Smartswitch SMS-2 Installation Manual

Text of Smartswitch SMS-2 User Guide:

• Smartswitch SMS-2, 15 Make an Output pulse On and Off Command: Make OUTPUT NAME pulse XX secs This sets the output pulse time, XX can be between 1 and 99 seconds When the Output ON command is sent as follows: Turn OUTPUT NAME On The Output will turn On for the programmed pulse time and then turn Off, the system responds with: OUTPUT NAME has been pulsed on and off If you try and set an Input as a pulse Output, the system responds with: Sorry pulses only apply to outputs, please check the name and try again If the Output is already a pulsed Output the system responds with: OUTPUT NAME is already a pulsed output so

• 9 Removing a Administrator Command: Remove admin The system responds with: The administrator number and feature has been removed Note: this completely removes the administrator from the user list, it does NOT move the user down a security level to normal “user” unless the administrator is the only number in the system in which case it will move the user

• 20 Penguin Electronics Ltd (the manufacturer) warrants that all of its products are free of defects. Any apparent fault will be rectified free of charge by Penguin Electronics Ltd for a period of 12 months from purchase date, provided that:  All costs of insta

• Smartswitch SMS-2, Air Conditioners / Heating Different brands of Air-Con’s use different means of remotely turning On and Off. Type1: If the brand requires that the Output to be turned On and left On then you can use either Output 1 or 4. eg. Turning the output relay On will start the Air-Con and turning the relay Off will stop the Air-Con. 1. Change the Output name as per page 12: Naming Inputs and Outputs and Changing Names 4. Turn output On as per page 15: Turn an Output ON or OFF 4. Turn output Off as per page 15: Turn an Output ON or OFF Type4: If the brand requires that the Output be pulsed On and Off to turn the Air-C

• Smartswitch SMS-2, 16 Turn Output response On / Off This command is used to turn the output response text On or Off. If the output response is turned off then a response text is not sent when outputs are turned on or off System default is ON (send response). To turn the feature on: Command: Turn respond on The system responds with: This feature has been enabled, response text will be sent To turn the feature off: Command: Turn respond off The system responds with: This feature has been disabled, response text will not be sent Save

• Smartswitch SMS-2, 14 Turn an Output ON or OFF Command: Turn OUTPUT NAME on (or) off (Example: Turn Generator on) If everything is fine, the system responds with: OUTPUT NAME has been turned off (or) on This command is used to turn on/off Outputs. If the item named is not an Output or the command is not spelt correctly the system responds with: Sorry either that output does not exist or the options ON or OFF has not been used Turn an Output ON for XX mins or hrs or days Command: Turn

• Smartswitch SMS-2, 13 Link an Input to an Output Command: Link INPUT NAME to OUTPUT NAME (Example: Link alarm to siren) The system responds with: The INPUT NAME has been linked to OUTPUT NAME To clear a link Command: Clear INPUT NAME link (Example: Clear alarm link) The system responds with: The link between INPUT NAME and OUTPUT NAME has been cleared Function: If a link is setup between an Input and an Output and the Input is turned ON, the Output will also turn on. Full control of the Output is still available.

• Smartswitch SMS-2, 10 Turn all Input Text’s OFF With alerts turned off the device will NOT text every time any Input changes but the Inputs are still active so you can send a “Input status” query at any time. Command: Alerts off The system responds with: Alerts have been disabled (this is saved to memory and will still be disabled even after the unit is reset or rebooted) OR Command: Alerts off exc links ( note only available in ver 1.2 or higher) The system responds wit

• Smartswitch SMS-2, 23 Appendix Two: SMS-2 Application Notes Figure 1 Fixed Wiring Shore Power Monitoring (requires a registered electrician) Smart Switch SMS-2 Installation & Operation Manual - Gnd SMS-2 Input 1 Terminal 4 or Input 2 Terminal 6 + 120/230 VAC to 12 VDC adapter plugged into vessel AC outlet and connected as shown p rovides simple and inexpensive means to monitor shore power connection Simple Shore Power Monitoring A n inexpensive and effective mean

• Smartswitch SMS-2, 8 Adding a User ( Note: Setting up the first user page 7 must be done first) Command: Add user +??XXXXXXXX (see Country Code page 7) If the master is already in the list, the system responds with: Sorry +??XXXXXXXX is already active and cannot be added twice, please check the number and try again If the number does not fit the checks, to confirm it is a valid number (all digits must be numbers excluding the leading +), the system responds with: +??XXXXXXX

• Smartswitch SMS-2, 12 Change Input to Normally Open or Normally Closed Command: Make INPUT NAME active open (or) closed This command is used to define if the switch wired to the Input is normally open or normally closed. The Input defaults are set for a normally open switch (which is active closed). That is, the Input becomes active when the switch is closed. Active closed means: the Input switch is normally open and goes closed to activate Input. Active open means: the Input switch is normally closed and goes open to activate Input . The system responds w

• 5 The SMS-2 has two (2) Outputs. The Outputs are Relays rated at 3 A resistive @ 125VAC Relay 1 Connection Internal Relay Relay Terminals 7-8 Outputs Smart Switch SMS-2 Installation & Operation Manual !! Important Note !!

• 3 • Receive text messages on your cell phone alerting you to potential problems anywhere in the world • Send commands to control lights, pumps, appliances, air conditioning, etc. via text message from your cell phone • Connects to most GSM networks world-wide • Module= Duel Band 900/1800MHz • Up to 5 cell phones may be designated as “ma

• Smartswitch SMS-2, 21 Appendix One: Record Your Names for all Inputs and Outputs Input Default Name [Name] (Up to 20 characters ) Latched Yes No Linked to Active Open or Closed 1 input1 2 input2 Output 1 output1 2 output2 Smart Switch SMS-2 Installation & Operation Manual Detailed explanation of Input delays: On Delay: This delay is used when the input t

• Smartswitch SMS-2, 25 Door and Window Alarms Alarms sensors for doors and windows generally consist of magnetically held switches. The contacts are normally-closed (NC). If a door/window is opened the circuit is opened generating an alarm. An alarm is also generated if the wire is cut between the sensor and the monitoring system opening the circuit. This prevents an intruder from defeating the alarm system by merely cutting a wire. The wiring diagram for the window/door switches is similar to the motion detector and the same basic commands are used to set up the motion detector. Smart Switch SMS-2 Installation & Operation Manual Send command text: Change input ? to Do

• Smartswitch SMS-2, 19 Get Firmware Version Command: Ver The system responds with: SMS-2 Ver X.X Get Signal Strenth Command: Sig The system responds with: Currently the signal strength is XX %" Resetting the Unit Command: Reboot The system responds with: Module is not resetting Reset Unit to Factory Defaults ------------------------------------------------- WARNING ------------------------------------------------------- This command restores the unit to factory defaults therefore all settings

• Smartswitch SMS-2, 6 The SMS-2 has two (2) Inputs and can be connected as per Fig 1a /Fig1b or Fig 2 Inputs Smart Switch SMS-2 Installation & Operation Manual SMS-2 Input 1 Terminal 4 Switch +10 - 30vdc Fig 1a SMS-2 Input 2 Terminal 6 Switch +10 - 30vdc Fig 1b SMS-2 Terminal 3 Switch / Input1 Fig 2 Switch / Input2 Terminal 4 Terminal 5 Terminal 6

• Smartswitch SMS-2, 27  All technologies, design and Intellectual property is owned by Penguin Electronics Ltd New Zealand Version 2.1

• Smartswitch SMS-2, 2 Table of Contents Features 3 System / Connections 4 Outputs 5 Inputs 6 COMMANDS Getting Started – Setting Up Initial Owner 7 Adding a Master 8 Removing a Master 8 Adding an Administrator 8 Removing the Administrator 9 Get a list of all the Masters 9 Turn programmed numbers lookup on or off 9 Text all programmed numbers on or off 9 Turn All Texts OFF and Disable Inputs 10 Turn All Texts ON and Enable Inputs 10 Testing 10 Get a List of the Inputs 10 Get a List of the Outputs 10 Naming Inputs/Outputs and Changing Names 11 Change the Input Delays 11 Change Input to Normally Open or Normally Closed 1

• Smartswitch SMS-2, 11 Naming Inputs and Outputs and Changing Names: Command for initial Naming or changing name of Input or Output: Note: The system default names are: Inputs: Input1, Input2 Outputs: Output1, Output2 The name can contain a dash ( – ) but NOT a space. eg. “Pond-pump” is OK Command: Change Current Input or Output Name to New Input or Output Name (Example: Change input1 to Alarm) (Example: Change output1 to Pump) This command is used to change Inputs and Outputs to a new name. Names can be words up to a total length of 20 characters, please note the name can contain a

• Smartswitch SMS-2, 18 Alive text feature. (only available in ver 1.2 or latter) This unit has an alive text feature which will send out a alive text as often as it has been programmed for. To turn the feature on: Command: Turn alive text on every xx yy (where xx=1 to 99, yy = hrs or days) This sets how often the alive text is sent out, XX can be between 1 and 99 Example: Turn alive text on every 2 days Every 2 days the Alive text will be sent out If everything is fine, the system responds with:

• Smartswitch SMS-2, 24 Intruder Alarm Systems The following configurations define possible solutions for intruder alarms. Like all other alerts provided by the SMS-2, these should be disabled prior to you entering the premises. This is easily accomplished by issuing the text command: Alerts off when leaving the premise, simply issue the text command: Alerts on Connecting to a PIR motion sensor Commands Send command text: Change input ? to Sensor Send command text: Make Sensor latching Send comman

• Smartswitch SMS-2, 7 Setting up system for the first time: Please ensure the SIM card does NOT have a PIN number or is locked has been ACTIVATED with the network provider, insert into SIM slot on the back (see page 4) and power the unit up. When the unit is first powered ON a mobile (cell phone) number must be set for initial programming. This phone number is called the “Initial Owner”. You must wait for the LED to be slowing flashing (EVERY 3 seconds) before sending any commands. Please wait a few minutes, as the unit will set auto- band and other details for the country. IMPORTANT: For all text commands, spelling and spaces must be strictly followed.

• Smartswitch SMS-2, 22 Trouble Shooting Guide PROBLEM CAUSE POSSIBLE SOLUTION LED not flashing No power Check power supply LED fast flashes (every 1 second) and never slow flashes (every 3 seconds) Cannot find the GSM network 1. Replace aerial with high gain aerial 2. Move unit to different location 3. SIM card not installed 4. SIM has a

• Smartswitch SMS-2, 17 Link the Battery Alarm to an Output Command: Link battery alarm to OUTPUT NAME The system responds with: The battery alarm has successfully been linked to OUTPUT NAME and the alarm has been reset To clear or remove the link Command: Clear battery link The system responds with: The battery alarm Output link has been removed Function: If a link is setup between the Battery Alarm and an Output then when the Battery Alarm turns ON, the linked Output wil

Related Products and Documents (Security System Monitor):

Comparable Devices:

Similar Resources:

• Sanyo VMC-8618 (16 pages) INSTRUCTION MANUALColor Video MonitorVMC-8618VMC-8613About this manual•Before installing and using this unit, please read this manual carefully. Be sure to keep it handy for later reference.•This manual gives basic connections and operating instructions for 2 models.L8MV5/US, L8MW5/US (VMC-8618, 8613 GB) 2001. 2. 23 …

• Brigade BE-970WM (12 pages) BE-970WM vehicle CCTV monitorUser & fitting guideUser Guide & montageUser & Einbau AnleitungUtente di montaggio e guidaGuía de usuario y montajeUser & montage handleidingStock code #3431 …

• Inter-m PM-6228 (12 pages) Operation ManualMonitor PanelPM-6228* Rack mount products in the Western Hemisphere(North America, South America,and the Caribbean) do not have handles installed due to customer preference. …

• Sanyo VMC-8618 (24 pages) VMC-8618FILE NO.REFERENCE No.SM5310261L8MV5/US,XE,UK,AUNOTE: 1. Parts order must contain model number, part number, and description.2. Substitute parts may be supplied as the service parts.3. N.S.P. : Not available as service parts.Design and specifications are subject to change without notice.(Product Code : 114 950 71)(U.S.A, Canada)SERVICE MANUALColor Vid …

• Speco VMS-3 (1 pages) 3.5” Color LCD Test Monitorwith Cable Tester & Built-In Rechargable BatterySpecifications subject to changeFor more information contact us at:Speco Technologies 200 New Highway, Amityville, NY 11701 Web: www.specotech.comToll Free: 1-800-645-5516 In Metro NY: 631-957-8700 Fax: 631-957-9142 or 631-957-3880Features• Video and audio input• 480 x 234 l …

• Speco VMS-2 (1 pages) VMS-2Portable CCTV Installation & Test Monitor In a Soft Light-Weight Carrying CaseSpecificationsLCD technology TFT active matrixDisplay size 4”Active area 82.1 x 61.8mmColor system NTSCSynchronization Horizontal 15,625Hz, Vertical 60HzResolution 480 x 234, 112,320 pixelsAudio level 1V/10KCharging time 8 hours charging time, 4 hours operating timeInput …

Comments, Questions and Opinions: