Aiwa XR-M700 Service Manual
|
Aiwa XR-M700, – 34 – CD TEST MODE 1. How to activate 1) Insert AC plug into an outlet while pressing the CD function button. (Fig.1 1) 2) Display will be all lit as shown in Fig2 in CD test mode (All FL display on). 3) Press the CD function button again to switch into mecha test mode as shown in Fig.3. 4) Press the CD function button in order to switch between CD and mecha test modes. Fig.1. Front View Fig.3. Display in Mecha Test Mode Fig.2. Display in CD Test Mode
– 35 – 2. Mecha Test Mode 1) By pressing the following buttons, up and down operation of the elevator, and the OPEN/CLOSE operation of the frame (tray), can be controlled and operated regardless of the positions of mecha and switches. Note 1: It displays FRAME OPEN/CLOSE while the elevator is in the top position. It displays TRAY OPEN/CLOSE if the elevator is in any other positions. Note 2:
Aiwa XR-M700, – 4 – 1-3. Removing the GEAR, ELEVATOR 1) Remove the GEAR, ELEVATOR. 1-4. Removing the CD MAGAZINE Part 1) Remove the GEAR, TRAY A and B, etc. to make it look like in the photo. 2) Remove the 2 screws and PWB, TRAY.
– 22 – 10) Pass the FFC, 4P through the rib of the BASE, and connect it to the connector of the switch circuit board. Refer to the “6-5. Marking of each GEAR” for the further details. 3-2. GEAR, PULLY for the ELEVATOR UP/DOWN Assembly and Phase Adjustment. 1) Rotate the GEAR, SLIDER B fully to the direction of the arrow. Make sure that the claws of the GEAR, SLIDER B and t
Aiwa XR-M700, – 19 – 2) Fit the A’, B’, and C’ of the HLDR CLAMP to the A, B, and C of the BASE respectively, and set the HLDR, CLAMP into the BASE. Push the HLDR, CLAMP till it chucks with click. 3) Place the PLATE, ELEVATOR on top of the BASE.
Aiwa XR-M700, – 36 – 2) Each mecha switch and ON/OFF position of sensors may be checked on display. SW and Sensor Frame OPEN / CLOSE SW TRAY No. Detection SW Elevator Position Detection SW Faulty Disc Prevention Sensor Tray Edge Detection Sensor Tray No. Detection SW Ref. No SW204 SW202 SW201 Q202 Q212 PS231 SW213 SW212 SW211 Position of SW and Sensor Frame is in OPEN position. Frame is in MIDDLE position. Frame is in CLOSE position. Tray 1 is in PLAY position. Tray 2 is in PLAY position. Tray 3 is in PLAY position. Elevator is in TOP position. Elevator is in CD3 position. Elevator is in CD2 position. Elevator is in CD1 position. Elevator is in PLAY position. Elevat
Aiwa XR-M700, – 12 – 2-1. Removing the Pick-up 1) Turn over the CD mechanism and short-circuit the shotland (indicated by the circle) at the pick-up. 2. Procedure of Replacing the Pick-up 2) Disconnect the FFC, 16P and FFC, 6P. 3) Remove the 2 pieces of the Washer W-P, 2.08-8-0.5 (87-B10-273-010).
SERVICE MANUAL DATA COMPACT DISC STEREO SYSTEM BASIC TAPE MECHANISM : 2ZM-1 R9NM BASIC CD MECHANISM : ZZG-4 YB XR-M700 K S/M Code No. 09-009-430-8S1 SUPPLEMENT • This Service Manual contains the additional information “CD MECHANISM DISASSEMBLY INSTRUCTIONS” and “CD TEST MODE” for the model XR-M700 (K). If requiring the other information, see Service Manual of XR-M700 (K), (S/M
Aiwa XR-M700, – 28 – 3-5. Marking of each GEAR * In case of replacing all the GEAR, MAGAZINE / GEAR, ELEVATOR, GEAR, TRAY AB with new GEAR, use a white marker for marking. 1) Mark the dented teeth with rib of the GEAR, MAGAZINE. 2) Mark the upper and bottom of the GEAR, ELEVATOR. As for the upper side, mark the tooth of the both side of a dent mark. As for the bottom side, on the other hand, mark the 2nd and 3rd from the right of 5 projected tooth. 3) Mark the projected part of the GEAR TRAY AB.
Aiwa XR-M700, – 5 – 3) Remove the claws indicated by the circles in order to remove the MAGAZINE, TOP. Insert a minus driver into the gap and remove the MAGAZINE, TOP by lifting it upward. 4) Remove the MAGAZINE, TOP. 5) Remove the TRAY 1,2,3 and 3 pieces of MAGAZINE by lifting them up.
Aiwa XR-M700, – 21 – 6) Fix the HLDR, LINK R with screws. Then install the spring (88-ZG5-292-010). 7) Fix the HLDR, LINK L in the same step as R, and then install the spring (88-ZG5-292-010). 8) Insert the LEVER, LOCK F till the click sound comes out. 9) Install the spring (88-ZG5-225-010).
Aiwa XR-M700, – 8 – 8) 1 Lift up the PLATE, ELEVATOR, together with the HLDR, CLAMP. 2 Once lift it up to the TOP position, pull it toward the front side. Then remove the PLATE, ELEVATOR and HLDR, CLAMP. 9) Views after removing the ELEVATOR part and MAGAZINE part. * At this stage, the mechanism’s pick-up can be changed. Refer to “5. Procedure of Replacing the Pick-up” for details.
Aiwa XR-M700, – 20 – 4) Set the boss of the LEVER, ASSY LINK into the groove of the LEVER, SLIDER (on the both sides of L and R). 5) 1 Insert the boss of the LEVER, ASSY LINK R into the hole (O) of the HLDR, LINK R and pull it down. 2 Then rotate it as shown in the photo, in order to set the boss into the hole on the front side of the HLDR, LINK R.
Aiwa XR-M700, – 18 – 3-1. Assembly the ELEVATOR Part 1) Lift up both the LEVER, CATCHER L (in red solid line) and R (in red dotted line) and remove the HLDR, CLAMP. 3. ZZG-4 Mechanism Assembly and Phase Adjustment
Aiwa XR-M700, – 9 – 1-6. Removing the ELEVATOR UP/DOWN Components. 1) Remove the BELT, SLIDER and BELT, BASE. Then remove the 2 screws, the PULLEY, SLIDER and PULLEY, BASE. 2) Remove the screw and GEAR, SLIDER C.
Aiwa XR-M700, – 32 – 4) Set the left-hand side of the FRAME, MAIN onto the rail. 5) Insert the 1 FRAME, MAIN all the way to the end. Press the 3 FRAME, MAIN until the 2 LEVER, LOCK F get set into the groove of the FRAME MAIN. 6) Install the PLATE, FRAME L with screws.
Aiwa XR-M700, – 25 – 2) First, hook the rear side of the CD circuit board on the picks. Then position it on the front side. Make sure that the boss of the SW 201 and SW204 are fitted into the dent (O) of the GEAR, SLIDER B and the LEVER, SW F respectively. Then connect the 3 FFCs to the CD C.B. 3) Install the CD P.W.B. with screw.And solder the legs of the motors of M201 and M202. screw
Aiwa XR-M700, – 29 – 3-6. GEAR, ELEVATOR Phase Adjustment 1) Put the marked teeth of the 1 GEAR MAGAZINE and the marked teeth (on the upper side) of the GEAR, ELEVATOR together, and put back the GEAR ELEVATOR itself to the original position. Then insert the 2 SHAFT, ELEVATOR (make sure the up and down) and fix it. 3-7. GEAR, TRAY AB Phase Adjustment 1) Rotate the GEAR, BASE fully to the direction of the arrow.
Aiwa XR-M700, – 10 – 3) Turn over the CD mechanism and short-circuit the shortland of the pick-up. 4) Desolder M201 and M202. And remove the screw. Disconnect FFC (3 parts) and remove the CD C.B from the BASE. screw
Aiwa XR-M700, – 31 – 5) Install the HLDR, SHAFT with screws. 6) Rotate the GEAR, SLIDER B to position the ELEVATOR at the TOP position. 3-8. FRAME, MAIN Installation 1) At this point, three marked GEAR should be positioned at the GEAR position with the TRAY on top of the ELEVATOR. Rotate the GEAR, BASE fully to the direction of the arrow. 2) Lower down the ELEVATOR to the bottom again. 3) Set the right-hand side of the FRAME, MAIN onto the rail.
Aiwa CSD-TD31 Micro Music System Operating instructions manual
CSD-TD31 |
Aiwa CSD-EX151 Micro Music System Operating instructions manual
CSD-EX151 |
Aiwa CS-P5 Micro Music System Operating instructions manual
CS-P5 |
Aiwa JAX-S5 Micro Music System Operating instructions manual
JAX-S5 |
Aiwa Z-A60 Micro Music System Operating instructions manual
Z-A60 |
Aiwa NSX-Aj14 Micro Music System Operating instructions manual
NSX-Aj14 |
Aiwa XR-H33MD Micro Music System Operating instructions manual
XR-H33MD |
Aiwa NSX-V9000 Micro Music System Operating instructions manual
NSX-V9000 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | GE | E1680W | Operation & user’s manual | ge/e1680w-I74.pdf | 19 Jan 2024 | 86 | 5.21 Mb |
2 | Rheem | 701 | Owner's manual and installation instructions | rheem/701-9G6.pdf | 22 Jul 2023 | 34 | |
3 | Zoom | Cable Modem/Router | Quick start | zoom/cable-modem-router-693.pdf | 12 Aug 2022 | 2 | |
4 | THOMSON | 28VT68N | Operation & user’s manual | thomson/28vt68n-JC3.pdf | 04 Oct 2022 | 30 | 1.41 Mb |
5 | HP | Mini 200 | Maintenance and service manual | hp/mini-200-AJW.pdf | 10 Sep 2023 | 97 | |
6 | Lexmark | 363dn - X B/W Laser | Service manual | lexmark/363dn-x-b-w-laser-47T.pdf | 16 Sep 2023 | 244 |
Philips
Philips HarmonyComponent Hi-Fi systemDock for iPod/iPhone/iPadDAB+DCB8000Natural, true-to-life soundObsessed with soundA top-mounted tweeter delivers your favourites with details that sound natural. Whether you are playing and charging an iPod/iPhone/iPad, or listening to crackle-free DAB+ radio, this aluminium Philips Hi-Fi system offers a great experienc …
DCB8000(3 pages) |
Sharp
MODELLMODÈLEMODELOMODELLMODELLOMODEL MODELBEDIENUNGSANLEITUNGMODE D’EMPLOIMANUAL DE MANEJOBRUKSANVISNINGMANUALE DI ISTRUZIONIGEBRUIKSAANWIJZINGOPERATION MANUALCD-BA250HCD-BA2600HMINI KOMPONENTEN SYSTEMMINI-CHAÎNESISTEMA MINIMINI KOMPONENT SYSTEMMINI SISTEMIMINI SYSTEEMMINI COMPONENT SYSTEMMini Komponenten System CD-BA250H/CD-BA2600H besteht aus CD-BA250H …
CD-BA250H(42 pages) |
Philips
Register your product and get support atMCM906 EN User manual 3 DA Brugervejledning 26 DE Benutzerhandbuch 50 ES Manual del usuario 76 FR Mode d’emploi 102 IT Manuale utente 127 NL Gebruiksaanwijzing 152 SV Användarhandbok 176 Book_1.indd Sec3:1Book_1.indd Sec3:1 2008-07-29 17:27:552008-07-29 17:27:55
…
MCM906(26 pages) |
Philips
USB/USB/MCD297Quick Start GuideWhat’s in the Box?You should find these items upon opening the box.1Quick Start GuideQuick Start GuideComposite Video CableRemote control withbatteryMW antenna FM antenna2User ManualUser ManualRemove the plasticprotective sheetMCD297 QUG_Eng 2008.6.24, 10:37 AM1
…
MCD297/12(4 pages) |
Philips
www.philips.com/welcomeUser manualAlways there to help youRegister your product and get support atMCM2150Question?Contact PhilipsDownloaded From Disc-Player.com Philips Manuals
…
MCM2150(19 pages) |
Philips
MCM305/12© Copyright 2009 Philips Consumer Electronics B.V. Eindhoven, The NetherlandsAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.Published by SL 0920 Service Audio Pr …
MCM305/12(15 pages) |
CamTron Security Camera VRCD-5371VRCD-5371 Instruction manual - E83H95 VRCD-5371, 14 |
Toshiba Laptop M645-S4062Toshiba Product User Guide: M645-S4062 PDF Specifications - 7ERQ53 M645-S4062, 4 |
Mastervolt Camera Accessories MLI-E 12/1200MLI-E 12/1200 Operation & user’s manual - 8GLFJ3 MLI-E 12/1200, 24 |
Oleomac Camera Accessories ba 2,6 ahOperators instruction book for Oleomac ba 2,6 ah Camera Accessories ba 2,6 ah, 52 |
Makita Brush Cutter RBC280Brush Cutter PDF Instruction manual RBC280, 43 |
AT&T Telephone 76307630 Operation & user’s manual - 6TTW6H 7630, 35 |
Sapling Clock SMC 3000 SeriesClock Installation manual (Sapling SMC 3000 Series) SMC 3000 Series, 19 |
New Holland Lawn Mower G6030#37GZ75: G6030 Lawn Mower Specifications G6030, 2 |
Jenn-Air Cooktop 30" (76.2 CM)Use and care manual for Jenn-Air 30" (76.2 CM) Cooktop 30" (76.2 CM), 24 |
American Dynamics Security Camera ADCIPE3312ISNSecurity Camera Specifications (American Dynamics ADCIPE3312ISN) ADCIPE3312ISN, 24 |
Honda Engine GXH50GXH50 Owner's manual - 3H4865 GXH50, 48 |
Living Water Hot Tub St. Lucia SeriesPDF Guide (@Q9O23E), Living Water St. Lucia Series Hot Tub (16/12/2023) St. Lucia Series, 50 |