Manualios.com

GAI-Tronics Titan Installation And User Manual

GAI-Tronics Titan Manual Online:

3.15, 512 votes
GAI-Tronics Titan User Manual
GAI-Tronics Titan User Guide
GAI-Tronics Titan Online Manual

Text of GAI-Tronics Titan User Guide:

  • GAI-Tronics Titan, 7 VoIP Telephone. The easiest way to get started is to make a network connection to the unit and log on via a web browser. The unit is initially set with a static IP address: IP address 192.168.1.2 It will request a user name and password, the initial factory settings are: User Name user Password password The phone’s home page is as shown below, and allows access to all the other configuration pages. Use the Network IP Settings page to change IP settings appropriate for the intended network. Full help is available from www.gai-tronics.co

  • GAI-Tronics Titan, VoIP Telephone. 12 3. Drill holes in the wall at the marked positions. Select appropriate screws, wall plugs etc., for the type of wall, bearing in mind that the weight of the complete phone is around 1.5kg. 4. Route the cable to within the recess, and make connections to the telephone as shown in section 6.5. 5. Secure the telephone to the wall taking care not to trap any wires. Note that the gasket on the rear of the faceplate is intended to make a weather seal when compressed against a smooth surface. Do not rely on this gasket to k

  • GAI-Tronics Titan, 13 VoIP Telephone. Do not use the Rear Casing as a template to drill the holes. Work only from the marked positions. 2. Drill the holes in the vertical surface to suit the best method of fixing. 3. Ensure the Rear Casing is securely attached to the vertical surface using the four 7mm diameter screw holes provided. No sealing washers are necessary. IMPORTANT: Do not use countersunk headed fixing screws. Only use round head, socket cap head or pan head screws. Take care not to over tighten the screws, doing so may damage the case, could result in an unsafe condition and wil

  • VoIP Telephone. 14 7. Ensuring that the glands are at the bottom, pass a proprietary banding strap round each of the pole mounting clamps and the support pole. Tighten to a torque of 4.5Nm (3.3lb-ft) max. 8. Continue the installation by making the appropriate connections (section 6.5). 9. Reconnect the ringer. Secure the telephone Front Casing to the Rear Casin

  • GAI-Tronics Titan, VoIP Telephone. 22 Clamp cables by bending tabs 6.7. Commander Connections Make the appropriate connections as shown on the diagrams below. Take particular note of the cable clamping arrangements – all cables must be securely clamped in the clamps provided. Connection types and ratings: Output 1 - rating 10A at 250Vac, 10A at 30Vdc Output 2 - 5A at 250Vac, 1A at 24Vdc Refer to safety information in section 6.2 OP1 OP2 Clamp Clamp Network cable Connection to Output 1 Barrier Cabling example showing connection to Output 1 E- OP1 OP2 E+NC R+ LOOP R- NOCOM M+ M- WARNING! DO NOT DRILL ANY ADDITIONAL HOLES IN THIS CASE Ringer Serial port RJ45 connector Input connections Power connect

  • 23 VoIP Telephone. External power supply – 24-48Vdc, 200mA NOTE: Earlier models (produced prior to May 2008) are 48Vdc only. Check the connector legend as shown above. If it is marked "AUX" it can accept voltages between 24 and 48V DC. If it is marked "48V" it is 48V only. Control inputs - for connection to voltage free contacts on

  • GAI-Tronics Titan, VoIP Telephone. 32 GAI-TRONICS A division of Hubbell Ltd. Brunel Drive, Stretton Park Burton on Trent, DE13 0BZ England Tel: 01283 500500, Fax: 01283 500400 www.gai-tronics.co.uk The policy of GAI-Tronics is one of continuous improvement, therefore the Company reserves the right to change specifications without notice

  • GAI-Tronics Titan, VoIP Telephone. 20 Clamp cables by bending tabs Take particular note of the cable clamping arrangements – all cables must be securely clamped in the clamps provided. Refer to safety information in section 6.2 Connection types and ratings: Output 1 - rating 10A at 250Vac, 10A at 30Vdc Output 2 - 5A at 250Vac, 1A at 24Vdc External power supply - 24-48Vdc, 200mA (400mA for VR and Help Point units if powering from 24Vdc). NOTE: Earlier models (produced prior to May 2008) are 48Vdc only. Check the connector legend as shown above. If it is marked "AUX" it c

  • GAI-Tronics Titan, 5 VoIP Telephone. Vandal Resistant (VR) handsfree telephone: FRONTPLATE MICROPHONE SPEAKER LED FLUSH, 25mm CALL BUTTON Help Point handsfree telephone: FRONTPLATE MICROPHONE SPEAKER LED REAR ENCLOSURE PALM-OPERABLE, STAINLESS STEEL CALL BUTTONS

  • GAI-Tronics Titan, 21 VoIP Telephone. Control inputs - for connection to voltage free contacts only. Internal pull-up resistor source current = 300uA. These inputs form part of a SELV circuit and precautions must be taken to prevent hazardous voltages being applied to these circuits LAN connection - RJ45 on Cat5 or Cat5e UTP cable All other connections - 0.14mm² to 2.5mm² (26 to 14awg) for rigid/solid cables, 0.14mm² to 1.5mm² (26 to 16awg) for flexible/stranded cable. 6.6. Commander Installation 1. To prepare for installation, undo the three retaining screws shown to remove the front casing from

  • GAI-Tronics Titan, VoIP Telephone. 24 5. Test the operation of the telephone. Installation is now complete. 6.9. VR and Help Point Connections Make the appropriate connections as shown on the diagram below. Take particular note of the cable clamping arrangements – all cables must be securely clamped in the clamps provided. Connection details for VR and Help Points are identical to Titan, please refer to section 6.5 above. Note: if powering from 24Vdc, the power supply must be capable of delivering 400mA. 7. Aftercare

  • GAI-Tronics Titan, VoIP Telephone. 28 European Directives 73/23/EEC - Low Voltage Directive. 89/336/EEC - EMC directive 1999/5/EC – Radio Equipment & Telecommunications Terminal Equipment (R&TTE) Directive 2002/96/EC - Waste Electrical and Electronic Equipment (WEEE) Directive 2002/95/EC - Restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS) Recycling Information The symbol shown here and on the product means that the product is classed as Electrical or Electronic Equipment and should not be disposed with other household or commercial waste at the end of its working life.

  • GAI-Tronics Titan, VoIP Telephone. 30 10. Licensing Notices The firmware in GAI-Tronics VoIP products contains modules subject to licensing and copyright as follows: Module License u-boot GPL V2 Linux kernel GPL V2 Busybox GPL V2 Opal/PWLib Mozilla Public License V1.1 Modutils GPL V2 MTD GPL V2 NTP David L. Mills Copyright Notice These licence and copyright notices are available in full from our website at www.gai-tronics.co.uk/voipsupport.htm

  • 11 VoIP Telephone. 2. Ensuring that the glands are at the bottom, pass a proprietary banding strap round each of the pole mounting clamps and the support pole. Tighten to a torque of 4.5Nm (3.3lb-ft) max. 3. Continue the installation by making the appropriate connections (section 6.5) and re-fitting the face plate. 4. Re-tighten the straps firmly and trim of

  • GAI-Tronics Titan, VoIP Telephone. 26 Product features Configuration Embedded web server Embedded Telnet server Configuration file download Direct serial connection (9 way D type female connector) Command line interface SNTP with timezone and daylight saving Automatic updating via TFTP Password protection Monitoring and Reporting Real-time over TCP/IP Syslog application or email. Embedded SMTP client Automatic fault reporting Handset integrity monitoring Call Diversion Configurable call lists (max 20 entries)

  • GAI-Tronics Titan, 17 VoIP Telephone. 6. Connections and Installation 6.1. General IMPORTANT THIS PRODUCT CAN CONTAIN HAZARDOUS VOLTAGES. IT IS ESSENTIAL THAT THE WATERPROOF SEAL IS PROPERLY MADE DURING INSTALLATION, TO ENSURE THAT WATER CANNOT GET INTO THE ENCLOSURE. THE INGRESS OF WATER CAN CAUSE ACCESSIBLE PARTS OF THE TELEPHONE TO BECOME LIVE, AND THEREFORE MUST BE PREVENTED AT ALL COSTS. All possible measures must be taken to ensure water, fluid or dust does not contaminate the internal component

  • GAI-Tronics Titan, 3 VoIP Telephone. 1. Safety and Care Information ▲ IMPORTANT: THIS PRODUCT CAN CONTAIN HAZARDOUS VOLTAGES. IT IS ESSENTIAL THAT THE WATERPROOF SEAL IS PROPERLY MADE DURING INSTALLATION, TO ENSURE THAT WATER CANNOT GET INTO THE ENCLOSURE. THE INGRESS OF WATER CAN CAUSE ACCESSIBLE PARTS OF THE TELEPHONE TO BECOME LIVE, AND THEREFORE MUST BE PREVENTED AT ALL COSTS. ▲ Please read these instructions thoroughly before starting installation. These products must be installed by competent personnel familiar with electrical and network installations. ▲ Refer to safety information is se

  • GAI-Tronics Titan, VoIP Telephone. 10 4. Ensure that all four plastic flanged bushes are in place and the rear enclosure is screwed tightly to the surface to prevent any water ingress through the punched holes. 5. Complete the installation by making the appropriate connections (section 6.5) and re-fitting the face plate. 5.2.2 Pole mounting Kit No 100-02-0208-001 This accessory is for mounting GAI-Tronics telephones on to the side of round poles of 100mm to 200mm diameter (4 - 8in), or on to square or rectangular section uprights of 100mm to 150mm (4 – 6i

  • GAI-Tronics Titan, VoIP Telephone. 18 6.2. IMPORTANT SAFETY INFORMATION Please pay particular attention to the following points if hazardous voltages (>48V) are to be connected to either of the control outputs: The circuits that the relay contacts are connected to must be of the same type, i.e. Both mains, both SELV or both TNV. It is not permissible to mix the types of circuit connected to these relays. It is acceptable to connect mains circuits in the frequency range 45 to 65 Hz to these relays. For currents up to 5 Amps, the minimum conductor cross sec

  • GAI-Tronics Titan, 25 VoIP Telephone. 8. Technical Specifications Product features Power supply Power-over-Ethernet, 802.3af compliant (Class 0) via RJ45, or External power supply: 24-48Vdc, 200mA, except VR and Help Point models being powered from 24Vdc, which require 400mA. NOTE: Earlier models (produced prior to May 2008) are 48Vdc only. Check the connector legend as shown in section 6.5 or section 6.7. A separate, isolated supply must be provided for each telephone. Voltage range (24V versions): 22-50V Voltage range (48V versions):

  • GAI-Tronics Titan, 15 VoIP Telephone. 5.4. VR and Help Point From a mounting and installation point of view, VR and Help Point products are identical. 5.4.1 Wall/Pole Mounting When wall or pole mounted, VR and Help Point units must be fitted inside a dedicated rear enclosure. The rear enclosure is identical to the Titan enclosure (although usually without a door). Follow the Titan mounting information given in sections 5.2.1 (wall mounting) or 5.2.2 (pole mounting).

  • GAI-Tronics Titan, Doc. No. 502-20-0115-001 Iss 2. Jul 2008. (CN33078-001) Installation and User Guide Rugged VoIP Telephone Titan, Commander, VR and Help Point models GAI-TRONICS A division of Hubbell Ltd. Titan Commander Vandal Resistant Help Point

  • GAI-Tronics Titan, 19 VoIP Telephone. 6.4. Titan Installation 1. To prepare for installation, open the door (where fitted), then undo the four retaining screws to remove the faceplate from the rear enclosure. A 3mm Allen key is required. Caution – take care to support the spring-loaded door whilst open to prevent it slamming shut and trapping fingers. 2. The Titan telephone is intended for vertical installation to a wall or pole. Select the required mounting method (section 5) and mount the rear enclosure first where applicable. 3. Route t

More Instructions:

DOWNLOAD

Related Products and Documents (IP Phone):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Rocstor ROCPORT 9CX 320GB Operation & user’s manual rocstor/rocport-9cx-320gb-STZ.pdf 12 Nov 2023 48 3.64 Mb
2 GE JV247 Owner's manual and installation instructions ge/jv247-B97.pdf 30 Jan 2024 16 0.35 Mb
3 Init 08-1442 Assembly instructions init/08-1442-S9F.pdf 18 Oct 2023 1
4 Hotpoint EG21 Instruction and recipe book hotpoint/eg21-95H.pdf 20 Aug 2022 32 0.24 Mb
5 Frigidaire GLGC36S9ESA Use & care manual frigidaire/glgc36s9esa-L3U.pdf 16 Feb 2023 12
6 NETGEAR HDXB101-100NAS Features manual netgear/hdxb101-100nas-V58.pdf 15 Dec 2023 2

Similar Resources:

  • Cisco

    9971

    (2 pages)
    Cisco IP Phone 9971 Quick Reference Guide TO MAKE A CALL  Lift Handset or press the Speaker/Headset key  Dial number (press 0 for external calls) REDIAL LAST NUMBER  Press the REDIAL soft key CALL HOLD  From an existing conversation, press  Press to get the caller back from hold.  If there are multiple calls on hold, scroll …
  • Nortel

    6120

    (1 pages)
    Safety informationDo not rely on a cordless handset in emergencies.the vicinity of electrical detonators•Never use your handset in:shielded rooms•areas where radio transmission is forbidden•aircraft•water, moisture, or damp areas•Do not place your handset near:heat sources, direct sunlight, or unventilated areas•devices that generate strong magne …
  • Aastra

    6753i

    (2 pages)
    Basic Phone FeaturesMake a Call1. Lift the Handset, press a Line Appearance key or Handsfree key.2. Dial the number from the keypad. Answering a CallFor handsfree operation, press the Handsfree key or line/call appearance button for the incoming call.RedialPress the Redial key to call a recently dialed number.Ending CallsTo end a call replace the handset, or …
  • ASCOM

    d43

    (28 pages)
    1Ascom d43 and d63 DECT HandsetsSafety InstructionsSikkerhedsanvisningerSicherheitshinweiseInstrucciones de seguridadConsignes de sécuritéIstruzioni di sicurezzaVeiligheidsinstructiesSikkerhetsanvisningerInstruções de SegurançaTurvaohjeetSäkerhetsföreskrifter …
  • Cisco

    Cisco Headset 561

    (2 pages)
    Cisco Headset 561 and Cisco Headset 562 with Standard BaseFor Cisco IP Phone 8811, 8841, 8845, 8851, 8861, 8865, and 8865NR on Cisco Unied Communications ManagerQuick Reference GuideHeadset LED status indicationIncoming Call Blinking redActive Call Steady redHeadset paired with dock White LED blinking every 4 secondsHeadset and dock not paired White LED b …
  • Grandstream Networks

    GXP2130

    (1 pages)
    Grandstream GXP2130/GXP2140/GXP2160 IP Phone Quick User Guide Basic Phone Operation For detailed information please consult the GXP2130/GXP2140/GXP2160 User Manual available at: www.grandstream.com ©2014 Grandstream Networks, Inc. All rights reserved. Reproduction or transmittal of the entire or any part, in any form or by any means, electronic or …

Comments, Questions and Opinions: