACHUNGSKAMERA-ATTRAPPE Montage-, Bedienungs- und Sicherheitshinweise IMITATION SURVEILLANCE CAMERA Assembly, operating and safety instructions ATRAPA KAMERY DO MONITORINGU Wskazówki montażu, obsługi i bezpieczeństwa LAŽNA KUPOLASTA KAMERA Navodila za montažo, uporabo in varnostna navodila …
  • Philips

    LTC0600

    (11 pages)
    Subject to changes without notice.© Philips I&C 19993122 165 21872Digital Color Camera Installation manualInstallationsanleitungManuel d’installationManuale d’installazioneInstallatiehandleidingManual de instalaciónLTC0600 …
  • Yashica

    8T2

    (25 pages)
    DisclaimerThe information contained in this Adobe PDF file is for general information purposes only. Due to the age of the information and the difficulty in converting it to computer formats it may not be up to date or correct, we make no representations or warranties of any kind, express or implied, about the completeness, accura …
  • Sena

    PRISM

    (2 pages)
    PRISM Quick Start GuideTapTapping1”Press for 1 secButton OperationStatus LEDMode ButtonStatus LCDShot ButtonLensMicrophoneCamera LCD Menu ScreenPower On/OffMemoryCounterBluetooth Battery lifeResolution / fpsCamera mode0000FOVPower Onpress+1”Power OffTapTap+Mode ChangeBURSTSETTINGSVIDEOSINGLEPLAYBACK*ConfirmTapShot ButtonNext MenuTapMode Buttonpress1”En …

Comments, Questions and Opinions: