Siemens milltronics Instruction Manual

Text of Siemens milltronics User Guide:

• Siemens milltronics, Page 12 Milltronics MLC Belt Scale – INSTRUCTION MANUAL 7ML19985FF01 Metric Designs (Europe) Imperial Designs (North America) Belt Width A Dimension B Dimension C Dimension D Dimension E Dimension 450 mm (17.72 ") 450 mm (17.72") 500 mm (19.69") 50 mm (1.97") 158 mm (6.22") 96 mm (3.78") 500 mm (19.69 ") 500 mm (19.69") 550 mm (21.65") 50 mm (1.97") 158 mm (6.22") 96 mm (3.78") 650 mm (25.59 ") 650 mm (25.59") 700 mm (27.56") 50 mm (1.97")

• Siemens milltronics, 7ML19985FF01 Milltronics MLC Belt Scale – INSTRUCTION MANUAL Page 9 • The tube is designed to move very slightly in its mounting to eliminate mutual interference between the cells. 2. Slowly slide it all the way in until it contacts the end of the tube. • Approximately 10 mm (3/8") of the rod should protrude from the tube. 3. Perform the span calibration as described in the calibration section of the selected integrator instruction manual. 4. After the span calibration has been completed, remove the calibrating test

• Siemens milltronics, i Table of Contents Introduction ..........................................................................................................................1 The Manual ...............................................................................................................................................1 Milltronics MLC Belt Scale ...................................................................................................................1 Specifications ......................................................................................................................2 Operation ....................................................

• Siemens milltronics, 7ML19985FF01 Milltronics MLC Belt Scale – INSTRUCTION MANUAL Page 7 Plan View this idler supplied by Siemens Milltronics 25mm TYP. (1 ") (both sides) aligning wire 0.5mm dia. (0.020 ") or equivalent (customer supplied) low capacity belt scale

• Siemens milltronics, © Siemens Milltronics Process Instruments Inc. 2008 Safety Guidelines: Warning notices must be observed to ensure personal safety as well as that of others, and to protect the product and the connected equipment. These warning notices are accompanied by a clarification of the level of caution to be observed. Qualified Personnel: This device/system may only be set up and operated in conjunction with this manual. Qualified personnel are only authorized to install and operate this equipment in accordance with established safety practices and standards. Unit Repair and Excluded Liability: • The user is responsible for all changes and repairs made to the devic

• Siemens milltronics, 7ML19985FF01 Milltronics MLC Belt Scale – INSTRUCTION MANUAL Page 13 Index A animal feed pellets ...........................................1 approvals ............................................................2 B belt speed ...........................................................2 belt width ............................................................2 C calibrating test rod .....................................1, 8 calibration ..........................................................8 capacity ..............................................................2 conveyor incline ...............................................2 F fertilizer .................

• Siemens milltronics, 7ML19985FF01 Milltronics MLC Belt Scale – INSTRUCTION MANUAL Page 3 Operation The MLC belt scale works with an existing light-duty flat belt conveyor (handling light- density materials) and the selected Siemens Milltronics integrator. As material moving along the conveyor belt travels over the belt scale, it exerts a force proportional to the material load through the suspended idler to the load cells. The MLC reacts only to the vertical component of the applied force. The resulting movement in each load cell is sensed by its strain gauges. When the strain gauges are excited by voltage from the electronic integrator, they produce an electrical signal

• Siemens milltronics, 7ML19985FF01 Milltronics MLC Belt Scale – INSTRUCTION MANUAL Page 11 Dimensions Notes: • For dimension values see next page. * For pan supported belts, the pan should be cut out to allow the MLC and at least two (preferably four) other idlers to be installed. Installation Plan View Front View idler diameter C location of removed idler MLC Belt Scale 20.6mm (0.812 ") E 4 x dia. 11mm (0.44 ") 64mm (2.5 ") D * (see Note below) A B

• Siemens milltronics, Page 10 Milltronics MLC Belt Scale – INSTRUCTION MANUAL 7ML19985FF01 Wiring customer junction box load cell B load cell A r e d ‘A’ r e d ‘B’ b l k ‘A’ b l k ‘B’ w h t ‘A’ g r n ‘A’ w h t ‘B’ g r n ‘B’ s h l d ‘A’ s h l d ‘B’ s h i e l d + s i g ‘B’ - s i g ‘A’ - e x c + e x c - s i g ‘B’ + s i g ‘A’ load cell A belt travel load cell B

• Page 2 Milltronics MLC Belt Scale – INSTRUCTION MANUAL 7ML19985FF01 Specifications Accuracy • ±1.0% of totalization over 5 to 1 operating range Belt Width • metric: 450 to 1200 mm • imperial: 18 to 48" Belt Speed • 2.0 m/s (400 fpm) maximum Capacity • up to 50 t/h (depending on loading and belt speed parameters) Conveyor Incline • ±20º

• Siemens milltronics, *7ml19985FF01* Rev. 1.2 www.siemens.com/processautomation Siemens Milltronics Process Instruments Inc. 1954Technology Drive, P.O. Box 4225 Peterborough, ON, Canada K9J 7B1 Tel: (705) 745-2431 Fax: (705) 741-0466 Email: [email protected] Siemens Milltronics Process Instruments Inc. 2008 Subject to change without prior notice Printed in Canada

• Siemens milltronics, 7ML19985FF01 Milltronics MLC Belt Scale – INSTRUCTION MANUAL Page 1 Introduction The Manual The Milltronics MLC belt scale is used in conjunction with the selected integrator and speed sensor. This manual covers only MLC installation and operating procedures. Integrator and speed sensor instruction manuals can be downloaded from www. siemens.com/continuous-weighing . This manual will help you set up your MLC for optimum performance. We always welcome suggestions and comments about manual content, design, an

• Siemens milltronics, 7ML19985FF01 Milltronics MLC Belt Scale – INSTRUCTION MANUAL Page 5 Installation Procedure 1. Make sure the shipping stops are in place and secure. 2. Remove the existing flat roll idler (or flat slider pan) from the area selected to locate the belt scale assembly. 3. Drill four 12 mm (7/16") diameter mounting holes. This will allow clearance for 10 mm (3/8") bolts. 4. Position the scale with the idler towards the head end of the conveyor and the static beam toward the tail end. • Make sure the belt travel

• Siemens milltronics, Page 4 Milltronics MLC Belt Scale – INSTRUCTION MANUAL 7ML19985FF01 Welding Load Cell Handling The MLC belt scale is designed for low-capacity operation and is constructed using two 10 or 20 pound load cells. Although the load cells are protected by shipping stops that keep the cells from moving, care should be taken when handling the scale to avoid damaging the cells. The stops are metal strips about 75 mm (3") long with holes at each end for screws. One screw holds the stop to the load cell while the other screw holds the stop to the static beam (125 mm [5"] channel). When handling the MLC during installatio

• Siemens milltronics, Page 6 Milltronics MLC Belt Scale – INSTRUCTION MANUAL 7ML19985FF01 Idler Alignment Precise alignment is very important to achieve maximum accuracy of the weighing system. Improperly aligned idlers could cause unwanted forces to be applied to the weighing idler, resulting in measurement errors. Alignment Procedure 1. Remove the shipping stops to free the weighing mechanism. • Keep the stops and screws stored in a convenient place for use during maintenance or at other times when protection of the cells is necessary . 2. Align and level the idler in the weighing area by raising or lowering the

Related Products and Documents (Scales):

Comparable Devices:

Similar Resources:

• Rice Lake IQ plus 2100 (43 pages) PRESENTED BYJPBOWLIN.COM817.332.8116J.P. Bowlin is a quality-driven Calibration Companythat has provided calibration, repair and salesof all types of weighing and measurement products since 1931. …

• Epson DM-D110 (2 pages) ENStart HereFor information on safety recommendations and basic operations, see User's Manual included on Manual CD. For detailed information, see Technical Reference Guide. You can access Technical Reference Guide from the included Manual CD.FRCommencer IciPour obtenir des informations sur les recommandations concernant la sécurité et le fonctionneme …

• Salter MyBody (11 pages) Eplease read this instruction manual beforeusing the product for the first time9119 BK3RBody Analyser Scale with USB PC Data TrackingInstruction Manual and Guarantee …

• CPS COMPUTE-A-CHARGE CC840W (12 pages) OWNER’S MANUAL (English)Français, Español, Deutsch, Português, Русский, and latest updates: www.cpsproducts.comTO BE OPERATED BY QUALIFIED PERSONNEL ONLYVersion 4.3 or higher …

• Nahita Series 5034 (14 pages) FRANÇAISPage 28 Manual d’usage 55034XXX Revision 1 Mars-047. RÉSOLUTION DE PROBLÈMESPROBLÈME CAUSE SOLUTIONOn ne voit pas les chiffres surl'écran.- Vérifiez que le courentélectrique arrive jusqu'à labalance. L'adaptateur peutêtre abîmé.- Le fusible est abîmé.- Ajustez les vis …

• CAS SW-1S Series (34 pages) 859306-15-20 nl ma 2012-07 1/2*HEUXLNHUVKDQGOHLGLQJYRRUGH&$66:VHULH)XQFWLHWRHWVHQ 2PVFKULMYLQJ=(52   9RRUKHWQXOVWHOOHQYDQGHZHHJVFKDDO7$5(   9RRUKHWLQHQXLWVFKDNHOHQYDQKHWWDUUDJHZLFKW+2/' :DQQHHUKHWJHZLFKWQLHWVWDELHOODDW� …

Comments, Questions and Opinions: