Effekta MTD-XL Operating Manual

Text of Effekta MTD-XL User Guide:

• Effekta MTD-XL, UPS MTD-XL UPS Device Description MTD series 36 Procedure for the rotation of the display: 1 Snap lock 2 Display Fig. 3-3 - 2 Rotate display  Press the snap lock (1).  Pull the control panel (1) carefully forward and from the housing.  Rotate the display 90°, so that it fits properly for a horizontal set-up.  Push the display into the housing until it snaps into place. The display is connected through a flat ribbon cable. Do not pull the cable. 1 2

• Effekta MTD-XL, UPS MTD-XL Safety Instructions MTD series 17 2.5 Connection The UPS may only be connected to a grounded isolated ground recepta- cle or if connected via terminals, the protective earth conductor must be connected without fail. The device may not be used without the PE under any circumstances. The socket for the domestic installation must be easily accessible and in proximity to the UPS. Keep the cable length as short as possible in the case of permanent wiring. During generator operations the pole-correct connection of the UPS must be ensured. For the connection of the UPS to the socket of the domestic installation, only a power cable that is VDE-ap

• Effekta MTD-XL, UPS MTD-XL Maintenance and Service MTD series 70 11.3 Service-Log Please always enter all maintenance and service work conducted on the UPS into the service-log. Date Performed tasks Performed by

• Effekta MTD-XL, UPS MTD-XL UPS Device Description MTD series 25 LCD-Display-Text Description STbY The UPS is in standby mode. IPVL The input voltage is too low. IPVH The input voltage is too high. IPFL The input frequency is too low. IPFH The input frequency is too high. NORM The UPS operates in line mode. AVR The UPS operates in AVR mode. bATT The UPS operates in battery mode. TEST The UPS is in battery test / function mode. OPVH The output in battery mode is too high. OPVL The output in battery mode is too low. OPST

• Effekta MTD-XL, UPS MTD-XL Table of Contents MTD series 3 Table of Contents 1. Introduction ............................................................................................................... 5 1.1 Introduction ............................................................................................................... 5 1.2 Validity ...................................................................................................................... 6 1.3 Storage ..................................................................................................................... 6 1.4 Symbols in this Manual ............................

• Effekta MTD-XL, UPS MTD-XL UPS Device Description MTD series 47 1 Front panel 2 Cable feedthrough Fig. 3-4 - 4 Front panel - Cable feedthrough  At the front panel (1) of the UPS, as well as of the accumulator module you find cable feedthroughs (2) that are closed in the initial state, as delivered.  Carefully break the plastic parts of the cable feedthroughs (2) open with pliers and remove it from the front panel.  Make sure there are no sharp edges that could damage the cables.

• Effekta MTD-XL, UPS MTD-XL Safety Instructions MTD series 16 2.3 Avoiding Personal Injury / Property Damage  Please read this operating manual carefully to familiarise yourself with the device.  In particular, take note of the information regarding the installation and commissioning of the device.  Only operate the product in an appropriate and proper way and within the parameters stated in the technical data.  Only perform maintenance and service work that is described in the docu- mentation. Observe the required steps. Only use original replacement parts from EFFEKTA R

• UPS MTD-XL UPS Device Description MTD series 40 Procedure for the rotation of the display: 1 Snap lock 2 Display Fig. 3-3 - 2 Rotate display  Press the snap lock (1).  Pull the control panel (1) carefully forward and from the housing.  Rotate the display 90°, so that it fits properly for a horizontal set-up. 

• Effekta MTD-XL, UPS MTD-XL UPS Device Description MTD series 34 The shut-down signal must remain active for at least 20 ms, to ensure proper operation. 3.2.6 USB-port The USB-port serves to connect the UPS to a PC. 3.2.7 RS232-port The RS232-port serves to connect the UPS with a PC. 3.2.8 Input and output overvoltage protection Overvoltage protection for phone, fax or modem.

• Effekta MTD-XL, UPS MTD-XL UPS Device Description MTD series 39 3.3.2 Setting-up the UPS as a rack-mounted device Fig. 3-3 - 5 Rack-mounted device The following steps have to be taken:  Rotate the display to a horizontal position.  Fit the mounting brackets.  Mount the UPS in the slot of the 19" rack.

• Effekta MTD-XL, UPS MTD-XL UPS Device Description MTD series 30 3.2.3 Communication interface After unscrewing the cover, various additional expansion cards can be in- stalled, e.g. a relay card. Fig. 3-2 - 2 Network port (SNMP-slot-card)

• Effekta MTD-XL, UPS MTD-XL Legal notice MTD series 2 Legal notice  by EFFEKTA Regeltechnik GmbH EFFEKTA Regeltechnik GmbH, 78628 Rottweil, retains the copyright to this documentation. This documentation is solely intended for the operator and his staff. The con- tent of this documentation (texts, figures, drawings, graphics, plans, etc.) may not be copied or distributed in part or in full without our consent in writing, nor can it be used without authorisation for competitive purposes or given or made accessible

• Effekta MTD-XL, UPS MTD-XL UPS Device Description MTD series 27 3.2 Elements on the back of the device 1 UPS output 10A 2 Input overvoltage protection (RJ 45) 3 Output overvoltage protection (RJ 45) 4 Communication interface 5 Mains-input 6 "EPO"-port 7 USB-port 8 RS232-port Fig. 3-2 - 1 Back panel MTD-XL 1000 and 1500

• Effekta MTD-XL, UPS MTD-XL UPS Device Description MTD series 23 3.1 Elements on the front of the device On the front side of the device are all operating and display elements neces- sary for the normal operation of the UPS. 1 LCD-display 2 "Enter" button 3 "Select" button 4 "Alarm" button 5 "ON/ OFF"-button Fig. 3-1 - 1 Frontal view MTD-XL 1 5 4 3 2

• Effekta MTD-XL, UPS MTD-XL Commissioning of the UPS-System MTD series 64 8. Commissioning of the UPS-System To ensure proper fault-free commissioning, these steps have to be followed:  Connect the external battery module with the UPS.  Connect the UPS with the enclosed connection cable to the mains power supply.  Adjust the necessary settings on the UPS, like e.g. activation of outputs.  Connect the appliances with the UPS-outputs and switch to normal operat- ing mode.

• UPS MTD-XL System Description MTD series 52 If a mains failure continues beyond the backup time of the UPS, the UPS shuts down to avoid a total discharge of the accumulators. As soon as the mains power supply returns, the UPS automatically turns on again, supplies electricity to the appliance and controls the charging of the battery bank. Prominent performanc

• UPS MTD-XL UPS Device Description MTD series 24 3.1.1 LCD-display The LCD-Display shows the operating mode and a variety of status values. The following views can be selected with the help of the up and down buttons: Display Description Function Input frequency and voltage Shows the input frequency and voltage. Display inp

• Effekta MTD-XL, UPS MTD-XL UPS Device Description MTD series 26 3.1.2 Button ON / OFF button Please push the button for more than 3 seconds to turn the UPS on or off. To end the fault mode of the UPS, you have to disconnect the UPS from the input voltage and keep the ON / OFF button pressed for at least two seconds to turn off the UPS. UPS test / turning off an alarm To perform a basic functions test, keep the button pressed for at least 3 seconds. To perform a battery test, keep the button pressed for at least 10 seconds. To turn off a pending alarm, push the button for one second. Selection Press t

• UPS MTD-XL Introduction MTD series 14 1.8 Positioning Do not install in an area in which combustible vapours arise e.g. from petrol tanks, engine compartments, etc. The UPS is designed for operation in ventilated rooms with an ambient tem- perature of 0° to 40°C. If the UPS is exposed to severe and quick temperature changes, there is dan- ger

• UPS MTD-XL Introduction MTD series 6 1.2 Validity The descriptions in this operating manual relate solely to the uninterruptible power supply defined in the technical data as a whole or as it refers to modules, components and individual parts that were developed and built by EFFEKTA Regeltechnik GmbH.  12. Technical Data 1.3 Storage This operating manual fo

• Effekta MTD-XL, UPS MTD-XL UPS Installation and Connection MTD series 55 1 Mains power supply 2 10 A (for type 1000 / 1500) 16 A (for type 2000 / 3000) 3 0,75 mm 2 (for type 1000 / 1500) 1,5mm² (for type 2000 / 3000) 4 Load 1 5 Load 2 Fig. 6-1 - 1 Connection of UPS and appliances MTD series 1000 / 1500 2000 / 3000 S: 10 A 16 A 1: 0,75 mm 2 1,5 mm² 6.2 UPS communication port The UPS is equipped with a convenient communication interface to facilitate the exchan

• Effekta MTD-XL, UPS MTD-XL System Description MTD series 51 5. System Description The UPS provides an uninterruptible one-phase voltage for operations critical appliances. In addition to providing power to the appliance, it also maintains the internal accumulators in charged condition. In the case of a mains failure or interference (e.g. due to voltage fluctuation), the UPS continues to provide a clean supply voltage from the UPS-output without interruption. During the backup mode, power is provided from the battery bank. 1 Mains Input 7 Control pa

• Effekta MTD-XL, UPS MTD-XL UPS Device Description MTD series 21 3. UPS Device Description This manual shall provide basic information about one-phase line-interactive UPS-systems, like the mode of operation, utilization of the different functions and what to do in case of malfunctions. In addition, this manual contains instructions for the proper transportation and storage, as well as for the handling and installation of the UPS-equipment. The planning guidelines in this manual refer only to the specific requirements of UPS-systems. National and regional regulations for electrical installations have to be adhered to, when installing the system. The content of this

• Effekta MTD-XL, UPS MTD-XL UPS Installation and Connection MTD series 53 6. UPS Installation and Connection All requirements listed in the technical specifications concerning ambient and operating conditions must be met, to ensure proper operation of the UPS. Please note the following during set-up / installation of the UPS:  Avoid extreme temperatures and humidity.  Ensure proper horizontal set-up.  Allow adequate space for ventilation of the device. Ensure a proper flow channel.  Pay att

• Effekta MTD-XL, UPS MTD-XL Troubleshooting MTD series 65 9. Troubleshooting Only authorized trained personnel may perform troubleshooting tasks on the UPS. Fault Cause Measures Alarm signal in 4 seconds intervals The UPS is in battery mode. Check the mains power supply input. Alarm signal every second and the mes- sage "bATL" appears on the display. The battery voltage is too low. Save all data of the appliances and switch these of. Charge the battery for 24 hours. Alarm signal every second

Related Products and Documents (UPS):

Comparable Devices:

Similar Resources:

• Dell 1000W (73 pages) Dellt Line-Interactive Rack UPS1000W, 1920/1500W, and 2700/2300WUser's GuideH919N, J718N, K792N, H928N, K802N, H945N, J727NJ735N, K811Nw w w . d e l l . c o m | s u p p o r t . d e l l . c o m …

• Xtreme G90 (54 pages) G90 Online UPS1000VA, 2000VA, 3000VA ModelsUser & Installaon Manualwww.xpcc.com | © 2015 Xtreme Power Conversion Corporaon. All rights reserved. (Rev 2/5/15) …

• Online USV XANTO 700 (8 pages) ONLINE USV-Systeme AG – Luise-Ullrich-Straße 8 – 82031 Grünwald / Germany - www.online-usv.de ONLINE USV-Systems S.r.l. - Via Ferruccio Gilera 110 - I-20862 Arcore (MB) - www.online-ups.it ONLINE USV-Systeme AG – c/o POTESTA AG - Hertistrasse 29 - 8304 Wallisellen (Zürich) - www.online-usv.ch \X700-3000_quickstart-saftety_ger-engl-it_final_2 …

• Rittal PMC12 (32 pages) Rittal PMC12 UPS – User Manual 1phase UPS-System with online-double-conversion technology Powerrange 1 - 3 kVA (Art.-Nr. 7857.430, 7857.431, 7857.432, 7857.482, 7857.483) FRIEDHELM LOH GROUP R i t t a l GmbH & Co. KG Auf dem Stützelberg D – 3 5 7 4 5 H e r b o r n Germany Email: [email protected] http://w …

• Tripp Lite AVRX750UF (40 pages) 1Owner’s ManualAVR Series UPS SystemsImportant Safety Instructions 2Features 3Installation 6Optional Installation 6Troubleshooting 7Storage & Service 7Español 9Français 17Deutsche 25Ðóññêèé 331111 W. 35th Street, Chicago, IL 60609 USAwww.tripplite.com/supportCopyright © 2010 Tripp Lite. All rights reserved.AVRX550UF AVRX550UD AVRX55 …

• Njoy Protector 801 (3 pages) User Manual n’Joy Protector 801 650VA / 325Watts Step-Sine Wave Thank you for purchasing our product. Please read the USER’S MANUAL before using the product. The UPS will protect your electronic equipment from physical damage and will provide emergency battery backup power to prevent data loss in the event of power problem. Features  Smart Micropro …

Comments, Questions and Opinions: