Siemens OOH740-A9-Ex Technical Manual
|
Siemens OOH740-A9-Ex, Specifications 8 Technical data for OOH740 - A9 - Ex 63 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 Ambient conditions Operating temperature -25…+70 °C Storage temperature -30…+75 °C Air humidity ≤95 % rel. Protection categories (IEC 60529): l Base FDB2x1, FDB2x1-AA, FDB2x2 with base attachment FDB291 IP43 l Base FDB2x1 with sealing kit FDBZ295 IP44 l Base FDB2x1, FDB2x1-AA, FDB2x2 with base attachment wet FDB295 IP44 Electromagnetic compatibility: l 1 MHz…2 GHz 50 V/m Permissible wind speed: Max. 20 m/s Mechanical data Color ∼RAL 9010 pure white Connections (in the detector base) Detector line and external alarm indicators: l Design Spring clips
Siemens OOH740-A9-Ex, Planning 4 Compatibility 33 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 4 Planning 4.1 Compatibility Compatible with control panels that support the C-NET-Ex detector line. Additionally, the point detector OOH740-A9-Ex can be operated on a collective detector line. The table below shows the compatibility of the point detector with various control panels: Detector line Control panel FC20xx FC72x SIGMASYS AlgoRex C-NET-Ex – X – – X = compatible – = not compatible You will find details in the 'List of compatibility'. Note the information provided in
Siemens OOH740-A9-Ex, 5 Mounting/Installation Sealing element FDBZ295 50 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 5.5 Sealing element FDBZ295 Sealing element FDBZ295 is used in conjunction with detector bases FDB2x1/FDB2x1-AA. The sealing element provides the device with protection against dirt and spray water. FDBZ295 2 5 3 FDB2x1 FDB2x1-AA 4 FDOOT241-A9-Ex OOH740-A9-Ex 8 1 7 6 4 mm Mounting of sealing element FDBZ295 Mounting w The kit is installed by hand 1. Fold the sealing lip back. 2. Insert the detector base into the sealing element. Make sure that the ope
Siemens OOH740-A9-Ex, Specifications 8 Technical data for OOH740 - A 9 - Ex 65 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 Collective maximum current connection factor/Alarm verification The default parameter set is set in all fire detectors in their as-delivered state. Use as Installed resistance value in the detector base Parameter set name K-MK Alarm verification permitted on control panel Smoke detector ∞ (no resistor installed) Sensitive (DO1101A-Ex replacement) 1.25 1 Yes Heat detector 18 kΩ,
Siemens OOH740-A9-Ex, Mounting/Installation 5 Collective and addressable detector base FDB201/221 47 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 5.2 Collective and addressable detector base FDB201/221 1. Route the recess-mounted cable or surface-mounted cable with an outer diameter of max. 6 mm directly into the detector base. 2. Ensure that the cables are flat on the bottom of the detector base. This way, they do not pose an obstruction when inserting the detector. FDB201/FDB221 max. 4mm Ø max. 6mmØ min. 46 max. 79 1 Installing the detector bases FDB201 and FDB221 1 Detector base
Siemens OOH740-A9-Ex, 3 Structure and function Accessories 28 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 3.3 Accessories 3.3.1 Addressable detector base FDB221 l For the mounting of point detectors l For the recess-mounted cable entry l For surface-mounted cable entry, up to 6 mm cable diameter l Orange terminal block l Order no. FDB221: A5Q00001664 See also 2 Collective and addressable detector base FDB201/221 [➙ 47] 3.3.2 Collective detector base FDB201 l For the mounting of point detectors l For the recess-mounted ca
Siemens OOH740-A9-Ex, About this document 1 Revision history 13 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 1.4 Revision history The reference document's version applies to all languages into which the reference document is translated. The first edition of a language version or a country variant may, for example, b e version 'd' instead of 'a' if the reference document is already this version. The table below shows this document's revision history: Modification index Edition date Brief description h 2015-02-02 Table listing published language versions corrected; base attachment
Structure and function 3 Function 25 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 3.2.2 Danger levels The detector's signal processing efficiently distinguishes between fire events and deceptive phenomena. The basis for reaching a danger level is not only given by measured values exceeding a "response threshold"; moreover, the s
Siemens OOH740-A9-Ex, 8 Specifications Technical data for OOH740 - A9 - Ex 64 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 Collective detector line You will find more information in document 001204. Detector line Operating voltage DC 14...28 V Maximum current connection factor 1.25 Quiescent current at maximum current connection factor 65…125 μA Surge current at maximum current connection factor 180 μA You will find details in the corresponding section Alarm voltage at: l Alarm current = 1…15 mA DC 5…11 V l Alarm current = 25 mA DC 9…12 V Alarm current limitation at operating voltage = DC 13...28 V 30
Siemens OOH740-A9-Ex, Mounting/Installation 5 Base attachment FDB291 49 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 5.4 Base attachment FDB291 l For cable diameters > 6 mm, the base attachment FDB291 is required. l The required cable entries must be broken out on the base attachment FDB291. 119 25 max. 90 min. 46 max. Ø 4mm FDB291 max. Ø 21mm FDB2x1 FDB2x2 1 2 3 Mounting of detector base on base attachment FDB291 1 Identification 3 Detector base 2 Base attachment
3 Structure and function Setup 22 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 Switching over the parameter set In addition to selecting the parameter set, the point detectors with ASAtechnology enable time- or process-controlled switching over of the parameter sets (Manned/Unmanned switchover). The time- or process-controlled switching
Siemens OOH740-A9-Ex, Safety 2 Safety regulations for the method of operation 17 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 Testing the product operability l Prevent the remote transmission from triggering erroneously. l If testing building installations or activating devices from third-party companies, you must collaborate with the people appointed. l The activation of fire control installations for test purposes must not cause injury to anyone or damage to the building installations. The following instructions must be observ
Siemens OOH740-A9-Ex, 2 Safety Standards and directiv es complied with 18 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 Disclaimer We have checked that the content of this document matches the hardware and software described. Despite this, we cannot rule out deviations and cannot therefore assume liability for them matching completely. The details in this document are checked regularly and any corrections needed included in subsequent editions. We are grateful for any suggestions for improvement. 2.3 Standards and directives complied with A list of the standards and directives complied
Siemens OOH740-A9-Ex, 2 Safety Safety instructions 14 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 2 Safety WARNING Contradictory safety instructions Risk of explosion caused by disregarding safety instructions ● Should safety instructions relating to explosion protection contradict other safety instructions, please observe the safety instructions relating to explosion protection. 2.1 Safety instructions The safety notices must be observed in order to protect people and property. The safety
Issued by Siemens Switzerland Ltd Building Technologies Division International Headquarters Gubelstrasse 22 CH-6301 Zug Tel. +41 41-724 24 24 www.siemens.com/buildingtechnologies © Siemens Switzerland Ltd, 2012 Technical specifications and availability subject to change without notice. Document ID A6V10367521_h_en_-- Manual FD720 Edition 2015-02-02 Section 8
Index 69 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 Index A Approvals, 62, 63 ASAtechnology, 19, 21 C CE marking, 62 Collective behavior Degraded mode operation, 27 Collective detector lines Danger levels, 25 Compatibility, 33, 59 Connection Addressed detector line, 56 Collective detector line, 57 Customer Support Center Service, 7 D Danger level Collective detector line
Siemens OOH740-A9-Ex, 4 Planning Default settings 42 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 4.5 Default settings The detector operates in the default parameter set as long as the control panel has not assigned a valid parameter set to the detector. The following table shows the default parameter set for the point detector OOH740-A9-Ex in the various sensor modes: Fire detector Default parameter set OOH740-A9-Ex in C-NET-Ex operation mode High Compensation OOH740-A9-Ex in collective operation (no resi
Siemens OOH740-A9-Ex, 5 Mounting/Installation Designation plate FDBZ291 52 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 5.7 Designation plate FDBZ291 To provide the detector with a location address, the address is inscribed on the designation plate FDBZ291 and placed on the detector base or base attachment. FDB291 FDBZ291 FDB2x1 FDB2x2 FDBZ291 1 2 1 3 4 Mounting of designation plate FDBZ291 1 Designation plate FDBZ291 3 Identification 2 Base attachment FDB291 4 Detector base 5.8 Designation plate DBZ1193A To identify a detector on a base attachment humid, the designation plate DBZ1193A is label
Siemens OOH740-A9-Ex, Structure and function 3 Accessories 31 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 3.3.11 Dummy detector FDX291 F D X 2 9 1 S 5 4 3 1 9 - F 2 - A 1 l To protect the detector base from dirt l External labelling for identification l Does not open the contact in the detector base l Order no.: S54319-F2-A1 3.3.12 Detector dust cap FDZ291 l To protect the point detector OOH740-A9-Ex from dust l Order no.: A5Q00004814 See also 2 Detector dust cap FDZ291 [➙ 53] 3.3.13 Connection terminal DBZ1190-AB l Auxiliary terminal for connecting cables l For T-branches of additional cabling l For wire diameters of 1…2.5 mm² l 3 p
Siemens OOH740-A9-Ex, Index 70 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 P Packaging label Product version, 23 Parameter set Detection behavior of the point detector, 24 Parameter sets Addressed, 35 Collective, 41 Product label Product version, 23 R Recess-mounted supply lead Detector base FDB202/222, 48 Recycling, 66 Renovation mode Major renovation work, 26 Replacing point detectors, 41 S Service Customer Support Center, 7 Signal processing of the detector Danger level, 25 Source language, 9 Standards, 63 Surface-mounted or recess-mounted supply lead Detector base FDB201
Siemens OOH740-A9-Ex, Planning 4 Technical Ambient Super vision Message 43 Building Technologies A6V10367521_h_en_-- Fire Safety 2015-02-02 4.6.1 Ambient conditions In markets where the use of the 'Technical Ambient Supervision Message' is permitted, the point detector can be positioned above or near objects which require the ambient temperature to be monitored in order to prevent damage. 'Technical Ambient Supervision Message' mode detects an increase or decrease in temperature. You can set the following parameter
DOWNLOAD |
Siemens FDF241-9 Security Sensors Technical manual
FDF241-9 |
Siemens SITRANS F FUH1010 Series Security Sensors Operating instructions manual
SITRANS F FUH1010 Series |
Siemens AlgoRex CS1140 Security Sensors Planning
AlgoRex CS1140 |
Siemens DB-11 Security Sensors Installation/wire connection manual
DB-11 |
Siemens FDM243H Security Sensors Technical manual
FDM243H |
Siemens FS20 Security Sensors Planning manual
FS20 |
Siemens FDOOTC441 Security Sensors Installation instructions
FDOOTC441 |
Siemens 13-xx-ST-SBT Series Security Sensors Product data
13-xx-ST-SBT Series |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | MiLAN | MIL-140 | Installation manual | milan/mil-140-9BX.pdf | 28 Oct 2023 | 1 | |
2 | Sony | CHU-ZCT1E | Instruction manual | sony/chu-zct1e-Y4I.pdf | 05 Oct 2023 | 2 | |
3 | SCIFIT | ISO7000R | Service manual | scifit/iso7000r-2JB.pdf | 31 Jul 2023 | 30 | |
4 | JRC | NSVS1102 | Manual | jrc/nsvs1102-432.pdf | 28 Jan 2024 | 4 | |
5 | Hitachi | ACV01U - LCD Direct View TV | Operating manual | hitachi/acv01u-lcd-direct-view-tv-C3P.pdf | 11 Apr 2023 | 44 | 9.99 Mb |
6 | SEKURE | Paradox Esprit 616LED | Operation & user’s manual | sekure/paradox-esprit-616led-MM8.pdf | 25 Jun 2023 | 20 | 0.21 Mb |
Saso
Photoelectric Beam DetectorSASO-PB10S/PB30S/PB60SInstallation InstructionsPlease note : This sensor is designed to detect intrusion and to initiate an alarm, it is not a burglar-preventing device. Maker is not responsible for damage, ,injury or losses caused by accident, theft, natural disasters, abuse, misuse, abnormal usage, faulty installation or imprope …
SASO-PB10S(2 pages) |
TIF
TIF XP-1AAutomatic Halogen Leak DetectorOwner’s ManualManual del PropietarioGuide de l'utilisateurBedienungsanleitung100599TIF REVAMiramar, FloridaToll Free: 800-327-5060Phone: 954-499-5400 Fax: 954-499-5454www.tif.comDesigned & Engineered in the USAManufactured in ChinaADVANCETESTPRODUCTS
…
TIF XP-1A(20 pages) |
MDT Technologies
MDT technologies GmbH, Geschäftsbereich Gebäudeautomation Tel.: + 49 - 2263 - 880 • Fax: + 49 - 2263 - 4588 • E-Mail: [email protected] • www.mdtautomation.deStand: 1010 Technische Daten Technical Data SCN-PM360D.01 SCN-PM360K.01Konguration CongurationLichtsensorLight sensorLichtsensor mit Konstantlichtregelung Light sensor with constant lig …
SCN-PM series(2 pages) |
Nice
DE - Installierungs-und Gebrauchsanleitungen und HinweiseEN - Instructions and warnings for installation and useIT - Istruzioni ed avvertenze per l’installazione e l’usoFR - Instructions et avertissements pour l’installation et l’utilisationES - Instrucciones y advertencias para la instalación y el usoPL - Instrukcjeiostrzeżeniado� …
MOONBUS MOFOB(20 pages) |
Elko
02-30/2017 Rev.1RFWD-100Window / Door detectorENMade in Czech RepublicON1 2+CR2032Click!Characteristics / • The window / door detector is used to detect opening where activation occurs when the mag-net and the sensor become separated.• Use:- in combination with the switching unit for automatic light control (cellar, garage, etc.), or switching on a G …
INELS RFWD-100(5 pages) |
Basalte
© 2020basalte v7.0A Programming buttonB Programming LEDC KNX connectorD Mounting clipE Central IR window Safety instructionsBefore operating the unit, please read this manual thoroughly and retain it for future reference.Failure to observe these instructions might damage the device.The device may only be installed and connected by professional electri …
AURO KNX Series(2 pages) |
Zears Cell Phone FIZZ S 111Zears FIZZ S 111 Guide (Doc Type: Cell Phone Operation & user’s manual) FIZZ S 111, 24 |
Zooper Smoke Alarm Premier M+User Guide: Zooper Premier M+ (58J4Z2, Upd.22nd Sep 2023) Premier M+, 16 |
Craftsman Air Compressor 919.184160Air Compressor Owner's manual (Craftsman 919.184160) 919.184160, 18 |
Samsung LCD TV LE37R7PDF Guide (@VF2LX8), Samsung LE37R7 LCD TV (27.12.2023) LE37R7, 85 |
RCA LCD TV RLC2685ARLC2685A (LCD TV ePDF Manual, #2A6U5W) RLC2685A, 19 |
Yealink IP Phone SIP-T19PYealink SIP-T19P IP Phone Operation & user’s manual SIP-T19P, 124 |
Universal Keypad KP-4000Guide: Universal KP-4000 (45W471, Upd.11.09.2023) KP-4000, 24 |
Skytec Subwoofer SM serie#Y5F392: SM serie Subwoofer Instruction manual SM serie, 10 |
Nokia Cell Phone N95N95 (Cell Phone ePDF Manual, #HO47W2) N95, 140 |
Hoppekids Indoor Furnishing ChristianChristian (Indoor Furnishing ePDF User Guide, #99F6GZ) Christian, 5 |
Vauxhall Automobile VIVAROVauxhall Automobile Owner's manual (File: vauxhall-vivaro-owner-s-manual-182, Fri 12.2023) VIVARO, 182 |
Philips Home Lighting 405421213Home Lighting PDF Specifications 405421213, 3 |