Variquest Trifecta 800 Operation & User’s Manual

Text of Variquest Trifecta 800 User Guide:

• Variquest Trifecta 800, PAGE 40 Hotend Replacement Insert the heater cartridge back into the right side of the heater block. Orientate the heater cartridge wires so they point toward the back of the extruder. 9 Use the 1.75mm hex key to tighten the setscrew that secure the heater cartridge in place. 10

• Variquest Trifecta 800, PAGE 41 Hotend Replacement Carefully thread the cooling fan panel in between the heater cartridge and thermistor wire. 11 Once the components are in place, the thermistor wires should go around the back of the hotend heater block, and both wires from the cartridge and thermis- tor will come under and out from the cooling fan mount. 12

• Variquest Trifecta 800, If you are having trouble feeding the lament into the hotend, pull the lament out and trim the tip of the lament with a pair of scissors. Extend the lament guide tube from the retracted position. 1 Remove the lament spool from the packaging and place it on the spool holder. 2 Take the end of the lament from the spool and insert it into the guide tube. 3 5 PAGE 9 Filament Installation 4 Thread the lament through the guide tube and insert it into the extruder. You’ll need to push down on the tens

• Variquest Trifecta 800, PAGE 29 Troubleshooting Printer Issues Prints do not stick to the bed despite using the bed-leveling wizard. The bed-leveling wizard will serve as a good reference point to which to level your bed. Depending on the accuracy of the calibra- tion, you may need to make micro adjustments once the printer begins a print. As the printer begins a print and extrudes the outer skirt of the model, check to see if the skirt is sticking rmly onto the blue tape. If the lament seems bead-like, adjust the thumbscrew closest to the affected area cclockwise to bring the distance of the print surface closer to th

• Variquest Trifecta 800, PAGE 30 Troubleshooting Software Issues Printer driver not recognized when connected to the computer. Install the Trifecta™ slicing software to obtain the required drivers for the printer connection. To install the drivers manually, navigate the Trifecta™ slicing software directory: C:/Program Files/VariQuest/Trifecta Software/drivers/ Run dpinst32 or dpinst64 depending on if the computer is running a 32bit or 64bit OS. Imported a model into the Trifecta™ slicing software but cannot slice and export. Scale any oversized model within the Trifecta™ slicing software down to not exceed the build volume. Oversized models will be shaded in grey.

• Variquest Trifecta 800, PAGE 37 Hotend Replacement Move the right print bed cooling fan to give enough clearance to the hotend. Pull down on the hotend and retract the unit out of the seating. 3 With the hotend still attached to the thermistor and heater cartridge wire, swing the hotend around the backside of the cooling fan panel to expose the wires. 4

• Variquest Trifecta 800, PAGE 18 Model Rotation Sometimes when you import a model it may not be facing the right way, with the rotate tool, you can adjust the rotational angle on each individual axis. In the rst image, you can see that the vase is lying on its side. Since we want to print it with the at base as the bottom, we'll use the Rotate Tool to correct this.

• Variquest Trifecta 800, Table of Contents SAFETY WARNINGS 3 WARRANTY 4 SPECIFICATIONS 5 PRINTER OVERVIEW 6 UNBOXING 7 FILAMENT INSTALLATION 9 PRINT BED INSTALLATION 10 PRINT BED CALIBRATION AND STARTING A PRINT 11 TRIFECTA™ SOFTWARE INSTALLATION 13 BED LEVELING GUIDE 12 IMPORTING AND PRINTING A MODEL 14 SLICING SETTINGS 15 EXPORTING A FILE 17 MODEL ROTATION 18 MODEL SCALING 20 MEASURING FILAMENT DIAMETER 25 UPDATING PRINTER FIRMWARE 26 TROUBLESHOOTING 28 PRINTER CARE MAINTENANCE 31 HOTEND REPLACEMENT 35 GLOSSARY 44 SLICING SETTINGS EXPLAINED 22

• Variquest Trifecta 800, PAGE 42 Hotend Replacement Insert the hotend mount back into the carriage. 13 Insert both hotend mount screws in. You will need to push from the bottom of the hotend mount to align the mounting holes. 14

• Variquest Trifecta 800, PAGE 20 Model Scaling When importing in an oversized model that exceeds the printer’s print volume, the model will be shaded in gray. We can utilize the Scale Tool to adjust model sizes bigger or smaller. To scale uniformly, click on the scaling node (grey) and drag your mouse left or right until the model is at your desired size.

• PAGE 31 Printer Care and Maintenance Filament Care WHEN NOT IN USE: Retract the lament and coil back onto the spool. Thread the loose end through any of the holes to prevent the lament from tangling. INSTALLING THE SPOOL: Rest the spool on the spool holder on the back of the printer. Make sure the spool will spin clockwise as the lament feeds into the guide tube.

• Variquest Trifecta 800, PAGE 19 Model Rotation Once the Rotate tool is activated, three rotational rings will envelope the 3D model, each individual ring will allow you to control one of the three rotational axis (X,Y,Z). In this example, we rotated the Y-axis ring to bring the model upright. To rotate, click on the axis you wish to wish to rotate on, hold down your left mouse button and drag until you are satised with the angle. You can also hold down your Shift key to rotate in 90 degree increments. You can always click on the Reset button to reset the orientation back to the model’s imported state.

• Variquest Trifecta 800, PAGE 3 There is a risk of shock. Contact a certied technician to service your Trifecta™ 800 printer. In case of emergency disconnect the power cable from the socket. SHOCK The Trifecta™ 800 3D printer prints with molten plastic which emits a slight odor during operation. Setup the Trifecta™ 800 in a well-ventilated environment. VENTILATION The Trifecta™ 800 contains multiple moving parts that can cause injuries. Do not reach inside the Trifecta™ 800 during operation. MOVING PARTS The Trifecta™ 800 hotend heats up to high temperatures during operation. Allow the hotend to properly cool down before reaching in your hand. HOT SURFA

• Variquest Trifecta 800, PAGE 39 Hotend Replacement Remove the thermistor from the heater block by unscrewing the bronze setscrew by hand. 7 Take the new hotend unit and screw the thermistor back into the heater block by hand. Avoid screwing in the thermistor setscrew with tools to prevent causing damage to the thermistor bulb. 8

• Variquest Trifecta 800, PAGE 27 Updating Printer Firmware 5. Allow the rmware to upload to the printer. Do not disconnect the cable at this time. 6. All done! Click Ok to close the window and you can now disconnect the USB cable from the printer and computer.

• Variquest Trifecta 800, PAGE 32 Printer Care and Maintenance Gantry Linear Bearing + Rod Lubrication BEFORE YOU BEGIN: Only use machining oil on the X+Y axis smooth rods and linear bearings. Grease based lubricant can seize and damage linear bearings. Apply a single drop on each of the smooth rods and manually move the carriage around so the machining oil can seep into the linear bearings and bushings.

• PAGE 16 Slicing Settings RESOLUTION INFILL TEMP PROFILE TR FILAMENT WALL SPEED SUPPORT ANGLE Ext On All Medium: 200 micron VariQuest™ Trifecta™ 10% 1.73 1 70mm/s 220 HotendC Off Off 50 BRIM A - Change resolution settings. Choose from 300, 200, 100, and 50 micron. Default set to Medium - 200. B - Change Inll percentage. Adjust object density, default set to

• Variquest Trifecta 800, From the main menu, turn the dial to scroll to Wizard. Push down on the dial to select. 1 Select the Bed Level option and follow the on-screen instructions to level the print bed. 2 From the main menu, turn the dial to scroll to Print. Push down on the dial to select. 1 Scroll down to the le you want to print and push down again to start the print. 2 MAIN TEST_PRINT.G VASE.G BRACELET.G YOUR_PRINT.G WIZARD Exit Bed Level New Filament TempPrint MAIN MENU Status Control Wizard TempPrint MAIN MENU Statu

More Instructions:

	Variquest Trifecta 800 Quick start quide 17-11-2023 2	DOWNLOAD
	Variquest Trifecta 800 Troubleshooting tips 30-12-2023 4	DOWNLOAD
	Variquest Trifecta 800 Quick start manual 23-09-2022 4	DOWNLOAD

Related Products and Documents (3D Printers):

Comparable Devices:

Similar Resources:

• Sindoh A1 Series (133 pages) A1 Series User Manual Read the User manual before operating the product, and keep the manual at a convenient place near the product. 3dprinter.sindoh.com …

• XYZ Printing da Vinci 1.0 Pro (22 pages) da Vinci 1.0 ProUser ManualENGProduct Safety Product Description Printer screen menu, functions and messagesFunctional operations and descriptions Print Support Details Product Model: da Vinci 1.0 Profe …

• Creality AL-BMG (25 pages) AL-BMG Air Cooled Extruder Assembly Manual 1. Thank you for purchasing our products! Please check all the parts form the package for intactness. If there is any missing or damage parts please contact the seller immediately. Before installation please check if all the fans heaters are in correct voltage. 2. Disassemble the stock print head，remove all the …

• Flashforge DREAMER (8 pages) This guide only applies to Dreamer 3D printer of FlashforgeQuick Start GuideCaution1. Do not peel the yellow film from the build plate. It is heat-resistant tape, which makes objects stick to the build plate easily.2. Do not remove the wrapping around the nozzle. It consists of ceramic fiber and heat-resistant tape that help to keep the nozzle at a const …

• MUTOH VJ-628 ValueJet (90 pages) Operation ManualOperations and Maintenance MethodsVJ-628/628X• Unauthorized copying or duplication of the whole or part of the contents of this manual is prohibited.• Every care has been taken in writing the contents of this manual, but please contact MUTOH or the dealer you purchased the product from if you find any unclear, erroneous or otherwise unsat …

• Grizzly G0923 (56 pages) COPYRIGHT © MAY, 2020 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.#AI20901 PRINTED IN CHINAV1.05.20MODEL G09233D PRINTEROWNER'S MANUAL(For models manufactured since 05/20) …

Comments, Questions and Opinions: