Manualios.com

Autoleads ADI-100 Operation & User’s Manual

Autoleads ADI-100 Manual Online:

4.3, 2285 votes
Autoleads ADI-100 User Manual
Autoleads ADI-100 User Guide
Autoleads ADI-100 Online Manual

Text of Autoleads ADI-100 User Guide:

  • Autoleads ADI-100, 28 u On the ADI-100 enter the menu function, the screen will show ( 87.6MHz ), then press Rotary Knob to reset FM transmitting frequency to 87.6MHz or; u Press and hold BACK twice in succession to reset FM transmitting frequency to 87.6MHz. To Reset to a frequency that has been saved in FM frequency preset 1 do the following u On your Car Radio press the FM preset of your car radio that corresponds to the same frequency as in ADI-100’s FM f

  • Autoleads ADI-100, 29 u Digital Audio Services: DAB/DAB+. u RF Frequency Range: DAB Band III (174 MHz ~ 240 MHz). u RF Sensitivity for DAB Band III: -98dBm ~ -100dBm. u FM Transmit Range: 87.6 MHz ~ 107.9 MHz. u Mains Power: 11 V ~16V DC u Input Connectors: DC power jack, 3.5mm stereo audio jack. u Presets: 4 DAB station presets (for each DAB mode) and 4 FM transmit presets. u Operating Temperature Range: -10°c ~ +70°c. u Storage Temperature Range: -40°c ~ +85°c. u DAB Antenna Connector: -

  • Autoleads ADI-100, 20 4. Press FM preset of your car radio corresponds to the same frequency from step 2 if you have previously saved for DAB reception. Otherwise, tune the car radio to the same FM frequency. 5. Now you can listen to DAB stations via this new FM Frequency. To Force Immediate FM Transmitting Frequency Change This function can be used in either AFC or AutoScan mode to force a FM transmission fre- quency change immediately. In AFC_H or AFC_L Mode While listening to a DAB station, if you hear static nois

  • Autoleads ADI-100, 8 Installation ‘Do’s & Don’t’s’ - continued 1. Do not tangle the antenna and power cables together. 2. Minimize coiling loops of excessive power cable or antenna cable, and do not secure them on or besides ADI-100. The coiling loops of excessive power or antenna cables should start at about 10 cm away from the ADI-100  

  • 21 Operating on ADI-100 1. Press and hold LINK, the screen will show ( TO Frequency ) where Frequency is the new frequency that ADI-100 will set and use to transmit FM signal. Operating on Car Radio 1. Manually change your car radio’s FM frequency to match the new ADI-100 transmitting frequency setup. To Set FM Transmitting Frequency Setting to Preset

  • Autoleads ADI-100, 12 STARTING UP THE SYSTEM 1. Turn on your in-car audio system. 2. Enable the AF function on your car radio if it is equipped (Consult your car radio manual or the car dealer if your car radio has AF feature, and how to enable AF feature). 3. Tune the car radio’s FM frequency to FM 87.6MHz, which is the same as ADI-100 default FM TX frequency. 4. Start ADI-100 by plugging the cigarette-lighter power plug into the cigarette lighter, the audio system di

  • Autoleads ADI-100, 22 MENU SETTINGS You must press the Rotary Knob then MENU button to enter the menu function, rotate the Rotary Knob (t) / (u) to select a menu setting, and then press the Rotary Knob to conrm the selection. To Reset FM Transmitting Frequency Setting This function allows you to reset the FM transmitting frequency to the default setting FM 87.6MHz. 1. Reset ADI-100’s FM transmitting frequency by either way below: a. Enter the menu function, the screen will show ( 87.6MHz ). Then, Press the Rotary Knob to reset FM transmitting frequency to 87.6MHz. b. Press and hold BACK twice in succession to reset FM transmitting frequency to 87.6MHz. 2. Press FM

  • Autoleads ADI-100, 6 Installation Procedure (continued) 4. Secure ADI-100 with the supplied dual lock tapes and screws. Please refer to the section on Securing ADI-100, Step by Step. 5. Minimize coiling loops of excessive power cable and antenna cable, and do not secure them on ADI-100. Please refer to section on Installation do and don’t. 6. Plug one end of the power cable to ADI-100, and the cigarette-lighter plug into car’s cigarette lighter. There is a lock mechanism on the plug of Power Cable to ADI-100. First, plug the power cable into the 12V DC jack (1), and then you need to turn the power plug 90 degree clockwise (2) as illustrated below. This

  • 23 To Enable AFC (Automatic Frequency Change) If your car radio does not have AF feature then please refer to To Enable AutoScan. It may become necessary to change the FM transmitting frequency as you drive into an area where the FM frequency transmitted by ADI-100 is used by an FM broadcaster. ADI-100 has an AFC function that allows you to continuously li

  • 9 OPERATIONAL CONTROLS In-Car Audio System LCD Display The ADI-100 unit is operated by using a remote controller; the system messages from the remote control operation are converted to RDS text and displayed as 8 characters display on the LCD screen of your in-car audio system. Below is a list of ADI-100 system messages displayed on the in-car audio system LCD display, while operating with th

  • Autoleads ADI-100, 25 To Enable RC Beep Tone When you enable RC beep tone, ADI-100 will respond with a beep tone, each time an operation is performed on the remote control. 1. In the menu function, rotate the Rotary Knob (t) / (u) until the screen shows ( RC BEEP ). 2. Press the Rotary Knob to enter RC beep tone selection operation. 3. Then you can rotate the Rotary Knob (t) / (u) until the screen shows ( BEEP ON ) to enable the RC beep tone. 4. Or you can rotate the Rotary Knob (t) / (u) until the screen shows ( BEEP OFF ) to disable the RC beep tone. 5. Finally, press the Rotary Knob to set the RC beep ton

  • Autoleads ADI-100, 15 To set a DAB Preset Mode The ADI-100 provides individual memory settings for up to three sets of DAB Preset Modes: DAB1, DAB2, and DAB3. Each DAB Preset Mode has its own Memory Presets of DAB stations; please refer to To Save a DAB Memory Preset and To Recall a DAB Memory Preset sections below. This allows user to setup three DAB Presets for different users (driver or passengers) or different group of stations to enjoy the favorite programs based on the individual settings. 1. Press the Rotary Knob and then DAB to enter t

  • Autoleads ADI-100, 14 Step Tune 1. Rotate the Rotary Knob (t) / (u) to step through the stations, one by one, until the screen shows the desired station: ( station name ). ADI-100 will start tuning to the selected station immediately. Quick Tune 1. Accelerate Rotating the Rotary Knob (t) / (u) to quickly tune to the rst station in the previous/next alphabet. Repeat the action, one alphabet at a time, until the screen shows the DAB station with desired initial alphabet. 2. Perform the Step Tune to

  • Autoleads ADI-100, 27 To Upgrade Software This function is used by the maintenance personnel only, to upgrade the existing ADI-100 module software to a new version. TROUBLESHOOTING Please read this user manual carefully before using the ADI-100 In-Car DAB Adapter. If you still have difculties to use this unit, this section gives some of the most likely solutions to the problems you might have. u I cannot nd any DAB stations. Ensure that DAB coverage exists in your area. Please visit www.worlddab.org or www.digitalradionow.com to check for DAB coverage. u I can nd DAB stations, but I cannot

  • Autoleads ADI-100, 26 To Perform DAB Reset 1. In the menu function, rotate the Rotary Knob (t) / (u) until the screen shows ( DABRESET ). 2. Press the Rotary Knob to perform a reset operation for DAB Presets. 3. If you do want to reset, rotate the Rotary Knob (t) / (u) to nd ( YES ) and then press the Rotary Knob for conrmation. Otherwise, you can press the Rotary Knob to cancel while the screen is showing ( NO ). The screen will show ( RESETING ) to indicate that DAB reset is in progress. Note: DAB reset will erase the station list but keep the memor

  • Autoleads ADI-100, Autoleads is a brand of Armour Automotive Unit 25, Woolmer Way, Bordon, GU35 9QZ +44(0)1420 476767 - [email protected] www.autoleads.co.uk - www.armourauto.com This radio is future-ready because it contains DAB, FM and DAB+ which is a future technology standard being adopted across Europe

  • Autoleads ADI-100, 19 To Save a Desired FM Transmitting Frequency in Memory As unused FM frequency may vary from one area to another, it is suggested to save a few frequencies (up to 4 frequencies) in ADI-100 so that you can switch to a new FM transmitting frequency instantly when you drive into an area where the original FM frequency for DAB is no longer available. 1. Press LINK, and the screen will show the current FM Transmitting Frequency ( Frequency ). 2. Then you can rotate the Rotary Knob (t) / (u) to step up or down FM frequency by 100KHz, to choose a frequency, and the screen will show ( Frequency ). where Frequenc

  • Autoleads ADI-100, 3 Introduction The ADI-100 is an in-car audio adapter that offers a exible and cost effective way to ap- ply modern digital audio technology to your existing analogue in-car audio system. The existing analogue system can be easily upgraded to receive DAB/DAB+ digital radio services. ADI-100 uses FM-RDS micro-transmitter and no complex cabling to your car au- dio system. The ADI-100 DAB receiver is operated using a remote controller, while all mes- sages related to the system’s operations, such as service name, memory preset, etc., are converted to RDS text and displayed

  • Autoleads ADI-100, 18 3. Press the Rotary Knob or after a 10 seconds timeout, the FM transmitter will set and transmit FM signal at the new frequency. Now you can listen to DAB stations via this FM frequency. Operating on Car Radio 1. Manually change your car radio’s FM frequency to match the new ADI-100 transmitting frequency setup. To set FM Transmitting Frequency Manually If you wish to change the setting and use your own selected FM transmitting frequency manually, do the following: 1. Press LINK, and the screen will show the current FM Transmitting Frequency ( Frequency ). 2. Then you can accelerate rotating the Rotary Knob (t) / (u) to step up or down FM freq

  • Autoleads ADI-100, 10 Remote Control Please refer to next sections, USING REMOTE CONTROL KEYS, MENU SETTINGS, and FM TRANSMITTING FREQUENCY SETTINGS for detail description of each operation. Control Key General Operation Rotary Knob Press u Turn on ADI-100 while it is off. u Conrm a selection. u Change station information while listening to a DAB station. u Press and followed by AUX, DAB, SCAN, or MENU to enter the selected function mode. Press and Hold u Turn off ADI-100 while it is on. Rotate (t) / (u) u Step tune to select a DAB station. u Navigate to items, sub items, and settings after MENU is pressed. u Adjust FM tr

  • Autoleads ADI-100, 7 7. Start using ADI-100 with the remote control, please refer to the sections on OPERATION CONTROLS and STARTING UP THE SYSTEM. Securing ADI-100, Step by Step To secure ADI-100 on a chosen store location using the supplied dual lock tapes and/or screws, do the following: 1. Locate the positions on the back of ADI-100 and the chosen mounting location (e.g. in the middle and under the car’s glove compartment) where you want to apply the dual lock tapes. 2. Clean both surfaces with alcohol if avaiable and wipe dry before you start. Afx the tape on the ADI-100 and the chose mounting location 3. Remove one s

  • Autoleads ADI-100, 11 Control Key General Operation P2 SCAN Press u Recall memory preset P2. Press and Hold u Program memory preset P2 while listening to a DAB station. Function SCAN u Perform a full scan for DAB stations. P3 DAB Press u Recall memory preset P3. Press and Hold u Program memory preset P3 while listening to a DAB station. Function DAB u Set ADI-100 to one of the 3 DAB preset modes to listen to DAB. P4 MENU Press u Recall memory preset P4. Press and Hold u Program memory preset P4 while listening to a DAB station. Function MENU u 87.6MHz – Defa

  • Autoleads ADI-100, 24 Attention The ADI-100 comes with the AFC function. In order to use this function, your car radio must have AF (alternative frequency) feature, and AF must be enabled. Please consult your car radio manual or the car dealer for these requirements before using this function. While working with the AFC function, the possible factors that could affect its normal operation are: 1. The FM sensitivity varies among car radios and the sensitivity can affect AFC’s performance. 2. The algorithm implemented in each car radio’s AF feature varies and this can affect radio’s FM frequency tuning when triggered by AFC. If AFC function is unable to function norma

Related Products and Documents (Car Stereo System):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Lexmark W810 Service manual lexmark/w810-5J8.pdf 06 Oct 2022 489
2 GE Cafe Dimension and installation manual ge/cafe-G61.pdf 31 Mar 2023 2
3 Garmin GPS 19x HVS Installation instructions manual garmin/gps-19x-hvs-FH6.pdf 10 May 2023 56 5 Mb
4 Canon POWERSHOT A85 Quick start manual canon/powershot-a85-236.pdf 24 Sep 2023 318
5 Star FVP-10U Specifications star/fvp-10u-W9S.pdf 28 Feb 2023 2 0.26 Mb
6 Klutch 39108 Owner's manual klutch/39108-5U5.pdf 13 Feb 2024 13

Similar Resources:

  • Clarion

    DB345MP

    (23 pages)
    - 1 -- 1 -- 1 -- 1 -- 1 -DB345MP/DB346MPDB345MP/DB346MPDB345MP/DB346MPDB345MP/DB346MPDB345MP/DB346MPSeSeSeSeServrvrvrvrvice Manualice Manualice Manualice Manualice ManualPublished by Clarion (Malaysia)298-6124-00 FEB. 2004PPrinted In MalaysiaClarion ( Malaysia) Sdn. Bhd.Clarion ( Malaysia) Sdn. Bhd.Clarion ( Malaysia) Sdn. Bhd.Clarion ( Malaysia) Sdn. Bhd.Cl …
  • JVC

    CS-V418

    (4 pages)
    Speakersdrvn Series SpeakersThe woofer’s lighter and more flexible Carbon Mica cone and Hybrid Surround with improved shape allow smoother movements for superior bass delivery. As for the tweeter, the improved PEI diaphragm and the ornament design provide better sound quality for the vocal frequency range as well as enhanced spreading of sound. The aggress …
  • JVC

    KV-MR9000

    (15 pages)
    ENGLISHDEUTSCHFRANÇAIS* This system cannot receive television broadcasts and is primarilydesigned for use with a VCR or a DVD player. Use the separately soldmobile TV tuner unit KV-C10 for optional television broadcast reception.* Dieses System kann keine Fernsehsignale empfangen und wurde inerster Linie für die Verwendung mit einem Videorecorder oder eine …
  • Sony

    CDX-GT650UI - Fm/am Compact Disc Player

    (2 pages)
    Notes on the control and power supply leadsThe power antenna (aerial) control lead (blue) supplies +12 V DC when you turn on the tuner.When your car has built-in FM/AM antenna (aerial) in the rear/side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing anten …
  • Philips

    DC570

    (2 pages)
    PhilipsDocking Entertainment SystemDC570Enjoy iPod music out loud in superb soundwith speaker towerThe ultra-stylish Philips Docking Entertainment System DC570 fills any room with your favourite iPod tunes. Elegantly designed to take up minimal space, the sleek system delivers unbelievably powerful Hi-Fi sound from its built-in subwoofer.Enrich your sound …
  • JVC

    KD-S8R

    (20 pages)
    SERVICE MANUALCD RECEIVERNo.49572Sep. 2000COPYRIGHT 2000 VICTOR COMPANY OF JAPAN, LTD.KD-S8RKD-S8R Area SuffixE ------ Continental EuropeEX ---- Central EuropeThis service manual is printed on 100% recycled paper.KD-S8R is a change model of KD-S777. Additionally, please refer to KD-S777 (service manual issue No.49542) because the service manua …

Comments, Questions and Opinions: