Sinclair ASH-24CN Owner's Manual

Text of Sinclair ASH-24CN User Guide:

• Sinclair ASH-24CN, 22 Installation dimension diagram IMPORTANT NOTES The installation must be done by trained and qualified service personnel with reliability according to this manual. Contact with service center before installation to avoid the mal - function due to unprofessional installation. When picking up and moving the units, you must be guided by trained and qualified personnal. The air conditioner should be connected to the earth, correctedly, if not, contact with the service center. ´Ö¹Ü 3 7 8 m m 57 2mm 3 0 c m or mo r e 2 0 0 c m o r m o r e 30cm or m o r e 5 0 c m o r mor e 66162002 6 02 11

• Sinclair ASH-24CN, 14 Select the most appropriate temperature. It can avoid the electricity westing. The airflow direction can be adjusted appro- priately. The louvers can be adjusted downward at heating operation, and upward at cooling op- eration. Don’t leave windows and doors open while the air conditioner is on for a longtime. It can decrease the air conditioning capacity. Splashing water on the air conditioner can cause an electric shock and mal - function. Air conditioner should be operated with stable voltage in range of 198 -- 244V 1ph. other

• -- 11 -- 11 SLEEP mode operation procedure As the unit is cooling or drying, if SLEEP operation is set, SET TEMP. would increase 1 o C in 1 hour and 2 o C in 2 hours. As the unit is heating, if SLEEP operation is set, SET TEMP. would decrease 1 o C in 1 hour and 2 o C in 2 hours. 4. Press FAN button, set fan speed. 3. Press SWING button, the louvers start to rotate automatically

• Sinclair ASH-24CN, 20 Weight(kg) Dimension(cm) (Width height depth) Indoor unit/ outdoor unit Indoor : 90.7 29.0 19.5 Outdoor :95.0 70.0 41.0 12/59kg All above are test according to CHINA NATIONAL STANDARD GB/T 7725-1996. All above should be changed without notice, there are latest and accurate specifications on the nameplate of your air conditioner. * “Memory function” means that after the power supply turns off sucldenly and then turns on, the air conditioner automatically runs in the old state, the compressor runs in 3 minutes later after the power supply turns on again. (Remark: The memory function will be clear when the unit is stopped by the remote controller). Working temperature range Maximum

• Sinclair ASH-24CN, 16 Maintain after use Clean filters and other parts. Turn main power off. Clear dust from the outdoor unit If there is any rust in the outdoor unit, this should be painted over to prevent it from spreading. Preparation before use Be sure that nothing obstructs the air outlet and intake vents. Check that whether ground wire is properly con- nected or not. Replace filters if necessary. 4. Replace the batteries if necessary. Remove the Air Filters (Refer to the first step of “cleaning the Air Filters”) Replace the Air cleaner Take off the packed bag of Ai

• Sinclair ASH-24CN, -- 9 -- 9 AUTO mode operation procedure Under Auto mode operation, standard SET TEMP. is 25 o C for COOL mode and 20 o C for HEAT mode . 1. Plug in, Press 1/0 button, then air conditioner is turned on. 2. According to room temp., mi- crocomputer can automatically set operation mode, so as for best effect. 1/0 66162002 6 02 11 30 10 249

• Sinclair ASH-24CN, 8 DRY mode operation procedure If room temp. is lower than set temp. , compressor, outdoor and indoor fan motor stop. If room temp. is between 2 o C of set temp., Air conditioner is drying. If room temp. is higher than set temp., it’s at COOL mode. SET TEMP. should be in range of 16 o C to 30 o C. 3. Press SWING button, the louvers start to rotate au- tomatically, and stop when repress it. 4. Press TEMP. button, set suitable SET TEMP. 2. Press MODE button, set operation mode. Air speed couldn’t be changed after the “ ” being set. 1. Plug in, press 1/0 button, then air conditioner is turned on. 1/0 66162002 6 02 11 30 10 248

• Sinclair ASH-24CN, -- 13 -- 13 The best operating methods adjust to the switable temp. too cool will do harm to the helth. pull off the plug if the unit will be free in a long time. advoiding directly lighting and cool air leaking. cleaning the air filter seriously and maitaining the air cleaner carefully take out the batter- ies if the remote control- ler will be free within a long period. 66162002 6 02 11 30 10 2413

• Sinclair ASH-24CN, 24 Install the rear panel 1. Always mount the rear panel horizontally. 2. Fix the rear panel on the selected loca- tion with screws supplied with the unit. 3. Be sure that the rear panel has been fixed firmly enough to withstand the weight of an adult of 60kg, furthermore, the weight should be evenly shared by each screw. (Fig.1) Wrenched Bent Flooded Install the indoor unit Install the connection pipes Connect the connection pipes with the relevant union pipes of the indoor unit (Shown in P26 “Install the connec- tion pipes”) NOTE: Connect the connection pipes with the indoor unit firstly and the outdoor unit secondly. Be careful in bending the connection pipes, or yo

• Sinclair ASH-24CN, 26 Install the outdoor unit Install the connection pipe 1.Align the center of the piping flare with the relevant valve. 2.Screw in the flare nut by hand and then tighten the nut with spanner and torque wrench refer to the diagram at right. Note: Exceeding tightening torque will damage the flare surface. Tightening torque table Hex nut diameter (mm) Tightening torque (N.m) 6 15~20 31~35 50~55 9.5 12 Electric wiring connection 1.Remove the front side plate (Fig.8) 2.Break through the hole for wires and put on rubber bush. 3.Pull all wires throught the rubber bush. 4.Remove the wire clamp and connect the

• Sinclair ASH-24CN, 30 User notices Care and Maintenance Troubleshooting Technical specifications Install the indoor unit Install the outdoor unit Routine check after installation Accessories and Installation diagram Installation location CONTENT Thank you for choosing this Air conditioner, please keep this owner’s manual carefully for consultation. The instructions before use Name and function of each part Name and function - Remote control Name and function - Remote control (Remove the cover) COOL mode operation procedure DRY mode operation procedure AUTO mode operation procedure TIMER mode operation procedure SLEEP mode operation proced

• Sinclair ASH-24CN, 6 4. Press FAN button, set fan speed. 3. Press SWING button, the louvers start to rotate au- tomatically, and stop when repressed. 5. Press TEMP. button, set suitable SET TEMP. 2. Press MODE button, set operation mode. 1. Plug in, press 1/0 button, then air conditioner is turned on. COOL mode operation procedure 1/0 According to difference between room temp. and set temp., microcomputer can control cool- ing on or not. If room temp. is higher than set temp. , compressor runs at COOL mode. If room temp. is lower than set temp., compressor stops and only indoor fan motor runs.

• Sinclair ASH-24CN, -- 1 -- 1 WARNING The power plug must be in- serted tightly. Otherwise, it can cause an electric shock, overheating or fire.The ground must be connected. for the security of the air condi- tioner, it should be safely connected to earth. The line that be connected to the earth of the outdoor unit should be connected correctedly and tightly. The instructions before use Don’t pull out the power plug during operation. It can cause an electric shock or fire. Never splice the power cord or use an extended cord. It ca

• Sinclair ASH-24CN, 2 Don’t use any other fuse ex- cluding the fuse of correct capacity. Improper wire could cause the breaking down or fire. Be sure to pull out the power plug as the Air Conditioner will not be used for a longtime. When cleaning, it is neces- sary to stop driving and turn off the power suply. It occasionally cause the elec- tric shock. Don’t pull the power cord to pull out the power plug. It can cause fire. Don’t place a space heater near the air conditioner. Air flow from the air conditioner can cause incomp

• Sinclair ASH-24CN, 28 Check after installation Check after installation Items to be checked Possible mal-function Situation Has it been fixed firmly? The unit may drop, shake or emit noise. Have you done the refrigerant leakage test? It may cause insufficient refrigerating capacity. Is heat insulation sufficient? It may cause condensation and dripping. Does the unit drain well? It may cause condensation and dripping. Is the voltage in accordance with the rated voltage marked on the nameplate? It may cause electric mal-function or damage the part. Has the unit been connected to a secure earth connection? Is the electrical wiring and piping connection installed correctly and securely? It may cause electr

• Sinclair ASH-24CN, 18 Immediately stop all operations and plug out, contact with service center in following situations. Unusual noise can be heard during operation. Power fuse or switch often breaks. Carelessly splash water or something into air conditioner. Electrical lines and power plug are very hot. Wind blowing from the outlet smells terrible during operation. NOTE: Equipment subject to notification to or consent by the supply authority before connection to the system (consent by the supply authority may be requested for high-power appliances which are intended to be used only in systems having impedances considerably lower than the reference impedance. General consent may declared for use of a type of

• Sinclair ASH-24CN, 12 1. Remove the cover from the back of the remote control. 2. Insert the two batteries (Two AAA dry - cell batteries) and press button “ACL”. 3. Re - attach the cover. NOTE: Don’t confuse the new and worn or different types of batteries. Remove batteries when the remote controller will be not in use for a longtime. The remote control sig- nal can be received at the distance of up to about 10m. The lifetime of the bat- teries is about one year. The remote controller should be placed about 1m or more away from the TV. or any other electric applianc

• Sinclair ASH-24CN, -- 5 -- 5 Liquid crystal displayer It shows all set contents. SLEEP button Press this button to set SLEEP operation. and stop when repressed TIMER OFF button At operating, press TIMER OFF button, set OFF TIME in range of 0 to 24 hour to stop the unit auto- matically. Name and Function-Remote control .(Remove the cover) This type of remote controller is a kind of new current controller. some buttons of the controller which are not available to this Air conditioner will not be described below. Operate on unmentioned buttons would not impact on the normal use. 1/0 Note: 0 - 24h Timer cancellation TIMER ON button At stopping, press TIME ON

• -- 3 -- 3 Name and function of each part Indoor unit Outdoor unit Air in Air out Air in Air out Surface panel Air cleaner Air Filter A Air Filter B Wiring cover Handling switch Power line Drain hose Air outlet grille Louver Wireless remote controller Operation Timer Operation indicator (red) lights up when the unit is on, and flashes when the unit is defrosting. 11

• Sinclair ASH-24CN, -- 15 -- 15 Take down surface panel and washing Pull along the direction of arrows to take down surface panel. Washing Wipe with a cloth slightly moistened with water or cleaner, and then dry it in the shade. NOTE: Never use water above 45 o C to wash the panel, or it could cause deformation or discolouration. Install surface panel Cover the surface panel and clasp it. Cleaning the Air Filters (Recommended once every three months) Open the surface panel, hold the tab of Air Filter and raise it slightly, and then take it out. Cleaning To clean the dust adhering to the filters, you can either use a vacuum cleaner, or wash them with wa- ter and dry it in the

• Sinclair ASH-24CN, -- 27 -- 27 Connecting the pipe 1.Remove the flare nuts from the cut-off valves of the out- door unit. 2.Align the center of the piping flare with the relevant valve, and screw in the flare nut about 3~4 turns by hand. 3.Tighten the flare nut with spanner and torque wrench. 4.Remove the valve caps of the gas valve and liquid valve and the service port nut. Air purging and leakage test For the air conditioners with R22 refrigerant, as the below step: 1.Loosen the valve stem of the liquid valve with a hex wrench. 2.Push the check valve core of the gas

• 4 Name and Function-Remote control COOL mode DRY mode FAN mode HEAT mode AUTO Remote control operation procedure Note: Be sure that there are no obstructions between reciever and remote controller. The remote control signal can be received at the distance of up to about 10m. Don’t drop or throw the remote control. Don’t let any liquid in the remote controll

• Sinclair ASH-24CN, -- 25 -- 25 NOTE: All the electrical work must be done by qualified personnel according to the local rules and this manual. The rated voltage and the exclusive circuit must be used. Leakage circuit-breaker must be installed. Please use specified fuse. If the power supply cord of the unit is damaged, it must be replaced by a special cord or assembly available from the manufacture or its service agent. The diameter of power cord should be large enough. Use the exclusive wire to replace the damaged wire. Wiring

• AIR CONDITIONER Internet: http://www.sinclair-eu.com E-mail: [email protected] SPLIT AIR CONDITIONER WALL MOUNTED MODEL SINCLAIR OWNER‘S MANUAL ASH-24CN NATURE SERIE Before operating the unit please carefully read this manual.

• Sinclair ASH-24CN, -- 19 -- 19 Technical specifications Functions Accessory Cooling capacity (W) Heating capacity (W) Power supply Cool 4500W ---- Cooling/Heating rated power 1950/-W Recyling air volume Waterproof level Noise (Indoor/outdoor) dB (A) Climate type Anti-electric shock protection Weight(kg) Dimension(cm) (Width height depth) Indoor unit/ outdoor unit 620m 3 /h 43/56 dB(A) Indoor : 90.7 29.0 19.5 Outdoor :95.0 70.0 41.0 Frequence Cooling/Heating rated current Maximum input current 8.9A 7.83/-A Refrigerant and weightt Model Cool Heat 4500W 5200W 1950/2055W 8.9A 7.83/7.83A Cool 5000W ---- 2400/-W 12A 9.0/-A Cool Heat 5000W 6200W 2400/2650W 12A 9.0/10A Cool 5000W ---- 2400/-W 12A 9.01-A Cool

• Sinclair ASH-24CN, 10 TIMER mode operation procedure TIMER ON button At stopping, press TIME ON button, set ON TIME in range of 0 to 24 hour to start the unit automatially. TIMER OFF button At operating, press TIMER OFF button, set OFF TIME in range of 0 to 24 hour to stop the unit automatically. 1/0 0 - 24h Timer cancellation 0 - 24h Timer cancellation 66162002 6 02 11 30 10 2410

• -- 21 -- 21 Accessories and Installation diagram Accessories (Check that all accessory parts are present before installation) Be sure to use the exclusive accessories list above in the installation, or it will lead to water leakage, electric shock, fire, etc. No. 1 2 3 4 5 Part name Rear panel Wireless remote controller Battery Power connection cord Control cord Memo Specification Qty Di

Related Products and Documents (Air Conditioner):

Comparable Devices:

Similar Resources:

• Technibel Climatisation GR8F98R5IAA (18 pages) TECHNICAL DATA& SERVICE MANUALOUTDOOR UNIT:GR8F98R5IAAGR8F128R5IAASPLIT SYSTEM AIR CONDITIONER 0.8180.565.00 10/2008GR8F128R5IAA 387107097Model No. Product Code No.GR8F98R5IAA 387107096 …

• Mitsubishi Electric EW-50A (60 pages) Air Conditioning Control SystemCentralized Controller EW-50A/EW-50EBefore installing the controller, please read this Installation Manual carefully to ensure proper operation.Retain this manual for future reference.Installation and Instructions ManualSafety notes are marked with WARNING or CAUTION, depending on the severity of possible consequences that may …

• LG ARNU073TEC2 (13 pages) OWNER’S MANUALAIR CONDITIONER Please read this manual carefully before operatingyour set and retain it for future reference.TYPE : Ceiling Cassette - 4WayP/NO : MFL42803015www.lg.comhttp://www.lghvac.comENGLISH FRANÇAISESPAÑOL …

• ONNLINE N09ILE (40 pages) The design and specifications are subject to change without prior notice for product improvement. Consult with the sales agency or manufacturer for details.CS159U-BP11M20200019248520130513Before using your air conditioner, please readthis manual carefully and keep it for future reference.Read This ManualKeep this manual where the operator can easily find the …

• Carrier bryant 577C-C (60 pages) 1577C----C, 577C----ELEGACYt 14 SEER SINGLE--PACKAGED AIR CONDITIONER ANDGAS FURNACE SYSTEM WITH PURONR (R--410A) REFRIGERANTSINGLE PHASE 2--5 NOMINAL TONS (SIZES 24--60)THREE PHASE 3--5 NOMINAL TONS (SIZES 36--60)Installation InstructionsIMPORTANT: Effective January 1, 2015, all split system andpackaged air conditioners must be installed pursuant to applica …

• North American HVAC Products MSV1-18HRDN1-MQ0 (39 pages) NORTH AMERICAN HVAC PRODUCTS LTD Tel: 604-4308496 Fax: 1-866-9034371 www.northamericanhvac.com Service Manual DC Inverter Single Zone Split Wall-Mounted Type Model …

Comments, Questions and Opinions: