Siemens TC35i Terminal Operation & User’s Manual
|
Siemens TC35i Terminal, TC35i AT Command Set 14.2 AT+CPBR s m obil e TC35i_ATC_V02.07 Page 346 of 439 1/30/04 Confidential / Released Maximum length of <text> assigned to the telephone number. The value indicated by the test command is given in octets. If <text> is given as GSM characters each character corresponds to one octet. If the <text> string is given in UCS2, the maximum number of characters depends on the coding scheme used for the alpha field of the SIM according to GSM 11.11, Annex B [18]. As a
Siemens TC35i Terminal, TC35i AT Command Set 18.6 Summary of Unsolicited Result Codes (URC) s m obil e TC35i_ATC_V02.07 Page 433 of 439 1/30/04 Confidential / Released SIM related Commands AT^SCKS ^SCKS: <SimStatus> AT^SSET ^SSIM READY SIM Application Toolkit (SAT) Commands ^SSTN ^SSTN: <cmdType> ^SSTN ^SSTN: <cmdTerminateValue> ^SSTN ^SSTN: 254 ^SSTN ^SSTN: 255 Hardware related Commands AT+CALA +CALA: <text> AT^SBC ^SBC: Undervoltage AT^SBC ^SBC: Overvoltage warning AT^SBC ^SBC: Overvoltage shutdown AT^SCTM ^SCTM_A: <m> AT^SCTM ^SCTM_B: <m> AT Command URC
Siemens TC35i Terminal, TC35i AT Command Set 18.3 Available AT Commands and Dependency on SIM PIN s m obil e TC35i_ATC_V02.07 Page 420 of 439 1/30/04 Confidential / Released AT%D % % % ; AT&S ! ; ; ; ATE ! ; ; ; AT+ICF ; ! ! ! AT+IFC ; ! ! ! AT+ILRR ; % % % AT+IPR ; ! ! ! AT+CMUX ; ! ! ! AT^STPB ; ! ! ! Security Commands AT+CPIN ; ! ! ! AT+CPIN2 ; % % % AT^SPIC ! ! ; ; AT+CLCK ; % ; % AT^SLCK ; % ; % AT+CPWD ; % ; % AT^SPWD ; % ; % Identification Commands ATI ! ; ; ; AT+CGMI ! ! ; ; AT+GMI ! ! ; ; AT+CGMM ! ! ; ; AT+GMM ! ! ; ; AT+CGMR ! ! ; ; AT+G
TC35i AT Command Set 10.7 AT+FCQ s m obil e TC35i_ATC_V02.07 Page 252 of 439 1/30/04 Confidential / Released 10.7 AT+FCQ Copy Quality Checking Syntax Command Description This command controls Copy Quality checking when receiving a fax. Parameter Description 0 No copy quality checking. The ME will generate Copy Quality OK (MCF) responses to complete pages. [1] ME can check 1
TC35i AT Command Set 2.14 AT^SCFG s m obil e TC35i_ATC_V02.07 Page 57 of 439 1/30/04 Confidential / Released Examples EXAMPLE 1 Enable sending of a short message (SMS) on next DTR activation (OFF-ON transition). Sent SMS is assumed to be stored at first location of storage selected with AT+CPMS and AT^SSMSS, i.e. SMS may be sent from either SIM or ME storage. Also refer to AT+CMSS an
Siemens TC35i Terminal, TC35i AT Command Set 9.2 AT^SACM s m obil e TC35i_ATC_V02.07 Page 215 of 439 1/30/04 Confidential / Released Parameter Description [0] (&F) suppress unsolicited result code 1 display unsolicited result code Three bytes of the current ACM value in hexadecimal format (e.g. "00001E" indicates decimal value 30) 000000- FFFFFF Three bytes of the max. ACM value in hexadecimal format (e.g. "00001E" indicates decimal value 30) 000000 disable ACMmax feature 000001-FFFFFF Three bytes of the current CCM value in hexadecimal
Siemens TC35i Terminal, TC35i AT Command Set 8.6 AT^SMOND s m obil e TC35i_ATC_V02.07 Page 195 of 439 1/30/04 Confidential / Released Parameter Description integer or sum of integers each representing a class of requested information, i.e. a group of output values. parameter format can be determined by summing up the values for each of the requested classes of information. The possible values and their associated information are listed below. Value 0 is not allowed. The default value and the maximum value are 15, representing the sum of all possible class values, leading to the output of all available informatio
Siemens TC35i Terminal, TC35i AT Command Set 11.22 AT^SLMS s m obil e TC35i_ATC_V02.07 Page 315 of 439 1/30/04 Confidential / Released Number of messages currently stored in the SMS memory of the Mobile Equipment (physical storage "ME") Concatenated logical SMS storages of SIM ("SM") and Mobile Equipment ("ME"). Sum of all messages currently stored, indicated as "MT". <used2> (num) <used3> (num)
Siemens TC35i Terminal, TC35i AT Command Set 14.8 AT^SPBS s m obil e TC35i_ATC_V02.07 Page 360 of 439 1/30/04 Confidential / Released Parameter Description 1 To make a step forward in the alphabetically sorted phonebook. 2 To make a step backward in the alphabetically sorted phonebook. 1...maxindex The index in the sorted list of phonebook entries that identifies the first entry in alphabetical order of names displayed. The value of <index-a> is determined by the value of the internal counter and by parameter <value>. After a write command has terminated successfully with "OK", the value from parameter <index-a> is saved and retai
Siemens TC35i Terminal, TC35i AT Command Set 15.12 AT^SNFM s m obil e TC35i_ATC_V02.07 Page 381 of 439 1/30/04 Confidential / Released • This command can be used in all audio modes (1 to 6) and during a voice call only. See AT^SNFS for more details on the various audio modes. • During an active call, users should be aware that when they switch back and forth between different audio modes (for example handsfree on/off) the value of <mute> does not change, i.e. the microphone mode is retained until explicitly changed. • As alternative, you can use the AT+CMUT command.
Siemens TC35i Terminal, TC35i AT Command Set 11.12 AT+CPMS s m obil e TC35i_ATC_V02.07 Page 298 of 439 1/30/04 Confidential / Released Number of messages currently in <mem2> Number of messages currently in <mem3> Number of messages storable in <mem1> Number of messages storable in <mem2> Number of messages storable in <mem3> Notes • The Mobile Equipment storage ''ME'' offers space for 25 short messages, see <mem1>. • ''MT'' is the sum of ''ME&ap
Siemens TC35i Terminal, TC35i AT Command Set 11.9 AT+CMSS s m obil e TC35i_ATC_V02.07 Page 290 of 439 1/30/04 Confidential / Released 11.9 AT+CMSS Send SMS messages from storage Syntax Command Description The write command sends message with location value <index> from message storage <mem2> to the network (SMS-SUBMIT or SMS-COMMAND). If new recipient address <da> is given for SMS-SUBMIT, it shall be used instead of the one stored with the message. Reference value <mr> is returned to the TE on successful message delivery. Value can be used to identify message upon unsolicited delivery status report result code. If the
Siemens TC35i Terminal, TC35i AT Command Set 4.3 AT&D s m obil e TC35i_ATC_V02.07 Page 88 of 439 1/30/04 Confidential / Released 4.3 AT&D Set circuit Data Terminal Ready (DTR) function mode Syntax Command Description This parameter determines how the TA responds when circuit 108/2 (DTR) is changed from ON to OFF during data mode. Parameter Description [0] TA ignores status of DTR. 1 ON->OFF on DTR: Change to command mode while retaining the connected call. 2 (&F) ON->OFF on DTR: Disconnect data call, change to com
Siemens TC35i Terminal, TC35i AT Command Set 2.9 AT+CFUN s m obil e TC35i_ATC_V02.07 Page 42 of 439 1/30/04 Confidential / Released EXAMPLE 2 To set the ME to NON-CYCLIC SLEEP mode enter When, for example, an SMS is being received and indicated by an unsolicited result code (URC), the ME wakes up to full operation. Note that the URC used in this example will appear only, if AT+CNMI=1,1 was configured before. After this, you may want to verify the operating status: EXAMPLE 3 To stop CYCLIC SLEEP mode and return to full functionality: Remember that this approach is not applicable to
Siemens TC35i Terminal, TC35i AT Command Set 2.2 AT&V s m obil e TC35i_ATC_V02.07 Page 30 of 439 1/30/04 Confidential / Released Table 2.1: Current configuration on ASC0 / MUX channel 1 (example) PIN authentication done No PIN authentication ACTIVE PROFILE: E1 Q0 V1 X4 &C1 &D2 &S0 \Q0 \V1 S0:000 S3:013 S4:010 S5:008 S6:000 S7:060 S8:000 S10:002 S18:000 +CBST: 7,0,1 +CRLP: 61,61,78,6 +CR: 0 +FCLASS: 0 +CRC: 0 +CMGF: 0 +CSDH: 0 +CNMI: 0,0,0,0,1 +ICF: 3 +IFC: 0,0 +ILRR: 0 +IPR: 57600 +CMEE: 2 ^SMGO: 0,0 +CSMS: 0,1,1,1 ^SACM: 0,"000000","000000" ^SCKS: 0,1 ^SSET: 0 +CREG: 0,1 +CLIP: 0,2 +CAOC: 0 +COPS: 0,0,
TC35i AT Command Set 11.28 AT^SSMSS s m obil e TC35i_ATC_V02.07 Page 325 of 439 1/30/04 Confidential / Released 11.28 AT^SSMSS Set Short Message Storage Sequence Syntax Command Description The short message storage ''MT'' (see AT+CPMS) is a logical storage. It consists of two physical storages ''ME'' and ''SM''. This command allows to s
TC35i AT Command Set 15.6 AT+VTD s m obil e TC35i_ATC_V02.07 Page 370 of 439 1/30/04 Confidential / Released 15.6 AT+VTD Tone duration Syntax Command Description This command refers to an integer <duration> that defines the length of tones transmitted with the AT+VTS command. Parameter Description duration of the tone in 1/10 second 1 (&F) ...255 Test Command AT+VTD=
Siemens TC35i Terminal, TC35i AT Command Set 1.5 Supported character sets s m obil e TC35i_ATC_V02.07 Page 18 of 439 1/30/04 Confidential / Released 1.5 Supported character sets The ME supports two character sets: GSM 03.38 (7 bit, also referred to as GSM alphabet or SMS alphabet) and UCS2 (16 bit, refer to ISO/IEC 10646). See AT+CSCS for information about selecting the character set. Character tables can be found below. Explanation of terms •IRA IRA means that one byte is displayed as two characters in hexadecimal format. for example, the byte 0x36 (
Siemens TC35i Terminal, TC35i AT Command Set 10.24 AT+FRS s m obil e TC35i_ATC_V02.07 Page 269 of 439 1/30/04 Confidential / Released 10.24 AT+FRS Receive Silence Syntax Command Description <time>=n causes the TA to report an OK result code to the TE after <time> 10 millisecond intervals of silence have been detected on the line. This command is aborted if any character is received by the DTE. The modem discards the aborting character and issues an OK result code. An ERROR response code results if this command is issued while the mode is on-hook Parameter Description no. of 10 millisecond intervals 0...255 Note • Used for Fax C
TC35i AT Command Set 2.7 AT\V s m obil e TC35i_ATC_V02.07 Page 37 of 439 1/30/04 Confidential / Released 2.7 AT\V Set CONNECT result code format Syntax Parameter Description [0] CONNECT <text> result code returned without RLP trailer 1 (&F) CONNECT <text> result code returned with RLP trailer Notes • For circuit switched data calls only. • Output only if ATX p
Siemens TC35i Terminal, TC35i AT Command Set 9.5 AT+CCUG s m obil e TC35i_ATC_V02.07 Page 221 of 439 1/30/04 Confidential / Released Parameter Description explicit CUG invocation options 0 (D) Deactivate explicit CUG invocation 1 Activate explicit CUG invocation 0-9 explicit selection of CUG index 10 (D) No index (preferred CUG taken from subscriber data) state of the call 0 (D) no information 1 suppress outgoing access 2 suppress preferential CUG 3 Suppress preferential CUG and Outgoing Access. Notes • The active settings for omitted parameters are retained without changes. • Explicit CUG invocation means that at each call setup
Siemens TC35i Terminal, TC35i AT Command Set 3.2 AT+CIND s m obil e TC35i_ATC_V02.07 Page 67 of 439 1/30/04 Confidential / Released +CIEV: smsfull,0 +CIEV: rssi,5 Receive with full signal field strength ATD0123456; Make a call. OK +CIEV: sounder,1 Receive a set of "+CIEV" URCs reports. +CIEV: call,1 +CIEV: sounder,0 +CIEV: call,0 The receiver hangs up. NO CARRIER AT+CIND=,,,0,,0 Deregister the indicators "call" and "sounder" OK ATD0123456; Rebuild the same call. OK This time, no URCs are displayed. NO CARRIER
Siemens TC35i Terminal, TC35i AT Command Set 14. Phonebook Commands s m obil e TC35i_ATC_V02.07 Page 343 of 439 1/30/04 Confidential / Released 14. Phonebook Commands The AT Commands described in this chapter allow the external application to access the phonebooks located in the TC35i's memory or on the attached Subscriber Identity Modul (SIM). 14.1 Sort Order for Phonebooks Due to the support of UCS2 for the <text> part of phonebook entries, the sort order for phonebook records fol- lows the algorithm published as Unicode Technical Standard #10, "Unicode Collation Algorithm". A memory-optimiz
Siemens TC35i Terminal, TC35i AT Command Set 4.10 AT+IPR s m obil e TC35i_ATC_V02.07 Page 100 of 439 1/30/04 Confidential / Released 4.10 AT+IPR Set fixed local rate The command AT+IPR can be used to set or query the DTE-DCE interface bit rate. Syntax Command Description The test command returns the values of the supported automatically detectable bit rates and the values of the supported fixed bit rates. The read command returns the current bit rate of the interface. The write command specifies the bit rate to be used for the interface. When you set a fixed-rate, make sure that bot
Siemens TC35i Terminal, TC35i AT Command Set 10.2 AT+FBADLIN s m obil e TC35i_ATC_V02.07 Page 246 of 439 1/30/04 Confidential / Released 10.2 AT+FBADLIN Bad Line Treshold Syntax Command Description This command defines the Copy-Quality-OK-threshold. If <badlin> consecutive lines have pixel count errors in normal resolution (98 dpi) mode, then the copy quality is unacceptable. If <badlin> * 2 consecutive lines have pixel count errors in fine resolution (196 dpi) mode, then the copy quality is unacceptable. "Copy Quality Not OK" occurs if either the error percentage is too high or too many consecutive lines contain errors. A value of 0 implies that error checking is not
Siemens TC35i Terminal, TC35i AT Command Set 2. Configuration Commands s m obil e TC35i_ATC_V02.07 Page 28 of 439 1/30/04 Confidential / Released 2. Configuration Commands The AT Commands described in this chapter allow the external application to determine the TC35i's behaviour under various conditions. 2.1 AT&F Set all current parameters to manufacturer defaults Syntax Command Description TA sets all current parameters to the manufacturer defined profile. Parameter Description [0] set all TA parameters to manufacturer defaults Notes • List of parameters reset to manufacturer default can be found in Chapter Factory De
Siemens TC35i Terminal, TC35i AT Command Set 3.4 AT+CEER s m obil e TC35i_ATC_V02.07 Page 77 of 439 1/30/04 Confidential / Released Resource unavailable class 34 No circuit/channel available 38 Network out of order 41 Temporary failure 42 Switching equipment congestion 43 Access information discarded 44 Requested circuit/channel not available 47 Resource unavailable, unspecified Service or option not available class 49 Quality of service unavailable 50 Requested facility not subscribed 55 Incoming calls barred within the CUG 57 Bearer capability not authorized 58 Bearer capability not presently available 63 Service or option not available, unspecified Service or option not implemented 65
TC35i AT Command Set 14.4 AT+CPBW s m obil e TC35i_ATC_V02.07 Page 349 of 439 1/30/04 Confidential / Released 14.4 AT+CPBW Write into Phonebook This command serves to write onto an entry of the phonebook selected with AT+CPBS. It can be used only after the phonebook's data has been read successfully from the SIM. Reading starts after successful SIM authentica- tion has been performed a
Siemens TC35i Terminal, TC35i AT Command Set 9.6 AT+CCFC s m obil e TC35i_ATC_V02.07 Page 222 of 439 1/30/04 Confidential / Released 9.6 AT+CCFC Call forwarding number and conditions control Syntax Command Description The Test command returns the supported parameters. The write command controls the call forwarding supplementary service. Registration, erasure, activation, deac- tivation and status query are supported. Parameter Description reason for call forwarding 0 unconditional 1 mobile busy 2 no reply Test Command AT+CCFC=? Response(s) +CCFC:(list/range of supported <reason>s) OK Write Com
DOWNLOAD |
Siemens MC35 Modem Command set
MC35 |
Siemens 6ES7134-4JB00-0AB0 Modem Manual
6ES7134-4JB00-0AB0 |
Siemens SE366 Modem Quick start manual
SE366 |
Siemens Simatic S7-300 Modem Getting started
Simatic S7-300 |
Siemens TC65 Modem Operation & user’s manual
TC65 |
Siemens Simatic S7-300 Modem Configuration manual
Simatic S7-300 |
Siemens 1015N-2MFM-1A Modem Field manual
1015N-2MFM-1A |
Siemens Simatic S7-300 Modem Operation & user’s manual
Simatic S7-300 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Giant | P217 | Operating instructions/ repair and service manual | giant/p217-F67.pdf | 24 Jul 2023 | 16 | 0.3 Mb |
2 | Block | CVR-100+ MKII | Instruction manual | block/cvr-100-mkii-F11.pdf | 09 Feb 2024 | 35 | |
3 | Compaq | CQ2300 - Desktop PC | Setup poster | compaq/cq2300-desktop-pc-OGK.pdf | 24 Jul 2023 | 1 | |
4 | Canon | POWERSHOT A700 | Operation & user’s manual | canon/powershot-a700-9KE.pdf | 04 Apr 2023 | 139 | 10.33 Mb |
5 | Philips | Xenium | Operation & user’s manual | philips/xenium-B47.pdf | 23 May 2023 | 70 | 2.16 Mb |
6 | Lexicon | 480L - V3.01 UPGRADE | Manual | lexicon/480l-v3-01-upgrade-D6E.pdf | 13 Feb 2023 | 2 |
ETM
UMTS/GSM/GPRS Terminal – ETM9140-1 GSM/GPRS Terminal – ETM9120-1 Features: ◩ 3G (HSPA+/UMTS) Connectivity – ETM9140-1 only ◩ 2G (GSM/GPRS) Connectivity ◩ Standard RS232 9DF serial port ◩ 5v to 35v power input on RJ12 connector ◩ 7 x I/O’s on RJ45 connector ◩ FME M antenna connector ◩ Sleep Mode for reduced power …
ETM9120-1(46 pages) |
AT&T
Find More InformationManage Your Account with myAT&T• On the web: att.com/myATTCompatible device and online account required. Data and messaging rates may apply for download and app usage.Need More Help?• On the web: att.com/DeviceHowToGive us a Call• 611 from any AT&T wireless phone• 800.331.0500 or prepaid 800.901.9878Data rates may apply. …
USB800(2 pages) |
Zoom
ZOOM MODEM Quick Start This Quick Start tells you how to install your modem with a Windows PC. Detailed information about advanced features and installation instructions for Macintosh and Linux are in the User Guide on the CD. The modem requires that you have ADSL service, which is usually called DSL in the USA. Important Safety Measures • To reduce the r …
1640A(4 pages) |
Murata
Revision History Revision Date Author Change Description 1 09/02/2005 F. Perkins Initial issue 2 01/27/2015 R. Willett Reformatted to comply with new Murata V.I. RFM products are now Murata products. HN-250/HN-250X Outdoor Base/Remote User Guide ©2009-2015 by Murata Electronics N.A., Inc. HN-250/HN-250X Rev. 2.0 …
HN-250(60 pages) |
KVH Industries
This guide provides basic operation information for the TracPhone V11-IP. For complete operation, setup, and diagnostics information, refer to the system’s comprehensive Help, available on the Support tab of the TracPhone V11-IP web interface. If you need any assistance, please contact KVH Technical Support.TracPhone® V11IP Quick Start GuideTechnical Supp …
TracPhone V11IP(2 pages) |
Matrix Electrónica
MTX-65i Family www.mtxm2m.com www.matrix.es 2015/04 v3.4 Page 1/106 MTX Terminals® by MATRIX ELECTRONICA S.L.U MTX-65i Family User Manual
…
MTX-65i(106 pages) |
LG Microwave Oven MB-394ALG MB-394A Manual (Doc Type: Microwave Oven Service manual) MB-394A, 7 |
Panasonic Handsets KX-TGA830EX#36CKQ1: KX-TGA830EX Handsets Installation manual KX-TGA830EX, 80 |
Alternate Heating Boiler WC40Boiler Installation and operator's manual (Alternate Heating WC40) WC40, 31 |
Onkyo Stereo Receiver TX-SR804User Manual: Onkyo TX-SR804 (L8C77F, Upd.Wed 12.2023) TX-SR804, 96 |
Philips Coffee Maker HD5730 QSC#B2T182 HD5730 QSC: Philips Coffee Maker Owner Documentation HD5730 QSC, 11 |
thomann Fog Machine Stairville Hz-200 DMXthomann Stairville Hz-200 DMX Guide (Operation & user’s manual), @1Y8327 Stairville Hz-200 DMX, 36 |
Millipore Water Filtration Systems direct-q 3 RPDF Manual (@F44VB5), Millipore direct-q 3 R Water Filtration Systems (16th Jan 2024) direct-q 3 R, 80 |
Mares Diving Instrument Puck AirDiving Instrument PDF Operation & user’s manual Puck Air, 19 |
Toro Lawn Mower Z287L Z MasterLawn Mower Operator's manual (Toro Z287L Z Master) Z287L Z Master, 56 |
ZyXEL Communications Network Card 802.11G G-210HNetwork Card #P179TG 802.11G G-210H, 2 |
LEDX Headlamp Cobra IIxLEDX Cobra IIx User Manual (Manual ), @69V454 Cobra IIx, 8 |
Salcom Transmitter 11-08-0000PDF Manual (@G1IIYQ), Salcom 11-08-0000 Transmitter (26.02.2024) 11-08-0000, 4 |