Soundwin P100 Operation & User’s Manual

Text of Soundwin P100 User Guide:

• Soundwin P100, 3.6.3 Port Settings: you can setup the SIP and RTP port number in this page. Each ISP provider will have different SIP/RTPport setting, please refer to the ISP to setup the port number correctly. When you finished the setting, please click the Submit button. SIP Port: 5060 (0~65533, 0-> auto)。 RTP Port: 20000 (0~65533, 0-> auto)。 SIP Port Range: 10000 ~ 10999 (1024 ~ 40000)。 RTP Port Range: 20000 ~ 21999 (1024 ~ 40000)。

• 2 PREFACES About This Manual This manual is designed to assist users in using P100 VOIP Phone. Information in this document has been carefully checked for accuracy; however, no guarantee is given as to the correctness of the contents. The information contained in this document is subject to change without notice. Copyright Declarations Copyri

• Soundwin P100, 18 LAN Settings: In this page you can configure the IP Phone LAN port‟s setting. The LAN port‟s default IP address is 192.168.123.1, Net Mask is 255.255.255.0., and DHCP Server enabled. The start IP address if 150, end IP adress is 200. It is not necessary to change the LAN settings. You can connect your PC to the LAN port, set your PC as DHCP Client mode, then you can get IP addreess from the TA. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save bu

• Soundwin P100, 20 the VID, if the packets is not going to the TA(with the TA‟s IP address and the correct VID), and the VID is not these four VID you set, then the packets will be discard by the TA. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically. 3.5.6 DMZ Settings: In computer networks, a DMZ (Demilitarized Zone) is a computer host or small network inserted as a "ne

• Soundwin P100, 16 3.5 Network 3.5.1 In Network you can check the Network status, configure the WAN Settings, LAN Settings, DDNS settings and VLAN Settings. 3.5.2 Network Status: You can check the current Network setting in this page.

• Soundwin P100, 5 3 Setup the VoIP Phone by Web Browser Default the IP Phone‟s NAT is enabled, WAN port is in DHCP Client Mode, LAN port is in DHCP Server Mode. You can connect you PC on LAN port, then you will get an IP Address from the IP Phone. The IP Phone provides a built-in web server. You can use Web browser to configure the IP Phone. First please input the IP address http://192.168.123.1:8888 in the Web page. Please remember to add the port number “:8888”. 3.1 Login. 3.1.1 Please input the username and password into the blank field. The default setting is: 1. For Administrator Username: admin Password : admin If you use the ac

• Soundwin P100, 3 1 Introduction This user‟s manual is for VoIP Phone. This user‟s manual will explain the keypad instruction, web configuration and command line configuration for the VoIP Phone. Before using the VoIP Phone, some setup processes are required to make the VoIP Phone work properly. Please refer to the Setup Menu for further information. 1.1 Hardware Overview The VoIP Phone has the following interfaces for Networking, telephone interface, LED indication, and power connector. 1.1.1 Two RJ-45 Networking interface, these two i

• Soundwin P100, 8 If IP Phone user dial “2222#” the device will search phone book , If match the device will send out “[email protected] “. If you want to delete a phone number, you can select the phone number you want to delete then click “Delete Selected” button. If you want to delete all phone numbers, you can click “Delete All” button. 3.3.3 The Speed Dial setting function you can add/delete Speed Dial number. You can input maximum 10 entries speed dial list. If you need to add a phone number into the Speed Dial list, you need to input the position, the name, and the phone number (by URL type). When you finished a new phon

• 13 3.4.6 Dial Plan Setting function: This function is when you input the phone number by the keypad but you don‟t need to press “#”. After time out the system will dial directly. Symbol explan: Replace rule:If replace prefix code is ON and prefix number is matched with rule then 005 will replace prefix. Auto Dial Time : Stop dialing after

• Soundwin P100, 1 Example: Auto configuration: FTP, FTP Server: 192.168.123.100, FTP username: download, FTP password: 1234567, FTP Patch: /download/ (Device will connect to the Ftp server /download folder patch and download the matching file) 3.8.2 Auto configuration (Auto provision function) : Step1: Login P100 WEB other  Auto Configuration Setting, enable SW Ipbx Auto function & Auto Configuration TFTP bottom , next step must submit and save/reboot.

• Soundwin P100, 21 3.5.7 Virtual Server Setting : The device can be configured as a virtual server so that remote users accessing services such as Web or FTP services via the public (WAN) IP address can be automatically redirected to local servers in the LAN network. Depending on the requested service (TCP/UDP port number), the device redirects the external service request to the appropriate server within the LAN network. You will only need to input the LAN IP address of the computer running the service and enable it. A Virtual Server is defined as a service port, and all requests to this port will be redirected to the computer specified by the server IP. Enable Selected (Button

• Soundwin P100, 4 2 Keypad interface for IP Phone demo system 2.1 Keypad description Key Name Description Note 1 “1”, “-“, “٫”, “!”, “?” 2 “2”, “a”, “b”, “c”, “A”, “B”, “C” 3 “3”, “d”, “e”, ”f”, “D”, “E”, “F” 4 “4”, “g”, “h”, “I”, “G”, “H”, “I” 5 “5”, “j”, “k”, “l”, “J”, “K”, “L” 6 “6”, “m”, “n”, “o”, “M”, “N”, “O” 7 “7”, “p”, “q”, “r”, “s”, “P”, “Q”, “R”, „S

• Soundwin P100, 2 3.8.5 ICMP Setting: you can setup the ICMP echo Enable/Disable in this page. This function can disable echo when someone ping this device, it can avoid haker try to attack the device. When you finished the setting, please click the Submit button. ICMP Not Echo: Not be responded for all ping messages. Default is no. Send Anonymous CID: Send Caller id to anonymous. Default is no. Send Flash event: Provides two methods for sending DTMFEven or SIP info messages. Encryption Type: Encryption Key: PPPoE retry period: Specifies the time taken to redial when PPPoE dialing fails. Default is 5 Seconds. Time range is 5-255 System Log

• 23 3.6 SIP Settings 3.6.1 In SIP Settings you can setup the Service Domain, Port Settngs, Codec Settings, Codec ID Settings, RTP Setting, RPort Setting and Other Settings. If the VoIP service is provided by ISP, you need to setup the related informations correctly then you can register to the SIP Proxy Server correctly. 3.6.2 In Service Domain Functio

• Soundwin P100, 19 3.5.5 VLAN Setting: You can set the VLAN setting in this page. There are two parts in this page. First one is to set the packets related to the TA, and the second parts is if you use the VLAN setting in the NAT Mode. There are two kind of destination packets will come from the TA‟s WAN port, one kind of packets will go to the TA, the other will go through the LAN port to the PC. VLAN Packets: if you enable the first VLAN Packets and set the VID, User Priority, and CFI, then all the

• Soundwin P100, 1 3.6.4 Codec Settings: you can setup the Codec priority, RTP packet length, and VAD function in this page. You need to follow the ISP suggestion to setup these items. When you finished the setting, please click the Submit button.

• 6 3.1.2 Click the “Login” button will move into the VOIP PHONE web based management information page. 3.2 System Info. 3.2.1 When you login the web page, you can see the VOIP PHONE current system information like firmware version, company… etc in this page. 3.2.2 Also you can see the function lists in the left side. You can use mouse to click t

Related Products and Documents (IP Phone):

Comparable Devices:

Similar Resources:

• Philips VOIP4332B (2 pages) PhilipsMessenger PhoneVOIP4332BFREE worldwide internet calls*The VOIP433 is a dual DECT phone, which allows you to make or take normal telephone calls on your landline as well as free or cheap calls through Windows Live™ Messenger. Access your contacts list simply by pressing the Messenger key.Talk freely to millions• Free calls worldwide via Windows Li …

• Polycom SoundPoint IP 450 (2 pages) Polycom SoundPoint IP 450 Phone Quick User Guide. 1725-12490-001 Rev A 09/2008Polycom® SoundPoint® IP 450 PhoneQuick User GuideBasic Phone FeaturesCustomizing Your PhoneApplies to phones running SIP 3.1 or later.For detailed information, see the User Guide for the Polycom SoundPoint IP 450 Phone at: www.polycom.com/support/voicedocumentation/ ©2008 Polyc …

• ShoreTel 485g (2 pages) ShoreTel, Inc., 960 Stewart Drive Sunnyvale, California 94085 USA Phone: +1.408.331.3300 +1.800.425.9385 Fax: +1.408.331.3333 www.shoretel.comShoreTel IP Phone 485g Quick ReferencePHONE OPERATION Place CallsUse the speakerphone or a headsetor + Ext.Use the Directory+ to select + Make a conference call+ Ext. + or Make a call from History+ t …

• Yealink T20P (3 pages) User Guide – Yealink T20P http://www.virtualglobalphone.com Dec - 2014 Is a entry level IP Phone with high-definition audio, a broad range of voice codec’s support. Its easy to install and inexpensive from to start up for both enterprise and residential users. YealinkT20P These instructions are based on using the T20 in its factory defau …

• Inter-Tel 560.4200 (23 pages) Courtesy of Main Resource, Inc. Visit us at www.MainResource.com or call 800 362-6740 for all your Inter-Tel needs. Page 1 of 23 Inter-Tel Eclipse2 Associate Display and Basic Digital Phone User’s Guide Associate Display Phone 560.4200 Basic Digital Phone 560.4100 …

• Nortel Nortel IP Phone 1120E (8 pages) 1 1120E IP Phone Your 1120E brings voice to the desktop by connecting directly to a Local Area Network (LAN) through an Ethernet connection. In this guide, self-labeled line/programmable feature key labels appear beside the keys, and context-sensitive soft key labels appear directly above the keys. The following shows self-labeled line/programmable feat …

Comments, Questions and Opinions: