Fujitsu Rugged Tablet Case Operation & User’s Manual

Text of Fujitsu Rugged Tablet Case User Guide:

• Fujitsu Rugged Tablet Case, These instructions provide details on using the rugged tablet case with your Fujitsu LifeBook notebook when it is in tablet mode. The case provides added protec- tion when transporting, using, or storing the note- book. We recommend that you read these instructions prior to using the case with your computer. Package Contents Included in the package are the following items: ■ Rugged tablet case ■ Full-size pen (designed to fit in the pen holder on the front of the case. This pen will not fit in the pen holder that is built into the system.) ■ Pen tether ■ Hand strap (2 pieces) ■ Case handle ■ Shoulder

• Fujitsu Rugged Tablet Case, 2 Figure 1. Rugged tablet case - Front * Use the pen which came with the case in the pen holder. See note above. The pen which came with the system is too small to fit snugly in the pen slot, so a full-size pen is included with the case. The pen holder on the top front of the case should be used to store the pen. When the system is in the case, the system pen slot is not accessible. (Figure 1) Pen Holder* Port/slot access Application Fingerprint sensor access button access System status/ power/suspend/ resume button access D-rings (2 places} Built-in microphone access Rugged Case - Chalice .fm Page 2 Monday, March 19, 2007 10:09 AM

• Fujitsu Rugged Tablet Case, 3 Figure 2. Rugged tablet case - back Installing the hand strap The hand strap is designed to let you hold your system securely when it is installed in the case. Use of the hand strap is highly recommended. The hand strap consists of two parts, each of which has a Velcro strip on one end and a retaining bar at the other. Note that the longer of the two strips (with the “fuzzy” Velcro) should be positioned in the top slot, while the shorter strip (with the “hooks” Velcro) should be inserted in the bottom slot. To install the hand st

• 4 2. Insert the shorter of the two pieces of the hand strap into the bottom slots with the Velcro “hooks” strip fac- ing up. (Figure 3) Pull it through until the retaining bar is snug against the case. Figure 3. Inserting hand strap halves 3. Insert the longer piece of the hand strap into the top slot with the “fuzzy” Velcro strip facing down (Figure 3). Pull it through unt

• Fujitsu Rugged Tablet Case, 5 Installing the system To install your system into the rugged tablet case, perform the following steps: 1. Position the case face down (the same orientation as when you installed the hand strap). 2. Position the system in tablet mode with the display fac- ing down, and hold it by the edge opposite the battery. Figure 4. Inserting the system in the case 3. Insert the battery edge of the system into the wide, rigid edge of the case (the side with the D-rings). Push it in until it is flush with the

• Fujitsu Rugged Tablet Case, 7 Using the hand strap When you want to hold the case using the elastic hand strap, first separate the two halves. Place your hand in a comfort- able position on the bottom of the system and re-secure the strap against the back of your hand. When not using the hand strap, attach it snugly against the back of the computer. Installing the handle To install the handle, perform the following steps: 1. Insert one end of the handle into the D-ring, with the buckle facing outwards (Figure 7). Figure 7. Inserting handle strap 2. Bend the end of the handle strap towards the buckle and tuck it under the edge of the buckle (Figure 8). 3. Pull

• Fujitsu Rugged Tablet Case, 8 5. Repeat the procedure above with the other end of the handle. Figure 8. Inserting strap into buckle. Figure 9. Pulling strap through buckle Rugged Case - Chalice .fm Page 8 Monday, March 19, 2007 10:09 AM

• Fujitsu Rugged Tablet Case, 9 Figure 10. Tightening the strap Installing the shoulder strap To install the shoulder strap, open the spring-loaded clips on both ends and attach one to each of the D-rings (Figure 11). Figure 11. Installing the shoulder strap Rugged Case - Chalice .fm Page 9 Monday, March 19, 2007 10:09 AM

• Fujitsu Rugged Tablet Case, 10 Installing the pen tether To install the pen tether, insert one end into one of the D- rings, then feed it through the loop on the other end. Pull it snug against the D-ring. Feed the loose end of the tether through the hole on the end of the pen, slide the loop over the tip of the pen, then down the barrel. Pull it snugly to tighten the loop. Caring for the rugged tablet case The case is made of rugged materials, and is designed to withstand daily use. Treat the case as you would a briefcase or purse. Occasionally, the case may become soiled. To c

• 12 1250 E. Arques Avenue (M/S 122), Sunnyvale, California 94085 For more information, call 1-877-372-3473 or visit our Web site at: us.fujitsu.com/computers For technical support call: 1-800-8fujitsu (1-800-838-5487) or e-mail us at: [email protected] Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu, Ltd. All other trademarks mentioned herein are the property o

Related Products and Documents (Carrying Case):

Comparable Devices:

Similar Resources:

• Hypertec BacPac Broker N9608NHY (1 pages) A notebook backpack with a business lookWith its professional look the ergonomic BacPac Broker is the ultimate business alternative to a sporty notebook backpack. The unusual form as well as its black & silver grey colour combination make it extremely attractive. The spacious document compartment offers room for documents, power supply units, and other …

• Hypertec 3103 (1 pages) Series 3 3103 Our patented air-cell protection. Surrounded by interconnected pockets of compressed air, your laptop is safeguarded against vibrations and shocks. A unique world-wide tracking system. Unique i-TRAK™ codes make your luggage and laptop unique and identifiable if you lose or forget them. Series 5 and above An adjustable laptop co …

• Fujitsu FMWCC38 (1 pages) Stylistic LT is a trademark of Fujitsu Personal Systems, Inc. © 1999 Fujitsu Personal Systems, Inc.6/99 Page 1 of 1 58-0666-00AFMWCC38Carrying CaseUser’s InstructionsStylistic LTThese instructions provide details on using the FMWCC38 carrying case with your Stylistic LT pen tablet computer. When used with the Stylistic LT, the carrying case provides add …

• Tektronix HCTEK54 (2 pages) xx HCTEK54 Transit CaseThe HCTEK54 is a ruggedized transit case specificallydesigned to provide travel and storage protection. The caseprotects instruments from shock, vibration, and moisture withroom for accessories, such as probes, adapters, and manuals.The HCTEK54 case accommodates the following productseries:MSO4000B, DPO4000B SeriesMSO5000, DPO5000 Ser …

• HP 381513-B21 - Smart Array P800 Controller RAID (15 pages) Redundancy in enterprise storage networks using dual-domain SAS configurations technology brief Abstract.............................................................................................................................................. 2 Introduction................................................................................................. …

• HP 245161-B22 - 10642 42U Rack Shock Pallet (3 pages) HP 10000 Series Rack Airflow Optimization Kit Installation Instructions Overview The HP 10000 Series Rack Airflow Optimization Kit enables you to install foam rail gaskets into your HP 10000 G2 Series 22U, 36U, 42U, and 47U 600-mm (24 in) wide racks and into 42U 800-mm (31 in) wide racks to improve separation between hot and cold aisles in the data ce …

Comments, Questions and Opinions: