Manualios.com

bon BXM-183L3G Operation & User’s Manual

bon BXM-183L3G Manual Online:

3.4, 745 votes
bon BXM-183L3G User Manual
bon BXM-183L3G User Guide
bon BXM-183L3G Online Manual

Text of bon BXM-183L3G User Guide:

  • bon BXM-183L3G, OSD Timecode Display On/Off Timecode Position Set the position of timecode. OSD Display Time Set menu display time (seconds) OSD Blend Set transparency of the menu. MENU Position Set menu position among Left Top, Right Top, Left Bottom, Right Bottom and Center. IMD/UMD Mode Display IMD/UMD. The screen aspect ratio will turn to 16:9 on this mode. IMD/UMD Name The text to display using IMD/UMD. Closed Caption Select one of 608 Line 21, 608 VANC, 608 Transcoded, 708 to display Closed 18

  • bon BXM-183L3G, AUDIO Audio Group Audio group can be assigned between 1 to 4. Play Channel L Select audio channel for left Play Channel R Select audio channel for right Level Meter Select Turns on/off audio level meters. Level Meter Size Select the size of the meters : Small or Large. Level Meter Position Select the position of the meters : Upper or Lower. Level Meter Direction Select Level Meter orientation among Horizontal or Vertical. Peak Decay Time Adjusts decay time of meters. 20

  • bon BXM-183L3G, MARKER Marker Ratio Select one of preset markers or user marker. To display marker, press Marker button in front of the monitor. Safety Area 16:9 Adjust size of the safety area when marker displayed on 16:9 screen. Safety Area 4:3 Adjust size of the safety area when marker displayed on 4:3 screen. Center Marker Set preference to display center marker or not. Marker Color Select marker’s color among White, Red, Green, Blue, Gray and Black. Marker Mat Set how to display outside of the safety area. Normal, Half(Gray), Black are selectable. Marker Thickness Set marker thickness between 1 to 10. 16

  • bon BXM-183L3G, External Remote Control Connecting GPI Port(RJ-45) Update Port (RJ-11) 1 2 3 4 5 6 Update (RJ-11) Update Terminal Assignment 1 PIN NC 4 PIN GND 2 PIN RX+ 5 PIN TX+ 3 PIN RX- 6 PIN TX- * Turn power off first and connect update cable when you update monitor firmware. Remote Control / GPI Port Pin Assignments 1 2 3 4 5 6 7 8 Remote (RJ-45) Remote PIN Assignment 1 PIN GPI Port 1 5 PIN GPI Port 5 2 PIN GPI Port 2 6 PIN GPI Port 6 3 PIN GPI Port 3 7 PIN GPI Port 7(FIXED) (TALLY OUT) 4 PIN GPI Port 4 8 PIN COMMON(GND) Each pin's functionality can be assigned on OSD System Menu, GPI Control section. 27

  • bon BXM-183L3G, DISPLAY3 Exposure Range Check (Video Range Check) Checks Y, C level and displays over-exposed or under-exposed area on screen. The base value can be Y, Cb, or Cr. Y Range Max / Min Set Y range value for range check. C Range Max / Min Set C range value for range check. Blink Color The filled area color by range check can be either Black, Blue, Green or Red. Blink Time Set blinking time of the area between 1 to 5 seconds. False Color Turn False Color mode on to check exposure levels of the picture. Focus Assist Menu Displays Focus Assist sub m

  • bon BXM-183L3G, Strange Color on BON Logo on Startup Reconnect the Power and Restart the Monitor. (Call for Service if the Symptom appeared more than 3 times) the Startup Logo Color was ok but Strange Color on Active Screen Make Monitor "Factory Default" and Try again. Select Test Pattern(Internal Pattern) in the menu and See if R,G,B Color is Correct. Check the Input Selection. Try with Different Cable. Check if Each Cable is correctly Connected when you use Component as Input. Screen Position Mismatch Make Monitor "Fa

  • bon BXM-183L3G, USB Firmware Update To update your monitor's firmware, request for a new firmware file to your local reseller or to BON Electronics. Move the file on a USB flash memory, insert it to your monitor. Please beware the file should be located in the root(top folder level), not in any folder. Also, the USB flash memory should have FAT32 or FAT file system. (General USB memory has FAT32 file system, usually) Set Update Firmware item as USB from SYSTEM menu. Some part of firmware cannot be updated by USB updating procedure, so please get help from your local dealer or expert before you update firmware with USB memory. Error Message when USB access or file not exist Message wh

  • Safety Instructions • To help avoid damaging your monitor, connect only one power (AC or DC) in operation. • Rough handling of product may cause physical damage or malfunction. • Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock. • To avoid electric shock, never touch the inside of the monitor. Only a qualified

  • bon BXM-183L3G, 3G Level B Audio Select one Audio source if 3G SDI is used, which has two audio sources. Speaker Source Select the speaker output among Auto / SDI / Line In. For HDMI, use Auto mode. Speaker Volume Set volume of speaker. Be noted that Line Out level won't be affected. 21

  • bon BXM-183L3G, Assignable functions are listed below. Function Name Description SDI-1 Input Switches the input to SDI-1 SDI-2 Input Switches the input to SDI-2 HDMI Input Switches the input to HDMI YPbPr Input Switches the input to YPbPr CVBS-1 Input Switches the input to CVBS-1 CVBS-2 Input Switches the input to CVBS-2 CVBS-3 Input Switches the input to CVBS-3 KEY-UP ▲ CURSOR UP on Menu Control. KEY-DOWN ▼ CURSOR DOWN on Menu Control. KEY- MENU Menu On/Off KEY-ENTER Enter Button Aspect Aspect On/Off 1:1 Scan On/Off 1:1 SCAN Function On/Off H/V Delay On/Off H/V Delay Function On/Off TC Display On/Off TC Display On/Off ALM Display

  • bon BXM-183L3G, COLOR Color Temperature Select color temperature among 3200K, 5400K, 6500K, 9300K or USER. (Gain and Offset menu are displayed on USER temperature only) Red/Green/Blue Gain (USER mode only) R,G,B gains are adjustable on User mode. Red/Green/Blue Bias (USER mode only) R,G,B bias are adjustable on User mode. 14

  • WF Intensity Adjust color saturation of the waveform between 0 to 63. WF & Vector Size Select size of Waveform or Vector Scope. WF & Vector Blend Adjust transparency of the scope. P&P Combination Table 11

  • bon BXM-183L3G, Corporate Headquarters Tresebelle-Sky 2F, 1479 Gayang-2, Gangseo-gu, Seoul, South Korea Research / Service Center Vision Tower 7F, 1481 Gayang-2, Gangseo-gu, Seoul, South Korea Telephone +82 2 2659 0333 FAX +82 2 2659 8133 Web http://www.bon.co.kr Email [email protected] 38

  • Captions. In special condition such as menu display status, captions are not displayed. The list of its sub menus are below. V-Chip SD-SDI, Composite signal might contain V-Chip data. Turn this mode on to display V-Chip information on screen. CC708 Service Select one of CC service as your preference. Service 1: general captions. Service 2: translated captions. Service 3,4: not assig

  • bon BXM-183L3G, Contents Safety Instructions.......................................................................................................................3 Front............................................................................................................................................4 Rear.............................................................................................................................................6 MENU Description..................................................................................................................

  • bon BXM-183L3G, Focus Assist Display Turns on Focus Assist mode. This mode can be set also by pressing Focus Assist button in front. Focus Assist Level The sensitivity of the focus assist function can be set between 0 to 48. Focus Assist Color Set brush color of focus assist mode among Blue, Green, and Red. 13

  • bon BXM-183L3G, GPI GPI Control Turns on/off external monitor control function. GPI Port 1,2,3,4,5,6 Assigns each GPI port’s function. (e.g. SDI 1 input, HDMI input, Tally Red) See EXTERNAL REMOTE CONTROLLING section for details. Remote ID Number Assigns the ID for the monitor to control through serial port. 0 to 99 can be assigned. Serial Remote Turns serial remote function on. All front buttons are locked on this mode. To exit from this mode, press and hold Menu button for 3 seconds. Network Connection To connect to a ne

  • bon BXM-183L3G, F/W Update Turns update mode on. Select Serial or USB port for update. After firmware update, the monitor should be turned off/turned on, and Factory Default should be loaded before use. Firmware Version This version number is required when you request for service. Operating Time This indicates total hours that the monitor operated. 25

  • bon BXM-183L3G, Troubleshooting Try these if you have trouble in using the monitor. Call for Service if you can't solve the problem even after you tried these solutions. Symptom Solution Power isn't turned on Check Connectivity of Power Cable between Outlet and the Monitor. Press and Hold Power button for more than one second. Try with Other Monitor or Electric Device using the same Power Cable. Screen is Black and All Button Lights are On in startup process Reconnect the Power and Restart the Monitor. (Call for Servi

  • bon BXM-183L3G, Rear 1) AC Power 2) SDI Input 3) SDI Loop-Through Out 4) Component YPbPr/RGB or CVBS 1,2,3 Port 5) Component YPbPr/RGB or CVBS 1,2,3 Port Loop-Through Out 6) External Sync 7) External Sync Loop-Through Out 8) DVI 9) HDMI Port 10) Ethernet Port External control via PC is able with this port by using 'Wall Control Program'. 6

Related Products and Documents (Monitor):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 FULGOR milano 700 series Use & care manual fulgor/milano-700-series-718.pdf 28 Sep 2023 128
2 Dunham-Bush R22 WCPS-B Series Installation operation & maintenance dunham-bush/r22-wcps-b-series-Q9V.pdf 26 Oct 2022 30
3 Naxa NAS-3048 Instruction manual naxa/nas-3048-692.pdf 17 Sep 2023 14
4 Briggs & Stratton 400000 Operating & maintenance instructions briggs-stratton/400000-8U5.pdf 24 Jul 2023 20 3.26 Mb
5 Arrow Storage Products VM1012-C1 Owner's manual & assembly instructions arrow-storage-products/vm1012-c1-H73.pdf 12 Oct 2023 35 1.39 Mb
6 JUKI DLU-5490N Specifications juki/dlu-5490n-Y22.pdf 10 Mar 2024 4

Similar Resources:

  • Abex Exhibits

    LUMIWALL LW-36

    (3 pages)
    SPECIFICATIONS 3ft x 6ftAssembled unit:36”w x 72”h x 17.5”d50 lbs / 22.7 kgSGraphic area:35 13/16”w x 71 13/16”hLUMIWALL LED Backlit fabric displayLUMIWALL is constructed of aluminum extrusion and features SEG press fit fabric graphicsfor hassle free set up. Heavy duty aluminum feet ensure maximum stability. Graphics areprinted on premium fabric d …
  • YORKVILLE

    YX12

    (1 pages)
    ➲ 200 Watts➲ 12-inch Woofer➲ 1-inch Neodymium Compression Driver➲ 1.4-inch Aluminum Diaphragm Horn Driver (1-inch Exit)➲ Designed as Front-of-house or Monitor Loudspeaker➲ Innovative Dual-bulb CTL™ High Frequency Protection➲ 90° x 40° Custom ABS Waveguide Horn➲ Solid Plywood Cabinet Construction➲ Speakon™ & 1/4-inch Inputs➲ Al …
  • Digimerge

    DH100 Series

    (140 pages)
    www.digimerge.comCopyright © 2012 Digimerge Technologies Inc.Instruction ManualEnglish Version 4.0DH100 SeriesDigital Video Surveillance Recorder4/8/16 H.264 CMS-DH 3G Mobile Real-Time View & Record …
  • Philips

    230WP7NS

    (2 pages)
    For preview purpose onlyBoost your professionalproductivityA professional LCD display designed for business: The big, widescreen Philips 230WP7 gets the job done better with triple input options and super-wide viewing angle while an ergonomic base and USB solution add comfort and convenience.Designed for maximum productivity• Big, widescreen ideal for view …
  • Samsung

    SyncMaster 3 series

    (43 pages)
    LED TV MONITORuser manualThank you for purchasing this Samsung product. To receive more complete service, please register your product atwww.samsung.com/register(MFM TV)TB300TB350TB530 …
  • Daewoo

    DP-HG22

    (13 pages)
    HWAANLGLE RUNITPLASMA MONITOR (DISPLAY) WALL HANGER UNITINSTRUCTION MANUALDP-HG22Thank you for purchasing the Daewoo Electronic Plasma Display Wall Hanger Unit. Thiswall unit is specifically designed for use with the Daewoo Plasma Display. To ensure thesafe operation of the unit, please read these instructions before installing. …

Comments, Questions and Opinions: