Siemens RUGGEDCOM RX5000 Installation Manual

Text of Siemens RUGGEDCOM RX5000 User Guide:

• RUGGEDCOM RX5000 Installation Guide Chapter 1 Introduction Feature Highlights 1 Introduction The RUGGEDCOM RX5000 is a high-port density routing and switching platform, designed to operate in harsh environments.The RX5000 can withstand high levels of electromagnetic interference, radio frequency interference, and a wide temperature range of -40 to 85 °C (-40 to 185 °F). The RX5000 is

• Siemens RUGGEDCOM RX5000, Chapter 4 Technical Specifications RUGGEDCOM RX5000 Installation Guide 30 Fiber Optic Ethernet Port Specifications Order Code Speed e Connector Duplex e Cable Type f Wiring Standard g Maximum Distance h Isolation i SM02 10/100/1000Base-T RJ45 FDX/HDX > Category 5 TIA/EIA T568A/B 100 m (328 ft) 1.5 kV SM32 10/100/1000Base-T RJ45 FDX/HDX > Category 5 TIA/EIA T568A/B 100 m (328 ft) 1.5 kV e Auto-negotiating. f Shielded or unshielded. g Auto-crossover and auto-polarity. h Typical distance. Depend

• Siemens RUGGEDCOM RX5000, RUGGEDCOM RX5000 Installation Guide Chapter 4 Technical Specifications Power Supply Specifications 29 Technical Specifications The following sections provide important technical specifications related to the device and available modules: • Section 4.1, “Power Supply Specifications” • Section 4.2, “Failsafe Relay Specifications” • Section 4.3, “Copper Ethernet Port Specifications” • Section 4.4, “Fiber Optic Ethernet Port Specifications” • Section 4.5, “Serial Port Specifications” • Section 4.6, “Operating Environment” • Section 4.7, “Mechanical Specifications” Section 4.1 Power Supply Specifications Input

• Siemens RUGGEDCOM RX5000, Chapter 6 Certification RUGGEDCOM RX5000 Installation Guide 36 Industry Canada Compliance Section 6.3 Industry Canada Compliance CAN ICES-3 (A) / NMB-3 (A) Section 6.4 EMI and Environmental Type Tests The RX5000 has passed the following EMI and environmental tests. IEC 61850-3 EMI Type Tests Test Description Test Levels Severity Levels Enclosure Contact +/- 8 kV 4 IEC 61000-4-2 ESD Enclosure Air +/- 15 kV 4 IEC 61000-4-3 Radiated RFI Enclosure Ports 20 V/m Note a Signal ports +/- 4 kV @ 2.5 kHz Note a DC Power ports +/- 4 kV 4 AC Power ports +/-

• RUGGEDCOM RX5000 Installation Guide Chapter 5 Dimension Drawings 33 Dimension Drawings NOTE All dimensions are in millimeters, unless otherwise stated. 175.3 25.4 177.8 479.8 469.6 133.4 117.6 101.6 12.7 16.0 16.0 31.8 5.8 10.9 446.8 441.7 221.5 311.9 Figure 30: Overall Dimensions

• Siemens RUGGEDCOM RX5000, RUGGEDCOM RX5000 Installation Guide Chapter 2 Installing the Device 5 Installing the Device The following sections describe how to install the device, including mounting the device, connecting power, and connecting the device to the network. DANGER! Electrocution hazard – risk of serious personal injury and/or damage to equipment. Before performing any maintenance tasks, make sure all power to the device has been disconnected and wait approximately two minutes for any remaining energy to dissipate. WARNING! Burn hazard – risk of serious personal injury. Avoid contact

• Siemens RUGGEDCOM RX5000, RUGGEDCOM RX5000 Installation Guide Chapter 3 Communication Ports Connecting Multiple RS485 Devices 27 1 2 3 Figure 28: Removing a Module 1. Chassis 2. Module 3. Screw 5. Install a new module or a blank module (to prevent the ingress of dust and dirt). For more information, refer to Section 3.6.1, “Installing a Module”. 6. If necessary, install the device in the rack. 7. Connect power to the device. Section 3.7 Connecting Multiple RS485 Devices Each RS485 port can communicate with multiple RS485 devices by wiring devices together in sequence over a single twisted pair with transmit and receive signals

• Siemens RUGGEDCOM RX5000, RUGGEDCOM RX5000 Installation Guide Chapter 2 Installing the Device Installing/Removing Power Supplies 9 • For 125/250 VDC rated equipment, an appropriately rated DC circuit breaker must be installed. • It is recommended to provide a separate circuit breaker for each power supply module. • Equipment must be installed according to applicable local wiring codes and standards. The following sections describe how to connect power to the device: • Section 2.2.1, “Installing/Removing Power Supplies” • Section 2.2.2, “Connecting AC Power” • Section 2.2.3, “Connecting DC Power” Section 2.2.1 Installing/Removing Power Su

• Siemens RUGGEDCOM RX5000, Chapter 2 Installing the Device RUGGEDCOM RX5000 Installation Guide 10 Removing a Power Supply NOTE The power supplies are hot swappable. It is not necessary to disconnect power to the device before installing or removing a power supply. 1. Remove the blank power module assembly or, if equipped, the currently installed power supply. For information about removing a power supply, refer to Section 2.2.1.2, “Removing a Power Supply”. 2. Insert the power supply into the empty slot. When power is supplied to the device, the top and bo

• Siemens RUGGEDCOM RX5000, Chapter 3 Communication Ports RUGGEDCOM RX5000 Installation Guide 20 Serial Ports • Section 3.6, “Installing/Removing Modules” • Section 3.7, “Connecting Multiple RS485 Devices” Section 3.1 Serial Ports The RX5000 supports DB9 serial ports, which can be run in RS232, RS485 or RS422 mode. NOTE On power-up, all serial ports default to RS485 mode. Each port can be individually set to RS232, RS485 or RS422 mode through ROX II. For more information, refer to the ROX II User Guide for the RX5000. All serial ports feature an LED that indicates the current state of

• Siemens RUGGEDCOM RX5000, Chapter 4 Technical Specifications RUGGEDCOM RX5000 Installation Guide 32 Mechanical Specifications Section 4.7 Mechanical Specifications Parameter Value Dimensions Refer to Chapter 5, Dimension Drawings. Weight 14-16 kg (30-35 lbs) Ingress Protection IP40 Chassis Material Aluminum

• Siemens RUGGEDCOM RX5000, Chapter 2 Installing the Device RUGGEDCOM RX5000 Installation Guide 14 Connecting the Failsafe Relay 2 1 Figure 10: Chassis Ground Connection 1. #8-32 Screw 2. #8 Ring Lug Section 2.4 Connecting the Failsafe Relay The failsafe relay on the Control Module (CM) can be configured to latch based on alarm conditions. The NO (Normally Open) contact is closed when the unit is powered and there are no active alarms. If the device is not powered or if an active alarm is configured, the relay opens the NO contact and closes the NC (Normally Closed) c

• Siemens RUGGEDCOM RX5000, Chapter 2 Installing the Device RUGGEDCOM RX5000 Installation Guide 6 Mounting the Device Section 2.1 Mounting the Device The RX5000 is designed for maximum mounting and display flexibility. It can be equipped with adapters that allow it to be installed in a 48 cm (19 in) rack or directly on a panel. NOTE For detailed dimensions of the device with mounting hardware installed, refer to Chapter 5, Dimension Drawings. The following sections describe the various methods of mounting the device: • Section 2.1.1, “Mounting the Device to a Rack” • Sec

• Siemens RUGGEDCOM RX5000, RUGGEDCOM RX5000 Installation Guide Chapter 6 Certification Agency Approvals 35 Certification The RX5000 device has been thoroughly tested to guarantee its conformance with recognized standards and has received approval from recognized regulatory agencies. • Section 6.1, “Agency Approvals” • Section 6.2, “FCC Compliance” • Section 6.3, “Industry Canada Compliance” • Section 6.4, “EMI and Environmental Type Tests” Section 6.1 Agency Approvals The RX5000 has received approval from various agencies. Agency Standards Comments TUV

• Siemens RUGGEDCOM RX5000, RUGGEDCOM RX5000 Installation Guide Chapter 2 Installing the Device Gigabit Ethernet 1000Base-TX Cabling Recommendations 17 • Shielded/screened cabling can be used when required. Care should be taken to avoid the creation of ground loops with shielded cabling.

• RUGGEDCOM RX5000 Installation Guide Chapter 2 Installing the Device Connecting to the Device 15 Serial Console and Management Ports Connect a PC or terminal directly to the serial console or management ports to access the boot-time control and ROX II interfaces. The serial console port provides access to ROX II 's console interface, while the management port prov

• Siemens RUGGEDCOM RX5000, RUGGEDCOM RX5000 Installation Guide Chapter 3 Communication Ports Installing/Removing Modules 25 CAUTION! Electrical hazard – risk of damage to equipment. Make sure all electrostatic energy is dissipated before performing installing or removing components from the device. An electrostatic discharge (ESD) can cause serious damage to the component once it is outside the chassis. 1. Make sure all potential electrostatic build-up has been properly discharged to prevent electrostatic discharges (ESD). This can be accomplished by wearing an ESD wrist strap or by touching Earth or the chassis ground. 2. Disconnect the cable from the port. 3. Swing the metal bail-latch down and pull

• Siemens RUGGEDCOM RX5000, Preface RUGGEDCOM RX5000 Installation Guide vi Training For any questions about the documentation or for assistance finding a specific document, contact a Siemens sales representative. Training Siemens offers a wide range of educational services ranging from in-house training of standard courses on networking, Ethernet switches and routers, to on-site customized courses tailored to the customer's needs, experience and application. Siemens' Educational Services team thrives on providing our customers with the essential practical skills to make sure users have the right knowledge and expertise to understand the various technologies associated with critical communications

• Chapter 6 Certification RUGGEDCOM RX5000 Installation Guide Test Description Test Levels DC Power ports 2 kVDC AC Power ports 2 kVAC Environmental Type Tests Test Description Test Levels IEC 60068-2-1 Cold Temperature Test Ad -40 °C (-40 °F), 16 Hours IEC 60068-2-2 Dry Heat Test Bd 85 °C (185 °F), 16 Hours IEC 60068-2-30 Humidity (Damp Heat, Cyclic) Test Db 95% (no

• Siemens RUGGEDCOM RX5000, RUGGEDCOM RX5000 Installation Guide ii Copyright © 2014 Siemens AG All rights reserved. Dissemination or reproduction of this document, or evaluation and communication of its contents, is not authorized except where expressly permitted. Violations are liable for damages. All rights reserved, particularly for the purposes of patent application or trademark registration. This document contains proprietary information, which is protected by copyright. All rights are reserved. No part of this document may be

• Siemens RUGGEDCOM RX5000, Chapter 1 Introduction RUGGEDCOM RX5000 Installation Guide 2 Ports, Controls and Indicator LEDs ▪ Meets IEEE 1613 (electric utility substations) ▪ Exceeds IEC 61850-3 (electric utility substations) ▪ Exceeds IEC 61800-3 (variable speed drive systems) ▪ Exceeds IEC 61000-6-2 (generic industrial environment) • -40 to 85 °C (-40 to 185 °F) operating temperature (no fans within chassis or modules) • Conformal coated printed circuit boards (optional) Management Tools • Web-based, SSH and CLI management interfaces • SNMP v1, v2 and v3 • Rich set of diagnostics with configurable logging • NETCONF M

• Siemens RUGGEDCOM RX5000, RUGGEDCOM RX5000 Installation Guide Chapter 6 Certification EMI and Environmental Type Tests 37 Test Description Test Levels Severity Levels DC Power ports 2.5 kV common, 1 kV differential mode @1MHz 3 AC Power ports 2.5 kV common, 1 kV differential mode @1MHz 3 Signal ports 30 V Continuous, 300 V for 1 s 4 IEC 61000-4-16 Mains Frequency Voltage DC Power ports 30 V Continuous, 300 V for 1 s 4 IEC 61000-4-17 Ripple on DC Power Supply DC Power ports 10% 3 Signal ports 2 kVAC (Fail-Safe Relay output) DC Power ports 1.5 kVDCDielectric Strength AC Power ports 2 kVA

• Siemens RUGGEDCOM RX5000, RUGGEDCOM RX5000 Installation Guide Chapter 3 Communication Ports SFP Optic Ethernet Ports 23 21 Figure 20: MTRJ Port 1. Tx Connector 2. Rx Connector 21 Figure 21: LC Port 1. Tx Connector 2. Rx Connector 21 Figure 22: SC Port 1. Tx Connector 2. Rx Connector 21 Figure 23: ST Port 1. Tx Connector 2. Rx Connector For specifications on the available fiber optic Ethernet ports, refer to Section 4.4, “Fiber Optic Ethernet Port Specifications”. Section 3.5 SFP Optic Ethernet Ports SFP (Small Form-Factor Pluggable) optic Ethernet ports are available with LC (Lucent Connector) conn

• Siemens RUGGEDCOM RX5000, RUGGEDCOM RX5000 Installation Guide Chapter 3 Communication Ports 19 Communication Ports The RX5000 can be equipped with various types of communication ports to enhance its abilities and performance. Each set of communication ports is part of a field replaceable module that makes switching ports fast and easy. Use the ROX II software to determine which ports are equipped on the device. For more information, refer to the ROX II User Guide for the RX5000. Each type of module has a specific location in the RX5000 chassis. 1 2 3 4 5 6 7 Figure 14: Module Assignment 1. Ethernet Module Slot (LM1) 2. Ethernet Module Slot (LM2) 3. Ethernet Module Slot (LM3) 4. Swi

• Siemens RUGGEDCOM RX5000, Chapter 2 Installing the Device RUGGEDCOM RX5000 Installation Guide 8 Connecting Power 1 2 2 Figure 4: Panel Mounting 1. Screw 2. Adaptor 2. Install the supplied screws to secure the adapters to the panel. Make sure the screws are torqued to 2 ± 0.1 N·m (18 ± 1 lbf-in) Section 2.2 Connecting Power The RX5000 supports dual redundant AC and/or DC power supplies that can be installed in any combination. The use of two power modules is recommended to provide redundancy and load balancing. The RX5000 is equipped with a screw-type terminal block, which provides power to both power supplies. The terminal block is installed using Philips screws and compression

More Instructions:

	Siemens RUGGEDCOM RX5000 Reference manual 13-08-2022 148	DOWNLOAD
	Siemens RUGGEDCOM RX5000 Installation manual 07-03-2024 44	DOWNLOAD

Related Products and Documents (Multi-service Platforms):

Comparable Devices:

Similar Resources:

• Ceragon FibeAir IP-20S Assured (105 pages) Installation Guide FibeAir® IP-20S FibeAir® IP-20S Assured Part ID: BM-0280-0 | Doc ID: DOC-00038494 Rev D.04 June 2017 © Copyright 2017 by Ceragon Networks Ltd. All rights reserved. …

• Cisco ONS 15600 (280 pages) Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706 USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-4100Cisco ONS 15600 Reference ManualProduct and Documentation Release 6.0 Last Updated: October 2008Text Part Number: 78-16899-01 …

• Ceragon FibeAir IP-20 All-Outdoor Series (825 pages) User Guide FibeAir® IP-20 All-Outdoor Products: IP-20C IP-20C-HP IP-20S IP-20E IP-20V December 2018 Rev S.02 | CeraOS 10.5 © Copyright 2018 by Ceragon Networks Ltd. All rights reserved. …

• Cisco ONS 15454 Series (166 pages) Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706 USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-4100Cisco ONS SONET TL1 Reference GuideCisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15600Product and Documentation Release 6.0 December 2009Text Part Number: 78-17045-01 …

• Festo CPX-FB36 (3 pages) Bus nodeCPX-FB36Festo SE & Co. KG Postfach73726 Esslingen Germany+49 711 347-0www.festo.comBrief description 80674821611a[8067484]Original: deBus node CPX-FB36 English............................................1 Use for intended purposeThe module described in this document is intended for use as a participant in networks with the protocols EtherNet/I …

• Banner SureCross FlexPower DX99 Series (8 pages) Switch configurable temperature Node with thermocouple/thermistor inputs and two discrete inputs (powered by external battery moduleonly)For additional information, updateddocumentation, and accessories, re-fer to Banner Engineering's website, www.bannerengineering.com/sure-cross.The SureCross® wireless system is a radio frequency network with integrat …

Comments, Questions and Opinions: