United Technologies MobileView 9000 Series Operation & User’s Manual
|
United Technologies MobileView 9000 Series, Figure 17: DDNS Settings 2. Check the Enable DDNS checkbox to enable this feature. 3. Select DDNS Type. Three DDNS types are selectable: DynDNS, IPServer and No-IP. When selecting DynDNS follow these steps: • Enter Server Address of DynDNS (e.g. members.dyndns.org). • In the Domain text field, enter the domain name obtained from the DynDNS website. • Enter the Port of DynDNS server. • Enter the User Name and Password registered on the DynDNS website. • Click Save to save the settings. Figure 18: DynDNS Settings MobileView 9000 & 9100 Series Analog/IP Camera User Manual 19
United Technologies MobileView 9000 Series, Figure 52: Device Information Maintenance Rebooting the Camera 1. Enter the Maintenance interface: Configuration> Basic Configuration> System > Maintenance Or Configuration > Advanced Configuration> System > Maintenance: 2. Click Reboot to reboot the camera. Figure 53: Reboot the Device Restoring Default Settings 1. Enter the Maintenance interface: Configuration> Basic Configuration> System > Maintenance Or Configuration > Advanced Configuration> System > Mai
United Technologies MobileView 9000 Series, Modify an IP Address • Left-click an IP address from filter list and click . • Modify the IP address in the text filed. Figure 51: Modify an IP • Click the button to finish modification. Delete an IP Address • Left-click an IP address from filter list and click . Delete all IP Addresses • Click to delete all the IP addresses. 5. Click Save to save the settings. Viewing Device Information Enter the Device Information interface: Configuration> Basic Configuration> System > Device Information Or Configuration > Advanced Configuration> System > Device Information In th
United Technologies MobileView 9000 Series, 1. Enter the 802.1X Settings interface: Configuration > Advanced Configuration > Network> 802.1X Figure 22: 802.1X Settings 2. Check the Enable IEEE 802.1X checkbox to enable the feature. 3. Configure the 802.1X settings, including EAPOL version, user name and password. The EAPOL version must be identical with that of the router or the switch. 4. Enter the user name and password to access the server. 5. Click Save to finish the settings. 6. A reboot is required for the settings to take effect. Configuring QoS Settings QoS (Quality of Service) can help solve network delays and congestio
United Technologies MobileView 9000 Series, alarm events, the Primary stream is for normal recording, and the Alternate stream can be used for live viewing over cellular or for low-bandwidth archival. 3. You can customize the following parameters for the selected main stream or sub-stream: Video Type Select the stream type to video stream, or video & audio composite stream. The audio signal will be recorded only when the Video Type is Video & Audio. (Audio only available on MVC-9100) Resolution Select the resolution of the video output. Bitrate Type Select the bitrate type to constant or variable. Video Quality When bitrate type is sel
United Technologies MobileView 9000 Series, 2. Click Restore or Default to restore the default settings. Figure 54: Restore Default Settings Note: After restoring the default settings, the IP address is also restored to the default IP address, please be careful with this action. Exporting/ Importing Configuration File Enter the Maintenance interface: Configuration> Basic Configuration> System > Maintenance Or Configuration > Advanced Configuration> System > Maintenance 1. Click Export to save the configuration file of the current device. 2. Click Browse to se
United Technologies MobileView 9000 Series, Configuring Image Parameters Configuring Display Settings You can set the image quality of the camera, including brightness, contrast, saturation, hue, sharpness, etc. The Display parameters vary depending on the camera model. 1. Enter the Display Settings interface: Configuration> Basic Configuration> Image> Display Settings Or Configuration > Advanced Configuration> Image> Display Settings 2. Set the image parameters of the camera Figure 31: Display Settings Descriptions of parameter configuration Image Adjustment Brightness describ
United Technologies MobileView 9000 Series, Starting Live View In the live view window, click on the toolbar to start the live view of the camera. Figure 8: Live View Toolbar Table 3: Toolbar icon descriptions Icon Description / Start/Stop live view Manually capture the pictures displayed in live view and then save it as a JPEG file or BMP file. / Manually start/stop recording. Audio on and adjust volume /Mute. (Only available for MVC-9100) Note: Before using audio, please set the Stream Type to Video & Audio
United Technologies MobileView 9000 Series, 2. Configure the QoS settings, including video / audio DSCP, event / alarm DSCP, and Management DSCP. The valid value range of the DSCP is 0-63. The bigger the DSCP value, the higher the priority. SCP refers to the Differentiated Service Code Point; and the DSCP value is used in the IP header to indicate the priority of the data. 3. Click Save to save the settings. 4. A reboot is required for the settings to take effect. Configuring FTP Settings You can configure the FTP server information to enable the uploading of the captured pictures to the FTP server. The captured pictures can be triggered by events or a timing snapshot task. 1. Enter the FTP Se
United Technologies MobileView 9000 Series, event occurs. Send Email Send an email with alarm information to a user or users when an event occurs. To send the Email when an event occurs, you need to refer to Section 0 to set the related parameters. Upload to FTP Capture the image when an alarm is triggered and upload the picture to a FTP server. Note: Set the FTP address and the remote FTP server first. Configuring Video Tampering Alarm You can configure the camera to trigger the alarm when the lens is covered and take alarm response action. 1. Enter the Video Tampering Settings interface: Configuration> Advanced Configuration > Events > Video Tampering MobileView 9000 &
United Technologies MobileView 9000 Series, Detecting and Changing the IP Address You need the IP address of the camera to connect to the network camera using a computer. If you already know the IP address of the camera, skip to the next section, Accessing the Camera. The default IP address is 192.168.1.70, subnet is 255.255.255.0, and the port number is 8000. The default user name is admin, and password is 1234. 1. To get the IP address, you can install the Mobileview Camera Finder to list online devices. 2. To change the IP address and subnet mask as needed, inpu
United Technologies MobileView 9000 Series, Configuration > Basic Configuration > Network> Port Or Configuration > Advanced Configuration> Network > Port Figure 15: Port Settings 2. Set the HTTP port, RTSP port and HTTPS port of the camera. HTTP Port The default port number is 80. If you change it, it is recommended to use a port within the range 1024 to 65535. RTSP Port The default port number is 554. HTTPS Port The default port number is 443. If you change it, it is recommended to use a port within the range 1024 to 6
United Technologies MobileView 9000 Series, Saturation describes the colorfulness of the image color, which ranges from 1~100, and the default value is 50. Sharpness describes the edge contrast of the image, which ranges from 1~100, and the default value is 50. Exposure Settings Exposure Time: Value ranges from 1/3 to 1/100,000s. Adjust it according to the lighting condition. Gain: Select the value to adjust the image brightness. Iris Mode: Only Manual is selectable. Day/Night Switch Select the day/night switch mode, and configure the smart IR settings from this option. Day, night, auto, sche
SMTP Server The SMTP Server IP address or host name (e.g., smtp.263xmail.com). SMTP Port The SMTP port. The default TCP/IP port for SMTP is 25 (not secured). And the SSL SMTP port is 465. Enable SSL Check the checkbox to enable SSL if it is required by the SMTP server. Attached Image Check the checkbox of Attached Image if you want to send emails with att
United Technologies MobileView 9000 Series, Accessing the Camera Accessing by Web Browser 1. Open the web browser. 2. In the address field, input the IP address of the network camera, e.g., 192.168.1.70 and press the enter key to access the login interface. 3. Input the user name and password, and click Login. Note: The default user name is admin, and the password is 1234. Figure 3: Login Interface 4. When prompted, please follow the installation prompts to install the plug-in. MobileView 9000 & 9100 Series Analog/IP Camera User Manual 6
United Technologies MobileView 9000 Series, The below figure shows the white balance type selectable. You can choose it according to the real condition. For example, if in the surveillance scene, there is a fluorescent lamp, you can choose the white balance type as the Fluorescent Lamp. Figure 32: White Balance Image Enhancement Digital Noise Reduction: Off, Normal Mode and Expert Mode are selectable. Noise Reduction Level: For adjusting the noise reduction level and only valid when the DNR function is enabled. Video Adjustment Video St
Figure 21: SNMP Settings 2. Check the corresponding version checkbox ( , , ) to enable the feature. 3. Configure the SNMP settings. The settings of the SNMP software should be the same as the settings you configure here. 4. Click Save to save and finish the settings. 5. A reboot is required for the settings to take effect. Configuring 802.1X Settin
United Technologies MobileView 9000 Series, Configuring Time Settings You can follow the instructions in this section to configure the time synchronization and DST settings. 1. Enter the Time Settings interface: Configuration> Basic Configuration > System > Time Settings Or Configuration > Advanced Configuration > System > Time Settings Figure 10: Time Settings • Select the Time Zone. Select the Time Zone where the camera is located from the drop-down menu. • Synchronizing Time by NTP Server. Check the ch
Figure 44: Add a User Modify a User 1. Left-click to select the user from the list and click . 2. Modify the User Name, Level or Password. 3. In the Basic Permission field and Camera Configuration field, you can check or uncheck the permissions. 4. Click OK to finish the user modification. MobileView 9000 & 9100 Series Analog/IP Camera User Manual 45
United Technologies MobileView 9000 Series, Figure 11: Time Sync by NTP Server Note: If the camera is connected to a public network, you should use a NTP server that has a time synchronization function, such as the server at the National Time Center (IP Address: 210.72.145.44). If the camera is set in a customized network, NTP software can be used to establish a NTP server for time synchronization. • Synchronizing Time Synchronization Manually Enable the Manual Time Sync function and then click to set the system time from the pop-up calendar. Note: You can al
United Technologies MobileView 9000 Series, 2. Configure the following settings: Live View Parameters Protocol Type: TCP, UDP, MULTICAST and HTTP are selectable. TCP: Ensures complete delivery of streaming data and better video quality, yet the real-time transmission will be affected. UDP: Provides real-time audio and video streams. HTTP: Allows the same quality as of TCP without setting spe cific ports for streaming under some network environments. MULTICAST: It’s recommended to select MCAST type when using the Multicast function. For detailed information about
With this option, you can enable or disable the BNC analog output. Configuring OSD Settings You can customize the camera name and time on the screen. 1. Enter the OSD Settings interface: Configuration> Advanced Configuration > Image > OSD Settings Figure 33: OSD Settings 2. Check the corresponding checkbox to select the display of camera name, dat
Axis M1103 IP Camera Installation manual
M1103 |
Avigilon 8.0MP-HD-DOME-360 IP Camera Installation manual
8.0MP-HD-DOME-360 |
ZKaccess ZKIP472 IP Camera Operation & user’s manual
ZKIP472 |
3Jtech NetCAMit IP Camera Operation & user’s manual
NetCAMit |
Versiton BAR70 M855 IP Camera Operation & user’s manual
BAR70 M855 |
Axis M3014 IP Camera Operation & user’s manual
M3014 |
Axis P5522/-E PTZ IP Camera Operation & user’s manual
P5522/-E PTZ |
GeoVision GV-SD220 IP Camera Quick start manual
GV-SD220 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Sony | DSC-W730 | Specifications | sony/dsc-w730-883.pdf | 11 Sep 2023 | 3 | 0.22 Mb |
2 | JVC | KD-AVX77 - EXAD - DVD Player | Instructions manual | jvc/kd-avx77-exad-dvd-player-3X1.pdf | 09 Jul 2023 | 218 | |
3 | Casio | Algebra FX 1.0 PLUS | Manual | casio/algebra-fx-1-0-plus-641.pdf | 11 Aug 2023 | 32 | 0.19 Mb |
4 | Hubbell | ME | Operation & user’s manual | hubbell/me-838.pdf | 25 May 2023 | 24 | |
5 | ATEN | PE5220s | Operation & user’s manual | aten/pe5220s-8XW.pdf | 31 Jul 2023 | 90 | 2.95 Mb |
6 | GE | Appliances AEM24 | Owner's manual and installation instructions | ge/appliances-aem24-3JA.pdf | 11 Aug 2022 | 52 |
ALIBI
1www.observint.comALI-CD5021VSS_CQ 4/8/15Drop cableOSD joystickGimbal tilt pivot point set screw (2)RCA jack for setup monitor cableCable channelCamera back view (with dome removed)Power ConnectorHD-TVI video BNC ConnectorALI-CD5021VSS Camera drop cable connectorsWhat’s in the box • Camera assembly• Mounting screws with rubber seals (3) • …
ALI-CD5021VSS(4 pages) |
AVer
VC520 Pro Conference Camera Quick Installation Guide Package Contents Camera Unit Speakerphone Unit Remote Controller Power Adapter Power Cord* USB 3.0 Cable Camera Cable (10 m) Speakerphone Cable (10 m) 3.5 mm Audio Cable (0.9m) L-Mount Bracket Screws for Mount Drilling Paper Quick Guide Warranty Card AAA Batteries � …
VC520 Pro(10 pages) |
Ipcamdata
We keep improving the app, if the app interface is not accordance with the instructions, please go to IPcmera website: http://cd.ipcamdata.com for the latest instructions.Wire-Free Battery-Powered1080P Indoor & Outdoor Home Security CameraUser Manual801RTBEN Version Updated on 25 September 2018iSmartviewPro850G
…
iSmartViewPro(26 pages) |
Platinum CCTV
Platinum CCTV Surveillance Solutions CD-8361 Indoor/Outdoor Day/Night Long-Range IR Varifocal Camera with Sony 700 TVL CCD Installation Manual Outdoor Varifocal Hi-Res Day/Night Infrared CCD Armor Dome Camera with Sony EFFIO® DSP Http:// Platinum-CCTV.com
…
CD-8361(4 pages) |
HIKVISION
Hikvision Technical Manual ©2006 – 2011 by HIKVISION. All rights reserved. 1 DS-2CD762MF-FB(H) Network Camera Technical Manual
…
DS-2CD762MF-FB(H)(7 pages) |
Dahua
1Quick Installation Guide Attention: Please make sure the installation surface is thick enough to sustain at least 3X weight of the camera. Note: If you want to install in the wood surface, expansion bolts are not necessary. The screw depth shall reserve 8mm-10mm to sec …
HAC-HDW1220R(4 pages) |
Makita Blower BHX2501Blower PDF Instruction manual BHX2501, 19 |
Samson Monitor 6AOwner's manual for Samson 6A Monitor 6A, 64 |
LG LED TV 32LH51 seriesOwner's manual for LG 32LH51 series LED TV 32LH51 series, 24 |
Sony Headsets WH-CH500PDF Guide (@NF5223), Sony WH-CH500 Headsets (12.01.2024) WH-CH500, 2 |
Califone Portable Speakers PowerPro PA-916BPortable Speakers Datasheet (Califone PowerPro PA-916B) PowerPro PA-916B, 2 |
Panasonic TV TC-60PUT54Panasonic Product Guide: TC-60PUT54 PDF Operation & user’s manual - 755R69 TC-60PUT54, 193 |
Randall Amplifier RG1503HAmplifier #4YX8L5 RG1503H, 2 |
Blaupunkt Receiver Toronto RDM 126 USBlaupunkt Toronto RDM 126 US User Manual (Operating instructions manual), @PHTDKL Toronto RDM 126 US, 29 |
Ricoh Printer DDP 184PDF Manual (@128E1F), Ricoh DDP 184 Printer (Sun 10.2023) DDP 184, 4 |
Yamaha Speakers MS202PDF Manual (@G32K2C), Yamaha MS202 Speakers (Thursday 30-11-2023) MS202, 9 |
Frigidaire Cooktop FPEC3085KSAFPEC3085KSA (Cooktop ePDF Manual, #Y786ND) FPEC3085KSA, 14 |
Chicago Electric Inverter 91813Chicago Electric Inverter 91813 Instructions 91813, 2 |