Siemens RUGGEDCOM RMC40 Installation Manual

Text of Siemens RUGGEDCOM RMC40 User Guide:

• Siemens RUGGEDCOM RMC40, Chapter 3 Communication Ports RUGGEDCOM RMC40 Installation Guide 12 Copper Ethernet Ports WARNING! Electric shock hazard – risk of serious personal injury and/or equipment interference. If shielded cables are used, make sure the shielded cables do not form a ground loop via the shield wire and the RJ45 receptacles at either end. Ground loops can cause excessive noise and interference, but more importantly, create a potential shock hazard that can result in serious injury. IMPORTANT! For substation applications, do not use the copper Ethernet port to interface with field devices across distances that could produce high levels of ground potential rise (i.e. greater than 2500 V) durin

• Chapter 1 Introduction RUGGEDCOM RMC40 Installation Guide 2 Description Simple Plug and Play Operation • Automatic learning of up to 2048 MAC addresses • Auto-negotiation on 10/100Base-TX ports simplifies setup • Auto-MDI/MDIX on all 10/100Base-TX ports eliminates need for crossover cables • LED indicators for link, activity, and speeds LED aids in field tro

• Siemens RUGGEDCOM RMC40, RUGGEDCOM RMC40 Installation Guide Chapter 2 Installing the Device General Procedure 5 Installing the Device The following sections describe how to install the device, including mounting the device, installing/removing modules, connecting power, and connecting the device to the network. DANGER! Electrocution hazard – risk of serious personal injury and/or damage to equipment. Before performing any maintenance tasks, make sure all power to the device has been disconnected and wait approximately two minutes for any remaining energy to dissipate. WARNING! Radiation hazard – risk of serious person

• Chapter 4 Technical Specifications RUGGEDCOM RMC40 Installation Guide 16 Fiber Optic Ethernet Port Specifications Wiring Standard e TIA/EIA T568A/B Maximum Distance f 100 m (328 ft) Isolation g 1.5 kV c Auto-negotiating. d Shielded or unshielded. e Auto-crossover and auto-polarity. f Typical distance. Dependent on the number of connectors and splices. g RMS 1 minute. Section4.3

• Siemens RUGGEDCOM RMC40, Chapter 6 Certification RUGGEDCOM RMC40 Installation Guide 22 European Union (EU) Section6.1.2 European Union (EU) This device is declared by Siemens Canada Ltd to comply with essential requirements and other relevant provisions of the following EU directives: • EN 60950-1 Information Technology Equipment – Safety – Part 1: General Requirements • EN 61000-6-2 Electromagnetic Compatibility (EMC) – Part 6-2: Generic Standards – Immunity for Industrial Environments • EN 60825-1 Safety of Laser Products �

• Siemens RUGGEDCOM RMC40, RUGGEDCOM RMC40 Installation Guide Chapter 2 Installing the Device Mounting the Device on a DIN Rail 7 Section2.3.1 Mounting the Device on a DIN Rail For DIN rail installations, the RMC40 can be equipped with a DIN rail bracket pre-installed on the back of the chassis. The bracket allows the device to be slid onto a standard 35 mm (1.4 in) DIN rail. To mount the device to a DIN rail, do the following: 1. Align the slot in the bracket with the DIN rail. 1 1 2 3 Figure2:DIN Rail Mounting 1.DIN Rail 2.DIN Rail Bracket 3.Screw Driver 2. Pull the r

• Siemens RUGGEDCOM RMC40, RUGGEDCOM RMC40 Installation Guide Chapter 3 Communication Ports Copper Ethernet Ports 11 Communication Ports The RUGGEDCOM RMC40 can be equipped with various types of communication ports to enhance its abilities and performance. 3 1 2 Figure6:Port Assignment 1.Port 1 2.Port 2 3.Port 3 4.Port 4 Port Type 1 Copper Ethernet Port 2 Copper Ethernet Port 3 to 4 Fiber Optic Ethernet Port CONTENTS • Section3.1, “Copper Ethernet Ports” • Section3.2, �

• Siemens RUGGEDCOM RMC40, RUGGEDCOM RMC40 Installation Guide Chapter 2 Installing the Device Connecting AC Power 9 • Clamping Voltage: 50 V to 200 V • Insertion Loss: < 0.1 dB at 10 MHz • Peak Surge Current: 10 kA, 8x20µs waveform CONTENTS • Section2.4.1, “Connecting AC Power” • Section2.4.2, “Connecting DC Power” Section2.4.1 Connecting AC Power To connect a high AC power supply to the device, do the following: CAUTION! Electrical hazard – risk of damage to equipment. Before testing the dielectric strength (HIPOT) in the field, remove the braided ground cable connected to the surge ground terminal and chassis ground. This ca

• RUGGEDCOM RMC40 Installation Guide Chapter 4 Technical Specifications Power Supply Specifications 15 Technical Specifications This section provides important technical specifications related to the device and available modules. CONTENTS • Section4.1, “Power Supply Specifications” • Section4.2, “Copper Ethernet Port Specifications” • Sectio

• Siemens RUGGEDCOM RMC40, RUGGEDCOM RMC40 Installation Guide  Table of Contents iii Table of Contents Preface ............................................................................................................. v Alerts .................................................................................................................................................. v Training .............................................................................................................................................. vi Customer Support ............................................

• Siemens RUGGEDCOM RMC40, RUGGEDCOM RMC40 Installation Guide Chapter 6 Certification EMC and Environmental Type Tests 25 Description Test Levels DC Power Ports 2.5 kV common, 1 kV differential mode @ 1MHz AC Power Ports 2.5 kV common, 1 kV differential mode @ 1MHz Signal Ports 5 kV (Failsafe Relay) DC Power Ports 5 kV HV Impulse AC Power Ports 5 kV Signal Ports 2 kV DC Power Ports 1.5 kV Dielectric Strength AC Power Ports 2 kV Environmental Type Tests Test Description Test Levels Severity Levels IEC 60068-2-1 Cold Temperature Test Ad -40 °C (-40 °F), 16 Hours IEC 60068-2-2 Dry Heat Test Bd 85 °C (185 °F), 16 Hou

• Siemens RUGGEDCOM RMC40, RUGGEDCOM RMC40 Installation Guide Chapter 1 Introduction Description 3 State Description Yellow (Solid) Link is established Yellow (Blinking) Port activity Power Supply Terminal A pluggable terminal. For more information, refer to: • Section2.4, “Connecting Power” • Section4.1, “Power Supply Specifications” Communication Ports Receive and transmit data. For more information about the various ports available for the RUGGEDCOM RMC40, refer to Chapter3, Communication Ports.

• Siemens RUGGEDCOM RMC40, Chapter 6 Certification RUGGEDCOM RMC40 Installation Guide 24 EMC and Environmental Type Tests Test Description Test Levels Severity Levels DC Power Ports ± 2 kV Line-to-Earth, ± 1 kV Line-to-Line 3 AC Power Ports ± 4 kV Line-to-Earth, ± 2 kV Line-to-Line 4 Signal Ports 10 V 3 DC Power Ports 10 V 3 AC Power Ports 10 V 3 IEC 61000-4-6 Induced (Conducted) RFI Earth Ground Ports 10 V 3 40 A/m continuous, 1000 A/m for 1 s Note a IEC 61000-4-8 Magnetic Field Enclosure Ports 1000 A/m for 1 s 5 DC Power Ports 30% for 0.1 s, 60% for 0.1 s, 100% for 0.05 s IE

• Siemens RUGGEDCOM RMC40, Chapter 2 Installing the Device RUGGEDCOM RMC40 Installation Guide 8 Connecting Power 113 12 4 4 5 1 Figure3:Panel Mounting 1.RUGGEDCOM RMC40 2.Panel Adapter 3.Mounting Holes 4.Screw 5.Metal Clips 2. Insert the device into the adapter. Make sure the device is secured between the two metal clips. Section2.4 Connecting Power The RUGGEDCOM RMC40 supports a single integrated high AC/DC or low DC power supply NOTE • For 110/230 VAC rated equipment, an appropriately rated AC circuit breaker must be installed.

• Siemens RUGGEDCOM RMC40, Chapter 2 Installing the Device RUGGEDCOM RMC40 Installation Guide 10 Connecting DC Power 3. Using a braided wire or other appropriate grounding wire, connect the surge ground terminal to the chassis ground connection. The surge ground terminal is used as the ground conductor for all surge and transient suppression circuitry internal to the unit. 4. Connect the ground terminal on the power source to the chassis ground terminal on the device. Section2.4.2 Connecting DC Power To connect a high or low DC power supply to the device, do the following: CAUTION! Electrical hazard – risk of damage to equipment. Before testing the dielectric strength (HIPOT) in the field, remov

• Siemens RUGGEDCOM RMC40, RUGGEDCOM RMC40 Installation Guide Chapter 1 Introduction Feature Highlights 1 Introduction The RUGGEDCOM RMC40 is a 4-port, unmanaged Ethernet switch that provides both copper-to-fiber media conversion as well as 10 Mbps to 100 Mbps speed conversion. Specifically designed to operate reliably in electrically and climatically harsh environments, it is well suited for use in mission critical Ethernet networking applications. The RUGGEDCOM RMC40 is packaged in a compact, galvanized steel enclosure that allows either DIN or panel mounting for efficient use of cabi

• Chapter 2 Installing the Device RUGGEDCOM RMC40 Installation Guide 6 Required Tools and Materials 2. Mount the device. 3. Set the operating mode. 4. Connect power to the device and ground the device to safety Earth. 5. Connect the device to the network. 6. Configure the device. Section2.2 Required Tools and Materials The following tools and materials are required to install the RUGGEDCOM RMC4

• Siemens RUGGEDCOM RMC40, RUGGEDCOM RMC40 Installation Guide ii Copyright © 2017 Siemens Canada Ltd All rights reserved. Dissemination or reproduction of this document, or evaluation and communication of its contents, is not authorized except where expressly permitted. Violations are liable for damages. All rights reserved, particularly for the purposes of patent application or trademark registration. This document contains proprietary information, which is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without the prior written consent of

More Instructions:

	Siemens RUGGEDCOM RMC40 Installation manual 14-03-2023 28	DOWNLOAD
	Siemens RUGGEDCOM RMC40 Installation manual 26-10-2023 36	DOWNLOAD

Related Products and Documents (Network Router):

Comparable Devices:

Similar Resources:

• GRASS VALLEY ACAPPELLA (4 pages) PRODUCT DATA SHEETwww.grassvalley.comKEY FEATURESAcappellaM ULT I - F O R M AT U T I L I T Y ROU T I NG SYST EMS The Acappella multi-format utility system of small, single- and mixed-format routers is designed for a variety of broadcast and production settings, including small studios, sports arenas, and space-constrained environments such as mobile produc …

• Cisco AIRONET CB21AG (286 pages) Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706 USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-4100Cisco Aironet 802.11a/b/g Wireless LAN Client Adapters (CB21AG and PI21AG)Installation and Configuration GuideCustomer Order Number: Text Part Number: OL-4211-03 …

• TP-Link TL-WR902AC (2 pages) Frequently Asked Questions (FAQ)Q3. What can I do if I forgot the router’s web management password?• Refer to FAQ > Q2 to reset the router, and then use the default admin (all lowercase) for both username and password to log in.Q4. What can I do if I forgot my Wi-Fi password?• If you have not changed the default wireless password, it can be found …

• Juniper ACX6160 (13 pages) Quick Start GuideACX6160 Universal Metro RouterIN THIS GUIDEAbout This Quick Start Guide | 1Step 1: Prepare Your Site for the ACX6160 | 2Step 2: Unpack the ACX6160 | 2Step 3: Mount the Chassis | 2Step 4: Connect the Grounding Cable | 5Step 5: Connect to the Management Console | 6Step 6: Power On the ACX6160 | 7Step 7: Perform the Initial Configuration | 11Sa …

• Linksys Wireless-B (2 pages) A Division of Cisco Systems, Inc.®Model No.Quick InstallationModel No.WirelessWET11Ethernet BridgeWireless-B12A Attach the Bridge’s antenna.B Plug the included Ethernet network cable into the LAN port on the back panel of the Bridge.C The X-II (MDI/MDI-X) slide switch offers a choice between two settings. Slide the X-II switch to the X position if you are …

• Asus RT-N800HP (3 pages) Quick Start ManualKullanım KlavuzuRT-N800HP Wireless-N800 High Power RouterWireless-N800高功率無線路由器A13520 / First Edition / September 2017ASUS Recycling/Takeback ServicesASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to …

Comments, Questions and Opinions: