Manualios.com

Whirlpool WHES48 Installation & Operation Manual

Whirlpool WHES48 Manual Online:

4.65, 1536 votes
Whirlpool WHES48 User Manual
Whirlpool WHES48 User Guide
Whirlpool WHES48 Online Manual

Text of Whirlpool WHES48 User Guide:

  • Whirlpool WHES48, 7 Installation RequirementsInstallation Requirements VALVE DRAIN REQUIREMENTS Using the flexible drain hose (included), measure and cut to the length needed. Flexible drain hose is not allowed in all localities (check your plumbing codes). If local codes do not allow use of a flexible drain hose, a rigid valve drain run must be used. Purchase a com- pression fitting (1/4 NPT x 1/2 in. minimum tube) and 1/2" tubing from your local hardware store. Plumb a rigid drain as needed (See Figure 6). NOTE: Avoid drain hose runs longer than 30 feet. Avoid elevating the hose more than 8 feet above the floor. Make the valve drai

  • 3 Specifications & Dimensions Questions? Call Toll Free 1-866-986-3223 Monday- Friday, 8 AM - 7 PM EST or visit www.ecodynewatertreatment.com When you call, please be prepared to provide the model, date code and serial number, found on the rating decal, typically located on the rim below the salt lid hinges. *Capacity to reduce clear water iron is substantiated by WQA test dat

  • Whirlpool WHES48, 17 Programming Your E-Z Touch Water Softener SET IRON LEVEL The softener’s electronic control can adjust cycle times to compensate for ferrous (clear water) iron in the water. When the softener’s electronic control is first powered up, the iron level is set at 0. NOTE: The iron level will always be displayed in ppm (parts per million), regardless of whether the Hardness units setting is grains or ppm. The conversion factor is 3 grains per ppm of clear water iron. To enter your water’s iron level: 1. Press the SETUP button on the softener status screen (See Figure 45). 2. Press the RIGHT ( ) button three times to display the screen shown in Figure 48. FIG. 48 FIG. 49 3. Press the SE

  • Whirlpool WHES48, 4 Water Softener Safety Your safety and the safety of others are very important. We have provided many safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING” These words mean: You can be killed or seriously injured if you don’t immediately follow instructions. You can be killed or seriously injured if you don’t follow instructions. All safety messages will tell you what the

  • Whirlpool WHES48, 25 Troubleshooting MANUAL ADVANCE REGENERATION CHECK This check verifies proper operation of the valve motor, brine tank fill, brine draw, regeneration flow rates, and other controller functions. Always make the initial checks first. Use the following procedure to advance the water softener through the regeneration cycles to check operation. In the following steps you will use the ADVANCE VALVE button to move the valve into each cycle and check correct switch operation (See Figures 87 & 88). NOTE: The follow

  • 10 FIG. 13 Ground Clamp Electrical Shock Hazard Install metal ground clamp to metal house water supply pipe before beginning installation. Securely tighten connection in center of metal ground clamp. Failure to do so can result in death or electrical shock. COMPLETE INLET AND OUTLET PLUMBING Measure, cut, and loosely assemble pipe and fittings from the main water pip

  • Whirlpool WHES48, 21 Customizing Features / Options SET UNITS The softener can be set to display values such as vol- ume and water hardness in either English or Metric units. In addition the clock may be set to display time in either 12-hour (AM/PM) or 24-hour format. VOLUME UNITS To select between gallons and liters as volume units: 1. Press the SETUP button on the softener status screen. 2. Press the LEFT ( ) button twice to display the screen shown in Figure 69. FIG. 71 FIG. 72 FIG. 69 3. Press the ADVANCED SETUP button. The display will change to the following screen. 4. Press the RIGHT ( ) button twice to display the screen shown in Figure 71. FIG. 70 6. Press the button next to the desired volu

  • Whirlpool WHES48, 23 FIG. 79 Broom Handle Pencil Mark 1” - 2” Salt Salt Bridge Water Level Push Tool into Salt Bridge to Break FIG. 80 Cap O-ring Seal Screen Support Screen Gasket *Flow Plug (HVDC) Housing Ferrule Nut Cone Screen *Flow Plug *Install with lettered side up, concave side down. CLEANING THE NOZZLE & VENTURI A clean nozzle & venturi (See Figure 80) is a necessity for the water softener to work properly. This small component creates the suction to move brine from the brine tank, into the resin tank. If it should become plugged with sand, silt, dirt, etc., the water softener will not work, and hard water will result. Nozzl

  • Whirlpool WHES48, 12 Water Softener Setup TOUCH SCREEN Controls for programming the water softener are dis- played on a touch screen, located on the softener’s front panel (See Figure 17). On-screen “buttons” appear as rectangular outlines with rounded corners and change with each display (See Figures below). Button presses are acknowledged with a “beep.” NOTE: Before cleaning the touch screen to remove fingerprints, unplug the transformer. The con- troller’s memory items (including clock time, water hardness, etc.) are retained during brief power interruptions. Use a microfiber towel or household cleaner safe for plastics

  • Whirlpool WHES48, 16 Programming Your E-Z Touch Water Softener SETUP BUTTON The SETUP button on the softener status screen is used to set items of basic operating information: =Set current time =Set water’s hardness =Set recharge time =Set water’s iron level =Advanced setup (Accesses more items that can be set. These are described starting on Page 19) =Set language FIG. 43 SET TIME When the softener’s electronic control is first powered up, the setup procedure prompts you to set the cur- rent time (See Page 12). To change the time at a later date, such as after a long power loss:

  • Whirlpool WHES48, 8 Installation Instructions TYPICAL INSTALLATION Inlet Outlet Clips Ground Clamp To Outside Faucets Single Bypass Valve Ground Clamp Conditioned Water Hard Water Main Water Pipe Plug-in Transformer Water Softener Valve To Controller Valve Drain Elbow Valve Drain Hose* *Do not connect the water softener valve drain tubing to the salt storage tank overflow hose. Overflow Drain Elbow Salt Storage Tank Overflow Hose* Secure Valve Drain Hose in place over Floor Drain Ground Clamp Pipe 1” NPT Sweat Adaptor (not included) Clip Lubricated

  • Whirlpool WHES48, 20 Customizing Features / Options SET SALT EFFICIENCY When this feature is ON, the water softener will oper- ate at salt efficiencies of 4000 grains of hardness per pound of salt or higher (May recharge more often using smaller salt dosage and less water). The sof- tener is shipped with this feature set OFF, which uti- lizes the maximum rated capacity while most often achieving maximum salt efficiencies. When installing this unit in the State of California, you MUST turn this feature ON. To set this feature: 1. Press the SETUP button on the softener status screen. 2. Press the LEFT ( ) button twice to display the screen shown in Figure 63. FIG. 65 FIG. 66 FI

  • Whirlpool WHES48, 28 Valve Exploded View wear-strip seal cross-section view 100 101 102 103 104 105 106 107 108109110 111 112 113 114 115 140 116 117 118 119 120 121 122 123 124 126 125 127 128 129 130 131 132 133 134 135 136 137 138 139 141 142 143 144

  • Whirlpool WHES48, 14 Programming Your E-Z Touch Water Softener FIG. 23 SET LANGUAGE When the softener’s electronic control is first powered up, the setup procedure prompts you to set the lan- guage (See Page 12). To change the language: 1. Press the SETUP button on the softener status screen (See Figure 22). FIG. 22 2. Press the LEFT ( ) button to display the screen shown in Figure 23. FIG. 24 3. Press the LANGUAGE button and the display will change to show the Select Language screen (See Figure 24). 4. Press the button next to the desired language. When the desired language is checked, press the OK button. 5. To

  • Whirlpool WHES48, FIG. 82 E-Z Touch FIG. 85 FIG. 86 Troubleshooting 24 AUTOMATIC ELECTRONIC DIAGNOSTICS This water softener has a self-diagnostic function for the electrical system (except input power and/or water meter). The water softener monitors electronic com- ponents and circuits for correct operation. If a mal- function occurs, an error code appears in the display. A service person should be contacted to perform the diagnostics, see below, to further isolate the problem. Procedure for removing error code from dis- play: 1. Unplug transformer from electrical outlet. 2. Correct problem. 3. Plug in tra

  • Whirlpool WHES48, 27 Softener Parts List Key No. Part No. Description 1 7170296 O-Ring, 2-7/8” x 3-1/4” 2 7170254 O-Ring, 13/16” x 1-1/16” 3 7077870 Top Distributor 4 7170270 O-Ring, 2-3/4” x 3” 5 7105047 Repl. Bottom Distributor 6 7265025 Filter Screen 7 7176292 Clamp Section (2 req.) 8 7088033 Retainer Clip (2 req.) 9 7247996 Repl. Resin Tank, 10” x 40” 10 0502272 Resin, 1 cu. ft. 11 7221746 Brine Tube 12 7113016 Tubing Assembly 13 7131365 Screen 14 7142942 Clip 15 7308881 Brine Valve Body 16 7116713 Clip 17 0516924 Bottom Seal Retainer 18 0516211

  • Whirlpool WHES48, 6 PLUMBING CODES All plumbing must be completed in accordance with national, state and local plumbing codes. LAUNDRY TUBSTANDPIPE 1-1/2” air gap FLOOR DRAIN In the state of Massachusetts: The Commonwealth of Massachusetts plumbing code 248-CMR shall be adhered to. A licensed plumber shall be used for this installation. AIR GAP REQUIREMENTS A drain is needed for regeneration water (See Figure 3). A floor drain, close to the water softener, is preferred. A laundry tub, standpipe, etc. are other drain options. Secure valve drain hose in place. Leave an air gap of 1-1/2” between the end of the hos

  • Whirlpool WHES48, 19 Customizing Features / Options SET CLEAN FEATURE The Clean Feature with Sediment Guard technology is beneficial on water supplies containing ferrous (clear water) iron. The default setting is OFF. When set to ON, an additional backwash and fast rinse cycle will occur first, preceding the normal regenera- tion sequence. This provides extra cleaning of the resin bed before it is regenerated with the salt brine. To conserve water set this feature OFF if your water supply does not contain iron or sediments. To set this feature: 1. Press the SETUP button on the softener stat

  • 26 8 7 6 5 Softener Exploded View 1 2 3 4 5 6 7 9 10 Valve Assembly See Pages 28 - 29 for parts 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 30 31 32 33 34 35 36 37 38 39 40 41 122 8 42 43 29 Softener Exploded View 28

  • Whirlpool WHES48, How to install, operate and maintain your E-Z Touch Demand Controlled Water Softener Model WHES48 System tested and certified by NSF International against NSF/ANSI Standard 44 for hardness reduction and efficiency. System tested and certified by the Water Quality Association against CSA B483.1. Do not return water softener to store 7310359 (Rev K 9/9/11) Product No. W10270201 Manufactured and warranted by Ecodyne Water Systems 1890 Woodlane Drive Woodbury, MN 55125 Installation and Operation Manual Printed on recycled paper If you have any questions or concerns when installing, operating

  • Whirlpool WHES48, 9 MOVE THE WATER SOFTENER INTO PLACE 1. Move the water softener into the desired location. Set it on a solid, level surface. IMPORTANT: Do not place shims directly under the salt storage tank to level the softener. The weight of the tank, when full of water and salt, may cause the tank to fracture at the shim. 2. Visually check and remove any debris from the water softener valve inlet and outlet ports. 3. Make sure the turbine assembly spins freely in the "out" port of the valve. 4. If not already done, put a light coating of silicone gre

  • 13 Programming Your E-Z Touch Water Softener SOFTENER STATUS SCREEN During normal operation, the softener’s display shows a screen like the one in Figure 20, below. The dis- play automatically returns to this screen from other screens after 4 minutes of inactivity. FIG. 20 Indicates water flow through the softener Indicates salt level in the salt storage tank TANK LIGH

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Witura WT-1010SA Operation & user’s manual witura/wt-1010sa-98O.pdf 11 Aug 2023 42 2.11 Mb
2 Makita 2704 Instruction manual makita/2704-2WE.pdf 26 Feb 2023 24
3 RCA J22C760 Operation & user’s manual rca/j22c760-84A.pdf 15 May 2023 96 5.28 Mb
4 Samsung SP-R6100 Operation & user’s manual samsung/sp-r6100-999.pdf 17 Nov 2022 67 0.39 Mb
5 Sharp 19J-M100 Service manual sharp/19j-m100-74C.pdf 04 Jul 2022 29 3.08 Mb
6 Philips AX7101 Specifications philips/ax7101-445.pdf 09 Oct 2022 2 2.87 Mb

Similar Resources:

  • Reliable

    DDX PrePaK

    (26 pages)
    Model DDX PrePaK, Type DPreaction System4”(100mm) & 6”(150mm)Instructions forInstallation, Operation,Care and Maintenance10 psi (0,7 bar) Pneumatic Supervising PressureSingle InterlockDouble InterlockThe Reliable Automatic Sprinkler Co., Inc. 103 Fairview Park Drive , Elmsford, New York 10523Bulletin 733 Rev. BBulletin 733 Rev.B …
  • Zazen

    Alkaline Water

    (8 pages)
    www.zazen.com.auzazen Alkaline Water 1300 78 24 25 All you need to know to setup and lookafter your zazen Alkaline Water systemDid you know?Every system purchased contributes towards the Water Ambassador School Program - funded by zazen Water.Your zazen Water system is totally BPA free.Drinking zazen Water costs only 5c …
  • Infiltrator

    Presby Advanced Enviro-Septic

    (24 pages)
    © Presby Environmental, Inc., Missouri Design & Installation Manual, September 2020 Edition Design and Installation Manual for Advanced Enviro-Septic® (AES) Wastewater Systems Missouri Table of Contents 1.0 INTRODUCTION 3 1.1 State-Specific Information 3 1.2 Background 4 1.3 System Components 5 2.0 SYSTEM DESIGN 6 2.1 …
  • AmeriWater

    CHIE VARIABLE SPEED BOOSTER PUMP SYSTEM

    (14 pages)
    P/N 98-0118 Rev.B 28OCT10 CHIE VARIABLE SPEED BOOSTER PUMP SYSTEM OPERATION & MAINTENANCE MANUALManufactured With Pride In The USAwww.ameriwater.com • 800-535-5585 AmeriWater • 3345 Stop 8 Rd. • Dayton, OH 45414 …
  • Kenmore

    625.3486

    (32 pages)
    OWNER'SMANUALMODEL NO.625.348600Caution:Read and FollowAll Safety Rules andOperating InstructionsBefore First Use ofThis Product.If you have questions wheninstalling, operating or main-taining your softener, andwhen setting the timer, callthis toll-free number...1-800-426-9345SAVE THIS MANUALHigh Flow Deluxe DemandWater Softener• Warranty• Start Up …
  • Aqua-Base

    ESB Series

    (50 pages)
    J:\Etude-3d\Aquaset\0-DOSSIER TECHNIQUES\1-sw-plaisance\ESW\00-ESW 0707\09- Manuels Utilisateur\DOC UTILISATEUR ESB FRUKES 2009-10-B.doc VERSION 2009-10-B FR/UK/ES Page 1/1 P3 MANUEL UTILISATEUR p17 OWNER MANUAL p31 MANUAL DE UTILIZACIÓN ATTENTION : Lisez attentivement l’intégralité de cet …

Comments, Questions and Opinions: