Manualios.com

Utimaker 2 Operation & User’s Manual

Utimaker 2 Manual Online:

4.15, 2558 votes
Utimaker 2 User Manual
Utimaker 2 User Guide
Utimaker 2 Online Manual

Text of Utimaker 2 User Guide:

  • F1. In General To achieve the best possible results from your Ultimaker 2, some basic annual maintenance is recommended. This chapter contains tips which helps you to keep the Ultimaker 2 running at it’s best. Before you make a print a quick check is advised. A visual check is recommended to see if there is not any: - old prints/objects on the build plate. - make sur

  • C2. Installinglament:spoolholderandGuide Attaching the spool holder 1. The spool holder attaches to the back of the Ultimaker 2. 2. Take the spool holder and insert the top through the hole [2] in the middle of the back. 3. Now press it further down [3] until it snaps into place. The lament can now be added. When facing towards the back of

  • Utimaker 2, D2. Leveling the build plate (continued) Follow the display instruction 6/21 and 7/21, [CONTINUE] when nished. We are going to do this again to ne tune the build plate. Please, make sure you have a piece of paper within reach and press [CONTINUE] to go to the next step. Make sure you turn the build plate screw to netune this step if necessary. 8/21. Follow display instruction as demonstrated in the supporting image and press [CONTINUE] when nished. 9/21. Follow display instruction as demonstrated in the supporting image and press [CONTI

  • Utimaker 2, D3. Loadinglamentmaterial (continued) You can [CONTINUE] this step, 13/21, when the material is loaded until it reaches the rst bowden tube clip. 14/21. The lament is being pulled through the trans- parent bowden-tube more quickly. Wait until the progress bar is full. 15/21. Follow the instruction on the display. When the lament material exits from the nozzle, click the button to [CONTINUE]. Follow the display instruction 16/21 and 17/21. Make sure you choose the right material, this material type is usually indicated on the lament spool. Press the [READY] to choose the material. 18/21. C

  • Utimaker 2, F2. The glass plate After a lot of printing, there sometimes can be a little excess glue stuck to the glass build plate. This can cause an uneven print surface and it is recommended to clean it once in a while. 1. Make sure Ultimaker 2 power is powered o. 2. Carefully slide the front glass clamps and click them o carefully. 3. Make sure the building plate is at the bottom of your Ultimaker 2, this is to pre- vent you not damage you printhead or Z- axis. 4. Now you continue to slide the glass plate of the build plate to the front and take it out. 5. To disolve and

  • Utimaker 2, B1. Unboxing your Ultimaker 2 1. Place the Ultimaker 2 box on a stable surface, Placing it centrally on the oor will provide the best accessible position for unpacking. 2. Open the box. Here you will see the rst cardboard layer with a spool with PLA lament material and a welcome sheet. 3. Remove the rst cardboard layer. 4. Take out the Ultimaker 2 User manual which is placed at the side of the box. We recommend that you use the User manual to guide you through the setup process rst. NOTE: You can dow

  • Utimaker 2, F4. Lubricating the axes Z-Axis X-Y-Axes After approximately every half year the threaded rod on the z-stage has to be lubricated. A green grease (Magnalube-G) is included with the Ultimaker 2. This grease is the lubrication which has to be used on the threaded Z-stage rod. Note: the green grease should be applied as is shown in the photograph. Make sure you spread 10 drops of grease over the entire exposed threaded rod. With you next print on the Ultimaker 2 the Thread will grease itself by moving up and do

  • Utimaker 2, If the build plate is too far away from the nozzle your 3D-print might not stick to the build plate. Equally, if you adjust the build plate too close to the nozzle, the build plate can block the lament from extruding from the nozzle. It can also scratch the build plate. When leveling the build plate you must follow the step 4/21 until 10/21 on the display where the rst step 4/21 control the height by rotating this button. In the step 5/21 you rotate this left build plate screw under the build plate to control the height between the nozzle and the build plate. In 6/21 you adjust a similar bui

  • Utimaker 2, This is the main screen of Cura. Here you can choose which object or objects to print. And how you want them to be printed. 1. Load le Click this button to load an object to your print area. You can add as many objects as you can t on the plate. 2. Save toolpath (SD) When you press this button the prepared toolpath will be saved on the SD card. 3. Share on YouMagine.com Through this button you can share your 3D les on YouMagine. 4. Menu bar In this bar you can change to Full settings, preferences and more expert settin

  • Utimaker 2, D4.Makeyourrst3Dprint 19/21. It is important to tell your Ultimaker 2 which type of material it will be using. Ultimaker 2 will adjust its settings to match with specic materials. [CONTINUE] to go to the next step 20/21. Now that the Ultimaker 2 has leveled its build plate and has material lament loaded, it can now begin to 3D print. [ARE YOU READY] to go to the next step! 21/21. Make sure you have the SD-card inserted that came with your Ultimaker 2, If not, the SD-card can be inserted at the front of the Ultimaker 2 on the right side of the display in the SD-card slot. [LET’S PRINT] to start 3D prin

  • E1. DownloadingandinstallingCura The preferred software for your Ultimaker 2 is Cura from Ultimaker. This software package prepares your 3D model into instructions that your Ultimaker 2 uses to produce an object. 1. The Cura software package can be downloaded from the “Our software” section on our website: w w w . u l t i m a k e r . c o m /p a g e s /o u r- s o f t w a

  • 10. Now carefully remove the cardboard piece at the top back of the ultimaker 2, they are folded around the axis and the rubber belts. Caution: Do NOT use anything sharp to remove the cardboard, this could damage the rubber belts. 11. Uncut & remove the 2 plastic tiewraps that strap the XY axis and sliderblock together in the corners of the frame. Do NOT use anything sharp to

  • Utimaker 2, 12/21. In this step, you need to wait a minute while the printhead heats up. Wait for the onscreen pro- gress bar to reach 100% Please make sure you have a lament spool positioned over the spool holder, guided along the lament guide, with the lament in counter clockwise direction. 13/21. This step needs some extra focus. The wheel in the material feeder will start rotating slowly. Take the material and put it in the hole at the bottom of the material feeder. There is a hole where it should go

  • Utimaker 2, E5. FromSD-cardtoprintyourle 1. After saving the le and safely ejecting your SD-card from your computer, it is time to insert it in the SD-card Slot at the front of your Ultimaker 2. 2. By rotating the button and selecting [PRINT], you can now choose your desired print model from the SD-card. 32E5. From SD-card to print your le Make a printle with cura software Note. If you would like know more about Cura check the total Cura manual on our website: https://www.u

  • Utimaker 2, 5. Now remove the four cardboard corner pieces. 6. Now take out the box with the essential accesoires.. (check out the next chapter for content of this box) 7. Remove the cardboard sheet on top of the Ultimaker 2. 8. Now lift it gently up with 2 hands on the top of the Ultimaker 2 Caution: Make sure you lift ONLY by the frame DO NOT TOUCH any internal parts of ultimaker 2 9. Position it on a sturdy table to optimise the approach and with plenty of space surrounding it. NOTE: Please do not use excessive force when unpacking your Ultimaker 2. Excessive force may lead to damage to the Ultimaker 2 and its compo- nents. 9B1. Unboxing your Ulti

  • Utimaker 2, A2.SpecicationoftheUltimaker2 Printing Print technology Fused lament fabrication (FFF) Build volume 23 x 22,5 x 20,5 cm Layer resolution Ultra high High Medium Low Position precision X 12,5 micron Y 12,5 micron Z 5 micron Filament diameter 2.85 mm (generally known as 3 mm lament) Nozzle diameter 0.4 mm Print speed 30 mm/1 - 300 mm/s Travel speed 30 mm/1 - 350 mm/s Software Software package Cura - Ocial Ultimaker File types STL / OBJ / DAE / AMF Supports Windows (XP 32 bit/7+) Ubuntu Li

  • Utimaker 2, This User manual is designed to help you start your experience with Ultimaker 2. Within these pages, we want to show you how simple and easy it is to produce great prints. You might be familiar with earlier types of Ultimakers or other 3D-printers. It is essential that your read this manual carefully as there are a lot of new procedures with Ultimaker 2. A1. The Ultimaker Experience The Ultimaker experience Welcome to the Ultimaker 2 5

  • Utimaker 2, E2. Curasoftwareinterface (continued) The following mouse actions are used to work, navigate and view the 3D model: Leftmouse button Select objects. Hold and move the mouse to drag object on the 3D print area. Rightmouse button Hold and move the mouse to rotate the viewpoint around the 3D model. Right and left mouse button Hold and move the mouse to zoom. Scrollwheel button Use the scroll wheel to zoom in or out. Rightmouse button + Shift Hold and move the mouse to pan the 3D view. + 29E2. Cura software interface Make a printle with cura software

  • Utimaker 2, 16. Now gently slide the glass plate over the buildplate so that it snaps into the metal clamps at the back side of the build plate. 17. At last, close the metal clamps at the front to lock the glass plate in it’s position. 11B1. Unboxing your Ultimaker 2 Get started & unpack your Ultimaker 2

  • Utimaker 2, Not enough material is released from the nozzle. Cause Material feeder on the back of the Ultimaker 2 is ticking while printing. Nozzle is blocked or partially blocked by dirt or burned material. Solution Increasing the print temperature to 260C while printing in an attempt to clear the blockage. If the blockage is removed keep printing at 260C for at least 10 minutes to clean out any residue. Second cause Printing at 260C does not solve the blockage. Solution Something larger than 0.4mm could be blocking the nozzle. Cleaning the nozzle or replacing it is recommended. Contact support: sup

  • Utimaker 2, C3. Switchon/otheUltimaker2 Switch on the Ultimaker 2 Switch o the Ultimaker 2 The on/o button (a.k.a. ‘ – | O ’) of the Ultimaker 2 is located at the back. The ‘ O ’ re- presents o and the ‘ – ’ represents on. When it’s switched to the ‘ – ’ the Ultimaker 2 is turned on and should start up. After the Ultimaker 2 has been turned on, the front LED display should light up and the sides should glow. The Ultimaker 2 can be turned o by pressing the power switch to ‘ O ‘ at any time, it is recommended to only turn o the Ult

Related Products and Documents (3D Printers):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 CITROEN C1 Brochure citroen/c1-KT2.pdf 07 Dec 2022 20
2 Targus PA050U Quick start manual targus/pa050u-1OA.pdf 15 May 2023 2 1.12 Mb
3 Lavry DA2002 Operation manual lavry-engineering/da2002-AE1.pdf 12 Dec 2023 15
4 Cobra CPI 400 Operating instructions manual cobra/cpi-400-8H7.pdf 30 Jun 2023 12
5 Firestone 2239 Installation instructions firestone/2239-41L.pdf 22 Sep 2022 4
6 Kenwood KDC-DAB4551U Instruction manual kenwood/kdc-dab4551u-89N.pdf 29 Apr 2023 42

Similar Resources:

  • Polymaker

    PolyBox

    (2 pages)
    Thank you for purchasing the PolyBoxTM from Polymaker! With PolyBoxTM you’ll experience no more 3D printing problems caused by laments absorbing moisture such as extreme oozing, rough surface quality, weaker 3D prints, 3D printer damages and so on!Your PolyBoxTM package should contain the following:PACKAGE CONTENTSESSENTIAL PARTS OF THE POLYBOXTM12345PO …
  • Cellink

    BIO X

    (16 pages)
    Boston, U.S. 100 Franklin St., Boston, MA 02110 Gothenburg, Sweden Arvid Wallgrens Backe 20, Gothenburg, 41346 Virginia, U.S. 2000 Kraft Dr., Suite 2125 Blacksburg, VA 24060 Kyoto, Japan 46-29 Yoshida-Shimo Adachi-cho, Sakyo-ku, Kyoto www.cellink.com | +1 (833) CELLINK 1 BIO X Autocalibration Kit Installation and Quick-start Guide The Autocalibr …
  • TRAK

    3ntr Series

    (127 pages)
    TRAK® 3ntr 3D Printers Maintenance & Troubleshooting Manual Covers Current Models: • 3ntr A2 • 3ntr A4 2615 Homestead Place Rancho Dominguez, CA 90220-5610 USA T | 310.608.4422 | F | 310.764.2668 Service Department: 800.367.3165 e-mail: [email protected] | [email protected] | web: www.tra …
  • LeapFrog

    Creatr HS

    (9 pages)
    1 H. Kamerlingh Onnesweg 10 2408 AW Alphen aan den Rijn The Netherlands Creatr HS Flexible filament modification V01-04 Summary This document describes the modification of the Creatr HS 3D printer of Leapfrog BV to print flexible filament and written with the intention of use by customers. Contents 1. Introduction .................................. …
  • Creality

    CR-10 Series

    (16 pages)
    CR-10 Series 3D Printer User Manuall The User Manual is for the CR-10 Series of 3D printers. It is also applicable for the CR-10S/CR-10 S4/CR-10 S5. l But CR-10 mini without T-Bracket (Right) & Decoration Strip.l Due to the different types of devices、hardware and software upgrade, it is normal if the devices have little different. Please be subject to …
  • Flyingbear

    P902

    (7 pages)
    Installation InstructionFlyingBear P902 3D Printer一.Installation Steps of the 3D printer1.Check the installation video in the folder of“installation video”, then follow thesteps to install it.☆You should pay attention to the details in the installation process,there are hints in the InstallationVideo,you should watch the video carefully and follow th …

Comments, Questions and Opinions: