Syscom Video EPMON19LED Operation & User’s Manual

Text of Syscom Video EPMON19LED User Guide:

• 1 Introduction and Package Contents Introduction Congratulations on your purchase. You can expect only the sharpest and most brilliant color images from this monitor. Featuring easy to use OSD controls and built in speakers, you will find this monitor both easy to use and a pleasure to look at. Please unpack the monitor with care, and verify that all the parts listed below are included. If an

• Syscom Video EPMON19LED, 32” Specifications for 19 “ Size EPMON19LED Composite Output (BNC) x 2 Composite Input (BNC) x 2 Single Connector (VGA) x 1, (RCA) x 2 (PC Audio) x 1, (HDMI) x 1 Speaker 1.5W x 2 Display Mode Video 1/ Video 2/ PC/ HDMI AC power AC 100~240V 50/60Hz Temperature Operation: 0°~40°C(32° ~104°F) , Storage: -10°~60°C(14° ~140°F) Power Consumption 25W Max. in “ON” Mode Under 3W in Power Saving Mode (100 Vac) Under 5W in Power Saving Mode (240 Vac) OSD Control Picture Mode, Contrast, Brightness, Color, Tint, Sharpness, Color Temp, DNR OSD Languages English, German, French, Itali

• Syscom Video EPMON19LED, Specifications for 23.6 Model EPMON23LED Composite Output (BNC) x 2 Composite Input (BNC) x 2 Single Connector (VGA) x 1, (RCA) x 2 (PC Audio) x 1, (HDMI) x 1 Speaker 1.5W x 2 Display Mode Video 1/ Video 2/ PC/ HDMI AC power AC 100~240V 50/60Hz Temperature Operation: 0°~40°C(32° ~104°F) , Storage: -10°~60°C(14° ~140°F) Power Consumption 35W Max. in “ON” Mode Under 3W in Power Saving Mode (100 Vac) Under 5W in Power Saving Mode (240 Vac) OSD Control Picture Mode, Contrast, Brightness, Color, Tint, Sharpness, Color Temp, DNR OSD Languages English, German, French, Italian, Spanish, Russian, Turkish, Polish, Dutch, Czec

• Syscom Video EPMON19LED, Specifications for 32 Model EPMON32LED Diagonal size 32" Panel type TFT LCD Aspect ratio 16:9 Number of pixels 1920 x 1080 Pixel pitch (H x V) 0.12125 x 0.36375 mm Color depth 16.7 Million Colors Backlight LED Brightness 400 cd/m2 Contrast ratio 5000:1 Response time ( Tr + Tf) 8.5 ms Viewing angle Vertical -88°~88° , Horizontal -88°~88° Input Interface BNC x 2, VGA x 1, HDMI x 1, RCA x 2, PC Audio x 1 Output Interface BNC x 2 Display mode Video 1 / Video 2 / PC / HDMI OSD Picture Mode, Contrast, Brightness, Color, Tint, Sharpness, Color Temp, DNR OSD Languages English, German, French, Italian, Spanish, Russian, Turkish, Polish, Dutch, Czech Additional mo

• Syscom Video EPMON19LED, Accessories Monitor, Power cord, VGA cable, User Manual, Remote controller VGA Timing Item Resolution H Freq.(kHz) V Freq.(Hz) 1 640x400@70 31.460 70.080 2 640x480@60 31.469 59.940 3 640x480@72 37.861 72.809 4 640x480@75 37.500 75.000 5 720x400@70 31.460 70.080 6 800x600@56 35.156 56.250 7 800x600@60 37.879 60.317 8 800x600@72 48.077 72.188 9 800x600@75 46.875 75.000 10 1024x768@60 48.363 60.004 11 1024x768@70 56.476 70.069 12 1024x768@75 60.023 75.029 13 1280x1024@60 63.981 60.020 14 1280x1024@75 79.976 75.025 15 1920x1080@60 ( 21.5”) 67.500 60.000

• Syscom Video EPMON19LED, Features – AC 100-240V Power Supply – NTSC/PAL Auto Detect – High Resolution Display 1280 x 1024 – VGA Input – Composite Video Input – HDMI Input – On-screen Display (OSD) with Multiple Languages – PIP / POP Function Quick Installation 1. Connect power cord and power adaptor. 1 2. Connect video cable • Make sure both the LED display and computer are turned off. • Connect the video cable from the LED display to the computer. 1 3. Turn ON LED display and computer 4. Select input source • Select the proper input source corresponding to the video Signal, AV1/ AV2 / VGA / HDM

• M S A Menu Select - + Auto Power - Menu Selec t - + Aut o Power The LED color monitor has a simple control layout for controlling the monitor and OSD (On Screen Display) functions. The table below summarizes the control keys and their related functions. 5-Key Feature Keys Function Description Power Toggle the display between standby mode and on. (Press “Power” and waiting 6 sec., mon

• Illustration of the remote controller (For 21.5” ) POWER SWITCH MENU VOLUME – / Switch setting item VOLUME + / Switch setting item VIDEO – Switch to AV1/AV2/ HDMI/VGA MODE – Source menu / switch setting item Remote Controller (Only for 32” LED Monitor)

• Syscom Video EPMON19LED, Source Select Press the S / Select button to bring up source selection Use the (－)OR (＋) keys to advance to the proper selection and press S / Select button to confirm the setting. Note: The message will be displayed on the screen if there’s no VGA signal detected in VGA mode, and the power will be off automatically after 10 seconds. Please press the power button again to restart the monitor. LED Status Display The following table describes the various power states of the LED monitor as represented by differe

• Note: The LED will also be red if AV1 or AV2 is selected and there is no video signal detected. OSD Menu Picture Mode 1. Picture Mode Press (－)OR (＋) to select the picture mode “User, Standard, Movie, Vivid ” 2. Contrast This is used to set the brightness of the screen. Press (－)OR (＋) to adjust the parameter. 3. Brightness This is

• Syscom Video EPMON19LED, 1. Volume Press (－)OR (＋) to adjust volume level. 2. Mute Press (－)OR (＋) to select sound “ Off, On ”. Setting Mode 1. Language Press (－)OR (＋) to select language. 2. H. Position Move the display picture left or right. Press (－)OR (＋) to adjust the parameter. 3. H Zoom Adjust the H-size of the display picture Press (－)OR (＋) to adjust the parameter. 4. V Position Move the display picture up or down. Press (－)OR (＋) to adjust the parameter. 5.

• Syscom Video EPMON19LED, Press (－)OR (＋) to adjust “ Full, 16:9 ”. 9. Reset Recall Default value. Note: “ Clock” and “Phase ” setting only in VGA Mode PIP/POP Setup Mode 1. Multi Window Press (－)OR (＋) to select “PIP, POP, Off ” mode. 2. Sub Source Press (－)OR (＋) to select “AV, VGA” mode. 3. Size Adjust the size of Sub Source window. Press (－)OR (＋) to select “Large, Small ” 4. Position Mov

• Syscom Video EPMON19LED, 4 Mounting VESA Bracket Lay the LED display face down on a towel or blanket. Note the 4 screws that secure the hinge on the lower part of the back casing. These may be removed to release the desk mount bracket if required. Attach a VESA compatible mounting bracket VESA 75mm x 75mm (for 17” and 19”) ; VESA 100mm x 100mm (for 21.5” and 23.6”) 1DUSCL1B-A.0 13 4 scr ew f or VESA mount

• Syscom Video EPMON19LED, Caring for your LED Monitor The LED color monitor is a sensitive piece of electronic equipment. Proper care can prevent accidentally damaging the LED panel or the monitor itself. By following these guidelines you can ensure many years of trouble free use. 1. The LED monitor's plastic casing and LED glass panel can be cleaned with a soft, lint-free cloth. Never use scrub pads or other cleaning materials with abrasive surfaces to clean your LED monitor! a. For the plastic case, a mild detergent may be used to clean the surface. However, you should ensure not to use too much detergent or water as this could leak into the interior of the casing. 2. D

• Syscom Video EPMON19LED, WARNING: Any unauthorized modification to this equipment could result in the revocation of the authorization to operate the equipment and void the product warranty. 7 Frequently Asked Questions Power button does not respond  Check the power cord to ensure that it is securely plugged into the monitor base and also into the electrical outlet.  Ensure there is electrical power coming from the AC outlet. Use another device to check for power.  Unplug the power cord of the monitor from

• Syscom Video EPMON19LED,  Inspect the audio cable for any apparent damage. Double check by switching to another audio cable to see if the audio works. 8 Regulations and Maintenance FCC compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

• Syscom Video EPMON19LED, ＊ Product - Do not cover or block the vent holes in the case. - Do not insert sharp objects or spill liquid into the LED monitor through cabinet slots. They may cause accident fire, electric shock or failure. - Disconnect the power plug from the AC outlet if you will not use it for an indefinite period of time. - Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials or other risks. - Do not touch the screen directly with your fingers. You may damage the screen, and oil from your skin is difficult to move. - Do not apply pressure to the screen. The LED is very delicate. ＊ Power - Us

• Syscom Video EPMON19LED, ＊ Power and extension cords - Do not allow anything to rest on the power cord. - Do not locate this product where persons will walk on her cord. - Use the proper power cord with correct attachment plug type. If the power source is 120 V AC, use a power cord that has UL and C-UL approvals. If the power source is a 240 V AC supply, use the tandem (T blade) type attachment plug with ground conductor power cord that meets the respective European country’s safety regulations, such as VDE for Germany. - Do not overload wall outlets or power cords. Ensure that the total of all units plu

Related Products and Documents (Security System Monitor):

Comparable Devices:

Similar Resources:

• F&V MeticaFM 7 (2 pages) For more information visit: fvlight.comF&V Photographic Industry B.V.Steenovenweg 5, 5708HN Helmond, NetherlandsTM & © F&V All rights reserved.Hardware UpgradeMeticaFM 7 Upgrade the hardware in your MeticaFM 7 to unlock additional software features such as: pattern generator, false color, range error, histogram, and audio columns.For upgrades, t …

• Sanyo VMC-8618 (16 pages) INSTRUCTION MANUALColor Video MonitorVMC-8618VMC-8613About this manual•Before installing and using this unit, please read this manual carefully. Be sure to keep it handy for later reference.•This manual gives basic connections and operating instructions for 2 models.L8MV5/US, L8MW5/US (VMC-8618, 8613 GB) 2001. 2. 23 …

• Digittrade HS128 (76 pages) DeutschBenutzerhandbuchUser ManualHigh Security HS128 / HS256Version 13.11.2012external encrypted HDD/SSDfür Unternehmen und Behördenfor enterprise and government use …

• Brigade VBV-750M (12 pages) VBV-750M vehicle CCTV monitorQuick installation guideGuide d’installation rapideKurzanleitungGuida d’installazione rapidaGuía rápida de instalaciónSnelle installatie handleidingGuia rápida de instalaçãoРуководство по быстрой установкеHızlı Montaj KlavuzuSkrócona instrukcja instalacjiPart Number 4367B …

• Speco VM1701B (1 pages) VM-1701B17” B/W MonitorSpecificationsResolution 1000 TV linesInput Impedance 75 ohm/high (switchable)Input Signal 0.5 to 2.0 VP-p composite videoInput Voltage 96~256V AC; EIA & CCIR; 60Hz/50HzLinearity +/- 10 % horizontal, +/- 10 % verticalScanning Frequency EIA standard 15.75 kHz horizontal, 48-62 Hz verticalVideo Gain 33 dBOperating Temperature 32˚ …

• SVAT CLEARVU11 (22 pages) SVAT ELECTRONICSnow you can seeCLEARVU11505. - Click on this icon to enable/mute the audio input from the PC, button down for enable, button up for mute. If enabled, the audio input from the PC will be sent to the DVR. The default setting is ‘mute’.6. - Click on this icon to enable/mute the audio output from the camera for the focus window, but …

Comments, Questions and Opinions: